Search Documents

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as on control of furnace practice. This chapter deals only with those raw materials of the basic open-hearth process which are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, and alloying and deoxidizing additions. Refractories, which may also affect the slag composition, are discussed in the previous chapter. Wide variations are possible in the type and composition of charged materials, but in all cases certain fundamental relationships among the elements of the charge must be maintained. Since the process consists essentially of refinement by oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters II and VII). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme would be the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not subject to oxidation or other reactions resulting in their elimination, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type would be found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should below in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the scrap, so that the average copper content of the melt will be below the required maximum.

Jan 1, 1944

By Thomas E. Howard

Tunneling is at the threshold of a new era. An exciting new technology is becoming available. And, supplying the increasing quantities of minerals required by a growing and socially advancing world population, together with providing the subsurface facilities attendant to the rapid urbanization of the more developed countries of the world, will require underground excavation during the next decades on a scale that would have seemed fantastic a few years ago. It is estimated that world mineral consumption will increase fivefold by the year 2000. Projections for the United States indicate that domestic consumption of nonfuel minerals may increase two to three times by the end of the century. Meeting these requirements will entail opening up many new underground mines, even if present trends toward surface mining continue. And, at least in the United States, new factors that are becoming increasingly important may modify these trends. We are depleting our shallow easy- to-find and easy-to-mine mineral deposits; and, if we are to avoid becoming dangerously dependent on imports, we must turn more and more toward deeper deposits that are not amenable to surface mining. Growing public concern with environmental quality is apparently leading toward increasingly stringent regulation of surface mining which also will tend to make underground mining economically more attractive. The world market for underground construction is also growing rapidly. The most conservative projections indicate that in the United States alone more than $7.0 billion will be spent on excavation for underground facilities during the next ten years. And these estimates do not include any of the bold, imaginative new applications for underground excavation that have been proposed, such as extensive underground power transmission, the Chicago Deep Tunnel plan, and the Northeast Corridor Transportation project. There can be little doubt then that the market for tunnels for conventional applications is increasing rapidly and that the trend will continue. It

Jan 1, 1970

By P. R. Sperry, M. L. Holzworth, P. A. Beck

The basic work of Z. Jeffries 1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria had been added, Jeffries found that grain growth was inhibited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. such a a temperature" was later found by Gross-mann~3,14 in certain types of steel, while ~~i~ showed15 that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently, 20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases with the titanium content. That coarsening may occur, as a result of, certain heat treatments, even in low carboil rimmed sheet steel, was shown by Samuels. He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material. In this instance the identity of the inhibiting phase has not been determined. However, Tangerding found23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction. The carbide particles Can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air is followed between in hydrogen for 75 hr at the Same temperature, grain growth is more hibition usually the whole specimen is transformed into a single crystal (approx. 1.5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth hibition from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced rtain the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pet Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1949

By W. Crafts, J. L. Lamont

Secondary hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to thc secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at II00 F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader. Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to IIOOOF, but the mechanism of the process has received little consideration.

