Search Documents

By Donald L. Katz, Jack R. Elenbaas

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By David J. Mack

THE structures and properties of the copper-aluminum alloys have been the subject of much study since the classic investigation of Carpenter and Edwards1 focused attention on the engineering utility of these alloys. It was recognized at an early date that the metallographic structures developed in the aluminum bronzes were similar to those developed in steels, both in the annealed and the rapidly cooled state. Most investigators have been concerned with the acicular, martensitic-like structure formed from the ß solid solution upon rapid quenching; the transformation of the ß under equilibrium cooling to a lamellar eutectoid having been relatively neglected. With the introduction in 1930 by Davenport and Bain2 of the isothermal transformation technique for studying eutectoidal decompositions, a new field was opened. Although an enormous amount of work has since been done on the isothermal transformation of steel, study of structurally analogous systems has been almost totally overlooked. The outstanding exception was the prize-winning paper† of Smith and Lindlief3 who investigated the decomposition of the ß phase in copper-aluminum alloys by isothermal methods. This was followed in 1934 by Wasserman's reviews of available information on analogous transformations in eutectoid alloys. Since that time no comprehensive study of isothermally transformed eutectoids analogous to steel has appeared, although many valuable contributions have been made to an understanding of the structures developed in such systems. Important papers have been published by Kurdjumow, Gridnew and co-workers, 5-17 Obinata,18,19 Greninger,20,21 and others .22.28 The work to be described in this paper was an out-growth of preliminary studies on the isothermal transformation of a eutectoid aluminum bronze, after it became apparent that the alloy under study was reacting somewhat differently than the similar alloy used by Smith and Lindlief. PRELIMINARY EXPERIMENTS The material used in this study was a high purity aluminum bronze especially prepared by Ampco Metal, Inc. It analyzed: Copper-88.o7 pct, Aluminum-11.89 Oct, Iron-0.02 pct, Manganese-0.01 pct, Others-Balance. Although some disagreement exists on the exact composition of the eutectoid, this alloy was believed to be of essentially eutectoid composition even though some pro-eutectoid* delta particles existed in the microstructure of furnace cooled specimens. Specimens transformed isothermally at temperatures slightly below the eutectoid showed relatively large amounts of pre-eutectoid delta, but as will be shown later, this results

Jan 1, 1947

By M. G. F. Söhnlein

In the earlier clays, these ores were treated by chloridizing-roasting followed by amalgamation, with satisfactory results, according to the information now available. Material from old tailing dumps from ore treated by this process, which are found at several places in the vicinity of Oruro, seldom contains more than 5 to 6 oz. of silver per ton. As ore with less than 100 oz. per ton was not treated, the extraction of silver must have been good. Reports of the operating companies published about 1890 asserted that over 90 per cent. of the silver was recovered, but in these calculations, as a rule, no allowance was made for silver lost during roasting and the figure referred only to the extraction of silvcr by amalgamation from the roasted ore.

Jan 1, 1921

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958

By JAMES SCULLY

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That subject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public attention has focussed as never before on the subject of commodity prices. To advocate stabilizing commodity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent fell by 20 per cent. Thus a price that appears stable in dollars, rose in terms of pounds sterling and fell in terms of marks and yen. Had this result been achieved as a consequence of an international effort to stabilize prices, an American would have said the effort was successful. An Englishman would have said it had failed to prevent a price rise. And a German or a Japanese consumer would have been happy to have covered his copper needs at a lower cost in terms of his own currency.

Jan 1, 1978

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

E L. DEGOLYER, our new president, though a petroleum geologist by profession, has always s been associated with mining, for soon after his birth at Greensburg, Kan., on Oct. 9, 1886, his parents moved to Joplin, and when he went, in the course of time, to the University of Oklahoma, he intended to follow his course there with another at a mining school. He became a field assistant in the U. S. Geo-logical Survey, however, while still an undergradu-ate, and after field experi- ence in Montana, Wyoming, North Dakota, Colorado and Oklahoma, he went to Mexico as geologist for the Mexican Eagle Oil Co. This was in 1909, and as a result he was unable to complete his work for his degree until 1911. In Mexico, he located the Potrero de Llaño No. 4, one of the world's largest oil wells, and also the dis- covery well in the Naran- jos pool; and the Colorado School of Mines conferred the honorary degree of : Doctor of Science on him in 1925. On his return from Mexico, he engaged in the consulting business, specializing in financial ap- praisement, the Union and Marland companies being among his clients. In 1919, he organized the Amerada Petroleum Co., with the backing of Lord Cowdray. Last year, control of the company was purchased by an American group, headed by Dillon, Read and Co. Mr. DeGolyer is n o w president of the company. He is also vice-president and general manager of the Rycade Corp, the Rycade Oil Corp., and president of the Geophysical Re-search search Corp. The l a t t e r represents the practical appli-cation of his inter-est in the use of the torsion balance in the locating of salt domes, in which he has pioneered, the Nash dome being the first oil field in America actually brought into production by these methods.

