Search Documents

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By J. S. Lasater

Resu1ts of experinmental measurernents of heat capacities and thermal conductivities of some typical porous rocks are presented. Measured heat capacities agree closely with va1ues calculated front known chenlical . compositions of the rocks. On the basis of this agreement, heat capacitir.7 of fluid-satttrated rocks were calc~ililted. Therrnal conductivities of the rock samples were measured under varioits conditions of fluid saturation. From these data therrnal dif-fvsivities were calculated. A significant variation of thermal diflusivity with trnlperature is indicated. Knowledge of the thermal characteristics of fluid-bearing porous rocks has become increasingly important with the development of thermal oil-recovery processes. Reliable thermal data for petroleum reservoir rocks are not available and approximate values are generally assumed for reservoir calculations. 'The effects of temperature, pressure and fluid saturation on thermal properties of porous rocks have not been carefully studied. The purpose of the present work was to measure and report the thermal characteristics of some typical porous rocks. A group of eight sedimentary rock samples, including limestone, shale, sandstone and silt-stone, was selected for the study. Properties reported include heat capacities, thermal conductivities and thermal diffusivities. The effect of fluid saturation on these properties was also considered. Determinations of thermal properties require precise measurements which are time consuming and difficult to reduce to a routine basis. Methods have not been developed for measurement of thermal proper-ties under conditions of pressure, temperature, and fluid saturation, which may be encountered in thermal recovery processes. As one approach to these problems, some preliminary work on methods of estimating thermal properties from other more readily measurable characteristics of the rock-fluid system is reported. The samples selected for the studies were oilfield cores from within, or closely associated with oil-productive zones. Descriptions of individual samples are given in Table 1. Clay minerals present in the samples were determined by differential thermal analysis (DTA). Quartz content was estimated from DTA cooling curves. For all but the thermal conductivity tests, a representative 200-gm sample of each core was disaggregated, thoroughly extracted in diox-ane and oven dried at 100°C. The cleaned and dried sample was care- fully split into appropriate portions for the several tests. Chemical analyses of the samples were obtained to permit calculations of heat capacities by methods which are outlined later. Resuits of chenlical analyses are given in Table 2. Heat contents of the test samples were measured by a Runsen-type calorimeter. The heat content of the unknown sample is measured relative to the known heat content of platinum. The apparatus is referred to as a relative error type because of the comparative measurements, and has the advantage of canceling systematic errors. Experimental results are reproducible within 0.5 per cent. A temperature base of 298.16 K is taken for heat content measurements. Measurements were made at five temperatures (260, 440, 620, 800 and 980° F). It was necessary to preheal the sample above the maximum experimental temperature to eliminate volatile constituents. Assuming the weight loss on pre-heat, ing was mostly water, a correction to the observed heat content was made to account for the water originally present in the sample. This latter procedure was followed in the determination of calculated heat contents as will be described later. The apparatus and the method of measure-

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

Horace F. Lunt, York, Montana* :—Two years ago I visited the region described by Mr. Jennings and assisted in the examination of a somewhat similar group of deposits in the White Mesa sandstone on the Navajo Indian Reservation, 125 miles north of Flagstaff and 50 miles east of the Kaibab plateau. There, the Triassic red sandstone is less than 200 ft. thick, and is overlain by a stratum from 200 to 250 ft. thick of white sandstone, which gives the name of " White Mesa" to that locality. The white sandstone shows all phases of crossbedding in great complexity, and evidently marks a period of oscillation and subsidence of the water, or an elevation of the land, at the close of a geological epoch. The prevailing color is white or gray, but occasionally it is red. In structure, it is composed of well-worn grains of quartzsand, from which most of the cementing material has been leached out, leaving it soft and friable. Possibly the cement was ferruginous, as is indicated by occasional traces of red color. The copper-deposits consist of a replacement of the cement of one particular cross-bedded stratum of the sandstone by chrysocolla, having also at times various quantities of tenorite in grains or masses. Some specimens of the ore contain as much as 32 per cent. of copper. Generally the copper-deposits are a few hundred cubic feet in size, and no strict line of demarcation is shown between them and the surrounding sandstone, the bluish-green color of the chrysocolla gradually fading into the white of the sandstone. The ore is apparently associated with small vertical crevices or fissures. Some of the deposits show a distinct vein-structure, while others do not. The origin of the ore is not very clear. Undoubtedly the solutions, coursing through the crevices noted above, played a prominent part in its deposition, as possibly