Jan 1, 1949

By G. K. Manning, A. R. Elsea, A. B. Westerman

INTRODUCTION A CONSIDERABLE number of high-temperature alloys, that is, alloys which have load-carrying ability at elevated temperatures, have been developed on an empirical basis. In order to determine why these alloys possess this particular ability, a project was started at Battelle Memorial Institute on the fundamental factors promoting high-temperature strength of alloys. At the time of inception of this study, the cobalt-base alloy, Vitallium, was widely used because of its good high-temperature properties. One phase of this study was to include an investigation of the structures observed in Vitallium after various heat treatments. However, before investigating the structural features of Vitallium, it appeared logical to examine the phase diagrams of the related binary systems in order to develop information as to which phases- might be present in Vitallium. A preliminary survey of the pertinent alloy systems was made, with particular emphasis on the cobalt-chromium system, which is the base for the Vitallium series of alloys. The early work of Lewkonja1 and Guertler2 indicated that cobalt and chromium are completely miscible in the liquid state, and, within a narrow temperature range, in the solid state; that the liquidus shows a minimum; and that the alloys containing 45 to '85 pct chromium undergo a transformation at 1200 to 1250°C. More recently, Wever and Haschimoto,3 Wever and Lange,4 and Matsunaga5 carried out experimental work which led to the diagrams shown in Fig I and 2. Both diagrams are based on thermal analysis, metallographic, magnetic, and dilatation data; in addition, X ray diffraction results were used by Wever and Haschimoto, and electrical resistance measurements by Matsunaga. It is apparent from a comparison of the two diagrams that there was a difference of opinion as to the locations of the boundaries of the various phases, and as to the existence of a phase containing approximately 47 pct chromium. With these exceptions noted, it might be pointed out that the two diagrams are similar, and that, in general, any particular reaction which is shown on both diagrams occurs at a lower temperature on the Matsunaga diagram than on that of Wever-Haschimoto-Lange. Thus, in view of the gaps in the data and the questionable features in the published diagrams, it appeared desirable to start the fundamental study of Vitallium by determining the diagram for the cobalt-chromium system. EXPERIMENTAL WORK For the convenience of the reader, the diagram as determined by the present investigation is presented in Fig g. The liquidus and solidus data for the low-chromium alloys were taken from the work of Wever and Haschimoto,3 while the, melting point for pure chromium is the

Jan 1, 1948

By O. N. Carlson, W. M. Paulson

A phase diagram is proposed for the Y-C system based on the vesults of thermal analyses, microscopic obsevvations, and X-ray diffraction studies. Three intermediate phases occur in the system: a congru-ently melting fcc phase with a wide range of homogeneity about the composition Y2C, an intermediate solid-solution region between 55 and 58 at. pct C, and a bct dicarbide melting congruently at 2415°C. All three compounds undergo a phase transformation at elezlated temperatures. A continuous serzes of solzd solutions exists between the fcc phase and the high-temperature form of YC2 with a maximum in the solidus at 2000°C and 30 at. pct C and a minimum at 1805°C and 54 at. pct C. THIS investigation of the Y-C system was undertaken as part of a nuclear materials development program. Yttrium-base alloys are of interest as possible containers for liquid metals, and carbides are currently receiving increased attention as high-temperature materials for advanced reactors and other applications. Previous work on this system was limited in scope, and the results were somewhat inconclusive and at times contradictory. Spedding et al.&apos; reported the existence of a triyttrium carbide having an fcc structure with a wide range of homogeneity and Dean et a1.2 reported the existence of a rhombohedra1 phase having the stoichiometry of Y2C. Bachella et a1.3 observed that the latter was the result of ordering of carbon atoms in the fcc solid solution. The ordering range was placed at 800" to 1000°C. Vickery et a1.4 reported a high-melting compound which they identified as yttrium dicarbide, and Spedding and coworkers1 determined the structure of this phase as bct with lattice parameters a = 3.66 and c = 6.17A. Samsonov et al.5 reported the melting point of YC2 as 2300" * 50°C. Recently Bowman et a1.6 found a transformation in the dicarbide from the tetragonal to an fcc form at 1320 20°C. Samsonov and coworkers7 reported a monocarbide of yttrium melting at 1950" * 20°C and also a sesqui-carbide melting at 1800" * 50°C. The existence of the latter has also been indicated by others,1&apos;8 but neither compound has been definitely established. The Y-C phase diagram shown in Fig. 1 was proposed by Chubb and Keller8 in 1964 based on the data available at that time. The tentative nature of this diagram together with the uncertain status of the compounds indicated that additional work on this system was needed. EXPERIMENTAL PROCEDURE Yttrium metal of 99.9 pct purity was prepared for use in this study by the reduction of YCl, with calcium to form a sponge product.9 The major impurities in this material were as follows: 100 ppm C, 150 pprn H, 20 ppm N, 300 to 1000 ppm O, <20 ppm Ca, <100 ppm Cr, <80 ppm Cu, 150 ppm Fe, <30 pprn Mg, <400 ppm Ta, and <100 ppm Ti. Alloys were prepared by arc melting yttrium sponge together with pieces of high-purity graphite rod in a purified argon atmosphere. Homogeneity was insured by repeated melting, inverting the ingot between melts.