Jan 3, 1927

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of by- product materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals.

Jan 1, 1949

By H. L. Hartman

The past 15 years have seen rapid advances in the metallurgy of materials for drill machinery and bits, but rock drilling itself continues to be largely an art. Jet piercing, roller bit rotary drilling, and rotary percussion are all promising new techniques, but the percussion rock drill, still used for 90 pct of the blastholes in U. S. hard-rock mining, has undergone no major modification since pneumatic machines were first used successfully in the 1860's. This singular lack of progress stems directly from ignorance of the nature of impact failure of rock and the fundamentals of rock penetration in general. For nearly three-quarters of a century, mining engineers did not know what went on at the bottom of a drillhole. More and more, in recent years, investigators in the field have come to realize that to understand percussion drilling they must study the basic action of percussion bits penetrating rock—not the per- formances of commercial rock drills, with their many attendant variables that cannot be isolated or controlled. Using a vertical drop tester, the writer investigated the sequence of rock failure under the impact. of a simple, chisel-shaped bit when changes were made, singly, in significant variables. Results of this and other research are reported here. BASIC CONCEPTS The formation of a crater in rock under the impact blow of a bit can be observed experimentally. Directly beneath the edge of the bit the rock is crushed into fine powder; toward the sides of the crater it chips out into relatively large fragments. An explanation of these phenomena has been offered by Drilling Research Inc. on the basis of work sponsored by this organization at Battelle Memorial Institute (Ref. 1,1954, Summary, pp. 9-18). High-speed photography and force waveforms obtained from strain gages mounted on the bit near the cutting edges recorded the sequence of events in crater formation with a die-shaped or blunt, wedgc-

Jan 1, 1960

By J. C. Smock

The magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

By John H. Bell

R. B. T. KILIANI, New York, N. Y.-I wish to present some figures based upon actual observation extending over a few months time which seem to prove the author's conclusions. It is a comparison of two machines operating on the same ore, in the same plant, one taking the undersize of ½ -in. screen and the other taking the undersize of 8-mesh. Each of the machines was first operated as a pebble mill, with flint pebbles, in open circuit, then with metal pebbles in open circuit and, finally with metal pebbles in closed circuit. For the first case, the percentage of oversize on 48-mesh, Tyler screen, in the discharge, varied, in the mill taking ½ -in- feed, from 37.2 to 19.9 per cent. The second mill, taking the 8-mesh feed, had a variation in oversize on 48-mesh, from 36.8 per cent: to 0.5 per cent.; so it is seen there is considerable variation in these figures. I have computed the tons per kilowatt-day reduced through 48-mesh for each machine under each one of these conditions, giving 6 sets of figures. The first of these I called 1.0 and determined the ratio of the others to this.. In the snipe way, I figured the relative mechanical efficiency according to Kick's law, using' the figures given by Mr. Taggart in his paper, for ordinal numbers of the Tyler screens. I have also figured the efficiency in mesh-tons per horsepower according to Gates' method by plotting the screen analyses of feed and product and multiplying the area by a constant dependent on the scale used. The commercial efficiency of tons per kilowatt-day reduced through 48-mesh checks very closely with the efficiency by Rittinger's law, within 1 per cent. except in one case. By Kick's law, the efficiency checks fairly closely, within about 5 per cent., with the commercial efficiency of the mill grinding feed, but when we start to grind a finer, 8-mesh material, and especially grinding very fine; with a

Jan 4, 1917

By Donald L. Colwell

THIS is a metallurgical war. More than ever before, the mechanized forces and the air-borne warfare are deciding campaigns. Both of these are primarily dependent upon metals. There are two ways of increasing the effective supply of these metals when the demand is greater than the total over-all supply. The American custom, when a shortage of anything develops, is to get more. In the case of some nonferrous metals this has been done. For example, our potential peak output of magnesium will be almost one hundred times the prewar production. Output of aluminun has also been tremendously increased, and production of other metals is being stimulated by every possible means. Our enemies, however, have another successful method of increasing the effective supply of a material, and that is, to eliminate entirely all nonessential uses, and also to use, in essential applications, alternate materials wherever possible. Sometimes, ersatz material is inferior to the original, and consequently does not do the job as well. Often, however, it has been found superior, and many substitute items are now being used both by industry and by the military which will continue even when the original material again becomes available.