Jan 1, 1969

By William H. Hamilton

Tunnel-driving capabilities in terms of feet per hour have advanced several hundred percent in the last century. Indications are that this capacity will double each decade for the next three decades. These future improvements will be made possible by a greatly increased need for underground excavation and the awareness of industry of its own latent capabilities. The factors of most interest to any potential user of a tunneling machine are those making possible an increase in production. The first and most obvious factor, and probably the one that has created the excitement and interest of most people, is the increase in boring rate through faster rock fracture and improved support systems. Boring rate can be increased by more horsepower in the form of increased thrust, torque, and cutterhead speed, and by better cutters and cutting methods, better material-handling systems, and better ground-control systems. All of these items are extremely important and are the basis of much discussion and effort by everyone concerned with the excavation of tunnels by machine. The second factor, just as obvious and equally important as an increase in boring rates, is "increase in production through better utilization of the tunneling machine and related equipment," which means a reduction in downtime through greater reliability of equipment. Mechanical rock attack is presently capable of cutting hard rock at 5 fph and soft rock at more than 20 fph. In current practice, however, this advance rate is maintained for less than 50% of the shift time. I predict that tunnel-driving contractors and their supporting manufacturers of tunnel-boring equipment will provide machinery that will maintain these advance rates for more than 90% of the shift time. This increase in effective production will be due to the increase in reliability of the tunneling machine and tunneling system components. Such a percentage increase in utilization of the tunneling equipment is just

Jan 1, 1970

By A. J. Mortlock

Cobalt and nickel have been diffused at tracer concentrations in gold at several temperatures in the range from approximately 700° to 950°C. The diffusion penetration profiles were determined by a serial sectioning technique in which the gold is first anodized and then the anodic layer is dissolved in acid. In this ulay sections as thin as 250A could be removed reproduci-bly. In all cases, the region close to the specimen surface was characterized by irregular behavior in the sense that the logarithm of concentration was not linear in the square of the penetration distance. In sotne cases, there zuas an indication of the operation of very slow dijfusion in this region, while in others the apparent diffusion coejj&apos;icient was negative. Possible reasons for this anomalous behavior are briefly discussed. In recent years it has been found that the region close to the surface of a metal can sometimes exhibit anomalously slow diffusion characteristics relative to the interior of the metal. One of the best examples of this fact is the work of Styris and omizuka,&apos; who showed that the apparent diffusion coefficient for zinc in the region withi: about 1 p of the free surface of copper was about ,,,, that at deeper penetrations. This result is particularly interesting, because it is free from the possibly complicating effects of low solubility of the diffusing tracer in the solvent metal. In the case of diffusion under conditions of low solubilitjr, interpretaticn of the results in terms of lattice diffusion is difficult because of the enhanced short-circuiting produced by segregation to dislocations.2&apos;3 Measurements by Duhl et 1. suggest that cobalt diffusing in gold may also show a near-surface effect of this type. Once again the solubility is high, so that this result could be of great interest. However, the technique used for analyzing the diffusion penetration zones by Duhl, viz. the counting of residual gamma activity in the specimen following sectioning, appears to have indicated a near-surface effect in a parallel experiment on the self-diffusion of gold reported at the same time. The latter result is known to be spurious, since Kidson5 has demonstrated that self-diffusion in gold does not show this effect. Duhl et 01. also reported some measurements on the diffusion of nickel in gold, but failed to give any data for the near-surface region. As the solubility of nickel in gold is high, such data would also be of special interest. We, therefore, decided to conduct another set of experiments on the diffusion of nickel and cobalt in gold, using a sectioning technique that allows the individual sections to be assayed for solute content and thus gives direct determinations of penetration profiles. Also, by sectioning with an anodizing/stripping tech- nique, very thin layers can be removed and the region close to the surface studied in detail. MATERIALS The gold specimens were supplied as single crystal disks $ in. in diam by a in. high by Monocrystals Co. of Cleveland, Ohio. The gold itself was of spectro-scopic purity, i.e., better than 99.99 pct pure. METHOD Specimen Preparation. One flat end face of each gold crystal was spark planed with a Servomet spark erosion machine set for minimum spark energy. Following this treatment the crystals were preannealed for 2 to 4 days at temperatures of either 400" or 700°C. The three crystals preannealed at 700°C showed signs of recrystallization. The spark-planed end face of each crystal was then coated with the appropriate amount of 63i or 60 radioactive tracer. This deposit was laid down in a simple plating bath containing the as-supplied solution of the radioactive isotope as well as sufficient ammonium oxalate to saturate the solution. Some ammonium oxalate remained undissolved on the floor of the bath for this purpose. During plating further additions of ammonium oxalate were sometimes required to allow the plating to continue satisfactorily, perhaps due to passivation of the undissolved oxalate already present. The thickness of the deposited layer was determined by comparison of the apparent surface activity of the plated specimen with that of a similar specimen having a weighable deposit of the isotope on its end face. Correction for self-absorption of the radiation was made in this calculation. Annealing. The deposited crystals were annealed in a hydrogen atmosphere in sealed silica tubes. During this heat treatment they were supported, active face down, on optically flat silica plates. The temperature was measured with calibrated Pt vs Pt-10 pct Rh thermocouples, and the tabulated values can be taken to be correct to Z°C. All the crystals showed evidence of recrystallization following these heat treatments, suggesting that initially they may not have been good single crystals or had suffered strain during delivery. Concentration Profile Analysis. After annealing, the crystals were sectioned by the anodizing-stripping technique.6 The anodizing involved suspension of the specimen with its cylindrical axis horiz6ntal by a gold wire in a 200-ml beaker containing 1 M Hg304. A cathode in the form of a strip of gold sheet, 2 in. wide and positioned to be in contact with the curved side of the beaker, completely encircled the specimen. An anodizing current of 30 ma, corresponding to a current density of 5 ma per sq cm on the surface of the specimen, was passed for times ranging from 5 to 150 min depending on the thickness of gold to be removed; the solution was stirred continuously during this process. Following this treatment, the specimen

Jan 1, 1969

By G. R. Speich, Morris Cohen

The growth rate of bainite has been determined by hot-stage metallography in five hypereutectoid high-purity iron-carbon, iron-carbon-chromium, and iron-carbon-nickel alloys. The studies have been confined essentially to lower bainite. The growth rate is independent of time at constant temperature, but both the edgewise and sidewise growth rates increase with increasing temperature. Increasing the carbon content, or adding chromium or nickel, decreases the growth rate without greatly affecting the temperature dependence. The results lead to separate diffusion-controlled models for the edgewise and sidewise growth rates. ALTHOUGH bainite has been subject of many detailed investigations,1,2 the growth mechanism of this intermediate transformation product of steel remains unclear. One difficulty has been that practically all the kinetic measurements have been restricted to studies of the overall reaction rate. Only a limited amount of information3, 4-6 is available on the growth process itself. The purpose of the present work was to investigate the effect of time, temperature and composition on the growth rate of bainite using hot-stage metallography. This method makes it possible to observe continuously the isothermal growth of individual bainitic units because of the surface upheavals accompanying their formation.3 This information is needed to test the existing growth models and to obtain a better understanding of the factors controlling the bainitic transformation. EXPERIMENTAL PROCEDURE Alloys—The compositions of the alloys used in the present work are shown in Table I. The five alloys were vacuum-melted and cast, and were prepared from high-purity materials. The three iron-carbon alloys were available from the work of Roberts et al.7 in the form of 3/8-in. diam rods.* To facilitate machining, the rods were ing. The rods were then tempered for 3 hr at 650°C to allow machining. The iron-carbon alloys in Table I were selected for investigating the effect of carbon on the bainitic growth rate. Due to the rapidity of the transformations involved, it was not feasible to measure the growth rates in iron-carbon alloys having carbon contents much less than 0.9 pct C. The iron-carbon-chromium and iron-carbon-nickel alloys were selected to study the influence of chromium and nickel on the growth rate at a carbon level of about 1.1 pct C, since this carbon content was intermediate among the iron-carbon alloys. The concentrations of chromium and nickel were chosen to match isothermal trans formation diagrams in the literature.8&apos;9 Hot-Stage—Since the iron-carbon alloys had such low hardenabilities, it was necessary to quench the hot-stage specimens drastically from the austentiz-ing temperature to the isothermal transformation temperature to prevent the formation of pearlite or proeutectoid constituents. A rapid-quenching metal-lographic hot-stage was built for this purpose. A maximum temperature of about 1100°C and quenching rates up to 500°C per sec could be attained with this equipment. The details of the apparatus are described in a recent publication. After being polished and mounted on the hot-stage, the specimen (0.020 in. thick) was protected from oxidation and decarburization during austenitizing by a vacuum of 10-4 to 10-5 mm. The quench to the reaction temperature was accomplished with a helium blast, and the isothermal run at this temperature was conducted in a helium atmosphere. A fine-wire thermocouple spot-welded to the sample and a high-speed