Jan 1, 1943

By George C. Stone

AS most of you probably know, Australia has had many strikes. The two places that had the worst reputation were the Broken Hill mines and Port Pirie, where the smelter was located. About four or five years ago, the smelter changed hands. The new proprietors - immediately endeavored to get on better terms with the men and made such progress in that respect that, the men came to them and said, "There is no use giving us any more money. You have just raised our pay one- bob a day, but the store-keeper and the boarding-house keeper have raised their prices. The boarding housekeeper raised our board three bob a week and the storekeeper took the rest of it and we are no better off." Learning that what the men needed most was firewood wood the company bought the wood on a tract of ground across Spencer's Gulf and- sent men over to cut it. The wood was brought to the works and given to a man to cut up. He thought he had an easy job and loafed, but when the committee representing the men discovered that his loafing added to the cost of 'the wood, it promptly disciplined him and made -him work as he had never worked before. The next question that arose was the distribution of the wood. The committee got bids from several cartmen whose prices varied from about two to five shillings. It gave the work to the next to the lowest bidder. The fact that if delivering the wood cost more, the user would have to pay for it, was an entirely new idea to the men.

Jan 1, 1920

By M. G. Corson

The iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well-known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 1.5 per cent. silicon (Fig. I). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximurn strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb, per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2..5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 1.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction. Yensen's graphs, as shown in Fig. 1, indicate also a considerable drop in strength and yield point at the same point of 2.65 per cent. Si,

By Albert Sauveur

Iron, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.' For this purpose, a cuprie solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free, from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters. which represents the same spot as that shown in Fig. 1. The fillings have been darkened while the axes remain white, the action being, therefore, the reverse of that of cupric reagents. On closer examination, under higher magnification (Fig. 3) it is found that the picrate blackens the small particles of manganese sulfide, that these are frequently surrounded by a rim of white, or relatively white, ferrite, and that both the ferrite

Jan 1, 1924

By John G. Hall

The pumping operations at the Chief mine have been unique in the respect that for many years the entire flow of water into the mine has been disposed of by pumping into natural underground " caverns" or "sinks." Volumes up to 4000 gpm have been pumped into these caverns with no apparent tendency for the caverns to fill with water, and it has never been proven that any of the water returns to the mine workings. Major pumping operations have been carried on during two periods, the first from 1918 to 1927, and the second from 1942 to the present time.

Jan 1, 1949

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By W. G. Woolf, E. R. Crutcher

The electrolytic zinc plant of the Sullivan Mining Co. is in Government Gulch, at Silver King, Shoshone County, Idaho, in the Coeur d'Alene mining district, about one mile from the Bunker Hill smelter and about three miles from Kellogg. The Sullivan Mining Co., which owns both the zinc plant and the Star mine, is itself owned jointly by the Bunker Hill & Sullivan Mining & Concentrating Co, and the Hecla Mining Company. The Tainton high-density, high-acid process is used at this plant, therefore some parts of its flowsheet differ markedly from those of electrolytic plants using the low-density process. While it is a custom plant and has treated a variety of zinc concentrates originating from various sources in a number of states, it has obtained its main supply of zinc concentrates chiefly from the zinc-bearing ores of the Coeur d'A1ene mining district, of which the principal important sources have been the Bunker Hill and Star mines. Thus the main feed has been zinc concentrates obtained from complex lead-zinc-silver ores. For the year of 1935 the concentrates had the following composition: water, 9.5 per cent; Zn, 50.6; Pb, 3.3; Fe, 9.4; S, 31.0; Cu, 0.2; insoluble, 2.9. Flowsheet The concentrates are delivered to the plant in railroad cars, which discharge into storage bins directly under the track. Bottom-dump cars are dropped directly into the bins while a slip scraper, pulled by an air tugger hoist, is used to empty box cars. There are five storage bins for concentrates, each of approximately 300 tons capacity. At the bottom of each bin there are individual belt feeders that discharge onto a common conveyor belt, which in turn discharges to another belt that carries the concentrate onto a weightometer belt for weighing. Immediately after the weighing, the crushed oversize return from the roasters is added to the load on the belt and then the ground-up sweepings, lumps and roaster cleanings. An electromagnet at the end of this conveyor removes tramp iron from the feed. The belt discharges to a set of 30 by 12-in. rolls, which break up lumps or frozen chunks of concentrate, etc. Beneath the rolls there is a screw conveyor, which conveys the roll discharge to a

Jan 1, 1937

By Edward Steidle

NOTHING stands still. We go forward or backward. As a distinct group of educators, our immediate concern is with the preparation of young men and women for participation in the mineral industries on a professional basis. I am going to have the temerity to state emphatically that for a long time as a whole we have remained in a static position. We are now confronted with the choice of advancement or retrogression. We are still in a position to make a choice and our ultimate fate will depend upon the course of action we elect to follow. Wars always have been great catalysts and social and scientific advancements mature under military stimulus in a fraction of the time normally consumed. We are now in the midst of a conflict whose duration or final effects cannot be estimated. However, the record already demonstrates that this war as never before is a mineral war in which incentive, strategy, and outcome are directly related to the distribution and utilization of minerals. The inevitable result is a drain upon our resources now reflected in our record production and a growing public consciousness of the importance of minerals in the role of human affairs. It is evident that we must seek new mineral frontiers beyond the borders of the United States and take every other precaution to forestall a "have-not" position in the world.

Jan 1, 1943