Jan 1, 1961

By J. H. Jackson, P. D. Frost, C. H. Lorig, L. W. Eastwood, A. C. Loonam

It is well known that for equal weights of material, thin sections of the lighter structural alloys are more resistant to buckling under a compressive stress than thin sections of more dense material. Therefore, structural parts having the same resistance to buckling stresses are generally lightest when they are made of magnesium alloys. Consequently, there is considerable interest in the development of strong alloys having densities equal to or lower than that of magnesium and strength-weight ratios equivalent to those of the strongest aluminum alloys. The development of commercial magnesium-base alloys has been very successful, and their importance among materials in the structural field has been amply demonstrated. However, an even wider structural application of magnesium alloys might be effected if improvements could be made in the cold rollability and cold-forming characteristics. Such improvements, along with production of less directionality in properties. could be effected if the hexagonal close-packed lattice of present alloys could be replaced with a cubic lattice. In 1942, a project, having as its objective the improvement of some of the characteristics of commercial magnesium-base alloys, was initiated at Battelle Memorial Institute under the sponsorship of the Mathieson Chemical Corporation. At that time, one of the authors,* then Chief Metallurgist for the Mathieson Chemical Corporation, postulated that the addition of lithium to magnesium in sufficient quantities to change the crystal structure of the resultant alloy from a hexagonal to a body-centered cubic lattice should produce a magnesium-rich alloy which would have the desired improvements in cold-working characteristics with less directionality in properties. To test this view, a series of alloys was made and was found to have many of the attributes that were predicted. The view that magnesium-lithium alloys were of structural interest was also held by others. In 1943 and 1945, Dean and Andersonl,² obtained patents on magnesium-base alloys containing from about 1 to 10 pct lithium, from about 2 to about 10 pct manganese, and the balance substantially all magnesium; and on magnesium-base alloys containing from about 1 pct to about 10 pct lithium, from about 2 to about 10 pct manganese, from about 0.5 to 2 pct silver, and the balance substantially all magnesium. They noted that an alloy containing 83 pct magnesium, 10 pct manganese, 5 pct lithium, and 2 pct silver could be cold rolled by any of the usual methods and that this alloy was considerably harder and stronger than most other magnesium-base alloys heretofore available. In 1945, Hume-Rothery, et al.,3 predicted that magnesium-lithium base alloys should be soft and ductile and that such compositions, to which was added a third element for the purpose of producing a precipitation-hardening type of alloy, should be ductile, strong, and lighter than magnesium itself. Hume-Rothery investigated the binary magnesium-lithium and ternary magnesium-lithium-silver equilibrium relations and criticized the existing equilibrium diagrams. The binary magnesium-lithium equilibrium diagram has also been investigated by Grube, Von Zeppelin, and Bumm, Henry and Cordiano, Sal&apos;dau and Shamrai, Hof-mann,&apos; and Shamrai.8 The work of most investigators agreed with that of Grube, whose constitution diagram is shown in Fig 1. From the standpoint of development of structural alloys, the room-temperature equilibrium relations are of great interest. An examination of Fig 1 reveals that, from 0 to 5.7 pct lithium, the existing phase is alpha, which is a solution of lithium in hexagonal magnesium. The boundary between the alpha, and alpha plus beta regions, occurs at a Mg/Li of 16.5, corresponding to 5.7 pct lithium by weight. Between 5.7 pct and 10.3 pct lithium, there exists a mixture of the alpha phase (lithium dissolved in hexagonal magnesium) and the beta phase (magnesium dissolved in body-centered-cubic lithium). The boundary of the alpha plus beta and beta regions occurs at a Mg/Li of 8.7, corresponding to a lithium composition of 10.3 pct. Much of the work described here was directed toward obtaining an alloy made up of a large proportion, or entirely, of the body-centered-cubic beta structure. In his early work, Loonam found that specimens of lithium-bearing alloys were very malleable. Ingots of alloys prepared at that time were extruded to 3/8-in. diam bars, and the mechanical properties and the effects of heat treatment were then determined. These data are given in Table 1. The outstanding ductility of the alloys, combined with their moderately high strength, evoked considerable interest.

Jan 1, 1950

By Nicholas J. Grant, Klaus M. Zwilsky

EVER since the unusual high temperature creep resistance and structure stability of SAP (Sintered Aluminum Powder) and similar aluminum-alumina alloys were reported,&apos;," there has been a need to determine whether other metal-metal oxide (or other hard stable particle) alloys, not so ideal as the Al-Al 2 O 3 system, would show similar high temperature strength and stability. Of the many possible methods of obtaining a metal-metal oxide alloy,a one that offers many practical and theoretical advantages is the simple mechanical blending of metal powders with hard stable particles, followed by pressing, sintering, and hot extruding. With this purpose in mind copper powder and silica and alumina were selected for experimentation because these materials are readily available, cheap, reliable, and lend themseives te the simplest processing and testing. Starting Materials—Two sizes of electrolytically deposited copper powders were used, a —200 mesh powder referred to as A powder in this investigation and a —325 mesh powder referred to as C powder. Silica was added in the form of pure Potter&apos;s flint from which a —10µ fraction had been separated. Alumina of the a variety was used in two size ranges. The first was a —10µ fraction separated from a coarser aggregate, the second a commercial product of 0.3µ average diam manufactured by Linde Air Products. Preparation of Powders—Five-hundred gram batches of A copper with 1, 3, and 10 volume pct of each of the three oxides mentioned above were prepared, as well as C copper containing 1, 3, and 10 volume pct of —lop silica. Powders were weighed out carefully and blended by ball milling in air for 24 hr. Since this treatment resulted in surface oxidation of the copper, the charge was hydrogen reduced at 260°C for 5 hr. The next step consisted of hydrostatically compacting the powder into a shape suitable for the required hot working. For this purpose a slug about 11/2 in. in diam and 31/2 in. in length was produced by placing the mixed powders into a rubber sleeve, holding in a perforated steel canister, and rubber stoppering at the ends; the assembly was then subjected to a hydrostatic pressure of 50,000 psi. The air was evacuated from the assembly prior to pressing in order to prevent

Jan 1, 1958

By Demitri B. Shimkin

Minerals - A Key to Soviet Power, by Demitri B. Shimkin. Harvard University Press. $8.00, 452 pp., 1953. -The book is an economic evaluation of the position of the Soviet Union in respect to mineral wealth and development. Various sources are drawn upon, including the reports issued after completion of the various five year plans. The book is of considerable reference value despite the confusion which beclouds information concerning Soviet mineral progress. The theoretical study is the joint product of some of the staff of the Harvard University Russian Research Center. The author&apos;s approach to metals and nonmetals in the Soviet Union is systematic and he presents a great deal of data covering the period 1926 to 1950. Indicated weaknesses in the mineral economy are highlighted. Some considerable space is given to Soviet mineral future.

Jan 5, 1953

Geology, by O. D. Von Engeln and Kenneth E. Caster, McGraw Hill Book Co., Inc., $7.00, 730 pp., 1952.The authors desired to write a book which would supplement the work of the teacher. The effort presents the facts of historical geology as an outgrowth of the understanding of physical geology-a method in keeping with the fundamental law of geology that "present agencies and forces, acting through enormous time, have shaped the world as we see it-the law of uniformitarianism." Narrative continuity is maintained throughout the text. Each historical geology period is made distinctive, provided with an identity, and shown to have particular characteristics. Elementary Heat Power, second edition, by Harry L. Solberg, Orville C. Cromer, and Albert R. Spalding. John Wiley & Sons, 1952. $6.50, 624 pp. The authors attempt to develop an understanding of the functions, principles of construction, and actual performance of heat-power machinery as a preliminary to the study of engineering thermodynamics. Matter and energy, fuels, and combustion are considered first, followed by chapters on internal combustion engines, fuel burning equipment, and steam engineering and utilizing installations. Pumps, compressors, gas turbines and refrigeration are also dealt with.

Jan 1, 1952

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer&apos;s further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap &apos; charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73&apos; 27&apos; and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By C. L. T. Edwards

In the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on Ioo per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer&apos;s further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blastfurnace charge as good iron as that made without scrap—made with straight ore?" This question may he answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on Ioo per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. Operation with ioo PeR Cent Steel Scrap During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a Ioo per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when Ioo per cent steel turnings were charged. Except for occasional charges of nickel scale as an "cxtra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore—ore and scrap—operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from Ioo per cent scrap to the regular burden, the charge I hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap &apos; charge. The furnace employed had a hearth 16 ft. o in., bosh 22 ft. o in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter in., bosh angle 73&apos; 27&apos; and a Balrer-Neuman top, with gas-engine blowers. Analyses Range of material charged Gravel: SiO2, 64.40 to 70.54 per cent; A1203, 3.52 to 4.58; CaO, 7.27 to 9.49; MgO, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83. I

Jan 1, 1942

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30&apos; to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,&apos; in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.&apos; The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By Guillermo Hileman

In March the President approved the new oil bill, .which became effective as Law No. 12161, providing among other things a contribution or tax on all producers varying from 8 to 12 per cent payable monthly. The new regulations, for chapter VI bearing on the tax feature, of this

Jan 1, 1936

By Guillermo Hileman

In March the President approved the new oil bill, .which became effective as Law No. 12161, providing among other things a contribution or tax on all producers varying from 8 to 12 per cent payable monthly. The new regulations, for chapter VI bearing on the tax feature, of this

Jan 1, 1936

By J. Alfred Berger, O. M. Katz

Selected samples of hydrided Zr-Hf alloys were rapidly quenched to voom temperature and exrtrnined metallographically, by X-ray diffraction, and through micro hardness studies to confirm high-temperutuve data Confirming experiments sllowed that there were five phases in this Lernary system: 1) hextrgonal with lattice parameters similar to that of the initia1 Zr-Hf alloy but slightly enlarged due to dissolved hydrogen; 2) fee with properties of a brittle, intermediate, hydride compound; 3) fct with c/a crvoltnd 1.07 and which appeared as a neetilelike precipitale; 4) hexagonal, designated ?, with c/a ratio of 2.37; and 5) orthorhombic, designated X, with a = 4.67, b = 4.49, and c = 5.093 and whose tnicro-st?ruct~ival nppetrl-nnce depcncled o/i, heat lvecrt~r~ent. The tetragonrrl phase never crppeal-erl witkorct the cubic hydricle. Abpecrrtrnce of 0 and A also tlependet on the hafnium content of the zirconium. A previous paper&apos; on the Zr-Hf-H system described the thermochemical data obtained with a high-vacuum, high-sensitivity mirrogravimetric apparatus. This data presented a fairly complete picture of the phase relationships at elevated temperatures. However, it could not establish the actual crystal structures, lattice parameters, or metallographic disposition of the hydride phases. The present complementary study utilizes X-ray powder patterns along with light and electron microscopy to characterize completely the five hydrided phases found in Zr-Hf-H alloys quenched to room temperature. Crystallographic features of the zr-Hf,2,4 zr-H,5-7 and Hf-H8 systems have been summarized in Table I. Designations of a, ß, and ? were retained in the Zr-Hf-H system for the phase regions through which the pressure-composition isotherms always sloped. However, it was not firmly agreed that these were single-phase regions.&apos; In fact, the region designated y always contained a cubic as well as a tetragonal phase after quenching to -196°C. MATERIALS Preparation of the high-purity Zr-Hf alloys has been described.&apos; The four zirconium alloys which were hydrided contained 37 wt pct Hf (23 at. pct), 51 wt pct Hf (37 at. pct), 73 wt pct Hf (58 at. pct), and 91 wt pct Hf (82 at. pct), respectively. These were designated B-2, B-4, B-6, and B-8. Photomicrographs of the initial alloys showed the material to be quite clean as would be expected from the precautions exercised in producing them. However, there were a number of annealing twins but no other subgrain structure. In addition to the four original alloys, fifteen hydrided samples were observed at room temperature. Hydrogen compositions are given at the top of Tables I1 to V. APPARATUS The phases present at elevated temperatures were studied by quenching hydrided samples to room temperature by two different methods, both under vacuum: 1) fast cooling of the sample tubes of the microgravimetric apparatus1&apos;9 with flowing air and 2) rapid quenching into liquid nitrogen. The cooling rate for 1) was 750° to 250°C in 30 sec. Since the microbalance chamber was not designed to permit very rapid cooling of a hydride sample, all liquid-nitrogen quenching was done in an auxiliary experiment. The auxiliary quenching apparatus consisted of a small-bore, high-temperature furnace, a sealed SiO2 tube containing the sample, and a dewar quenching flask filled with liquid nitrogen. The hydrided sample, previously quenched in the microgravimetric reaction chamber, was placed in a platinum boat in a vacuum-degassed SiO2 tube. A zirconium wire getter and degassed SiO2 rod, to reduce the internal volume, were also in the tube. After sealing the tube under vacuum the zirconium getter was heated to absorb the last traces of gas. Only the sample was heated at the reaction temperature for the desired length of time, and then the tube dropped through the opposite end of the furnace into the dewar. A quenching rate of 200" to 400° C per sec was estimated. Analyses of samples after the auxiliary experiment also showed practically no increase in oxygen or nitrogen content from heating in the SiO2 tube. All of the samples were examined at room temperature by the X-ray powder method. The majority of the powder patterns were obtained with double nickel-filtered CuKa radiation after 8- and 16-hr exposures in an 11.48-cm-diam camera. Cobalt and chromium radiation were also used to spread out the high d value end of the Pattern. Such patterns readily identified the minor phases. NO oxide or nitride lines were found. Where sharp back-reflection lines existed it was possible to reduce the

Jan 1, 1965

By Martin Mayers

IT has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimental investigations of fuel-bed tempera-tures1-4 have not been lacking, but the absence of any theoretical back-ground has made it impossible to use the results of these tests as a basis for prediction, except in a very general way. A mathematical analysis5, based on a somewhat simplified theory of the distribution of heat in a, fuel bed, has recently been completed by the author. Even though numerical values of some of the coefficients are not. known, the calcula-tions result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calculated. The uncertainty concerning the values of the coefficients referred to above is a serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of, the coefficients. For a more extended discussion of the theory, see the A.S.M.E. paper5.

Jan 1, 1937