Jan 1, 1904

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983

By R. J. Brown

Design of a submarine pipeline system is governed by many factors, one of which is the effect of transverse horizontal currents on the pipeline structure itself Although this feature alone can be of utmost importance to the life span and stability of the underwater pipeline, it is usually the least recognized, with these hydro-dynamic forces being either completely overlooked or grossly underestimated. In an attempt to supply the methods and means for stabilization of sub-marine pipelines, much capital has been spent by pipeline companies. Design criteria incorporated by these organizations extend over a broad spectrum of engineering with bases varying from pure theory to cut and dry methods. A history of numerous failures has substantiated the postulate that many of these submarine pipelines have been underdesigned from the stability standpoint. By the same token, equally as many have been excessively overdesigned with resultant excess expenditures. An attempt has been made in this paper to establish the magnitudes of these hydrodynamic forces by measuring the lateral current-induced differential pressure distribution around the periphery of the submarine pipeline. INTRODUCTION The expenditure of money for research by corporations obviously requires beneficial results to justify the investment. One of the functions of the engineer is first to make the problem known and then to provide a means of solution at the least possible cost. The initial procedure is to investigate all pertinent published technical articles on the subject to determine if this problem has been previously solved. If resolution of this problem is not obtainable, the next course of action is to evaluate through experiments these forces and their magnitudes. On the specific subject of drag and lift, the accumulation of data is provided from three separate and distinct sources: from experience, from theoreticians and through experimental observations. The experience source has proved costly with money wasted either because of underdesign and failure or excessive expenditures for overdesign, and has not been sufficient to form a definite conclusion on these hydrodynamic forces. The pure theoretician is often not completely cognizant of the situation and his works bear little adaptation to the real problem. The experimentalist has his own problems with regard to obtaining results from small-scaled models and successfully adapting them to the larger prototypes. Each method has its own advocates who diligently adhere to their own separate routes as being the only means of resolving this problem. However, a review of the various methods of analysis leads one to the conclusion that if the advantages of all three are combined, a reasonable solution to this problem can be reached. Briefly then, the problem is to obtain the magnitudes of the forces on the submarine pipeline subjected to a lateral current by investigations of previous design considerations, by a study of existing theoretica1 data and by appropriate experimentation. This paper deals mainly with obtaining experimental data and the interweaving of theoretical and experience factors for resolution of these forces. APPARATUS AND PROCEDURE These tests were performed in 1961 at Collins Construction Co.'s main office near Port Lavaca, Tex. Test equipment consisted of a steel tank 3 ft high by 4 ft wide by 40 ft long, with several pumps circulating the water through the tank via suction lines from the downstream portion of the tank and discharging from the pumps directly into the upstream end of the tank. For reduction of turbulence, a wire section was constmcted in the upstream portion and straightening vanes in the form of pipes, screens, etc., were used to reduce the vortex and eddy action in the tank (Fig. 1). A venturi was built at the test specimen for obtaining velocity sufficient to simulate actual conditions. This full-scale test was initiated to eliminate the error introduced in modeling and obtain a truer picture of forces actually encountered. Six- and 10-in. specimens were prepared by

Jan 1, 1967

By C. W. Davis, R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper. Magnetic Properties Of Magnetite And Possible Uses As A Magnetic Material Magnetite is unique among minerals for its great magnetic susceptibility, approximately one-third that of soft iron, and some magnetites are permanent magnets, or lodestones. The literature contains many measurements of magnetic properties of individual magnetite crystals, but no systematic survey of the effect of mechanical preparation and heat-treatment was available until the recent investigations of the Bureau of which included not only susceptibility but coercive force and remanence as well. For the purpose of orientation, Table 1 gives the magnetic properties of several samples of magnetite and of a few other substances3. This table indicates that when ordinary magnetite is powdered it decreases in susceptibility and increases in coercive force and remanence, approaching the properties of lodestone. The properties of lodestone are in fact probably due to the development of very large internal surface on fine grain size4.

Jan 1, 1937

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.'-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann's constant, and the vacancy formation entropy, respectively. After applying Stirling's approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling's approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling's approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By J. O. Glanville, L. H. Haley

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. In this paper, literature relating to this process as well as literature relating to the chemical treatment of coal and mineral particulates is reviewed. Some important articles are discussed and speculations made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1983

By J. A. Herrick

FOR a long time, especially in Europe, heavy pieces of forgings, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several, very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949

By R. H. B. Jones

This paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recog nizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and developmerit. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation. General Information One hundred years ago a party of surveyors, applying the principles of geophysical prospecting, discovered iron ore in the state of Michigan in the Lake Superior district. This event was officially reported as follows:' On Sept. 19 (1844) while running the east line of Town 47 North, Range 27 West, they observed by means of the solar compass remarkable variations in the direction of the needle, amounting to 87" from the normal. Ascribing this phenomenon to iron ore, they sought and found it in ledges or outcrops at several points. The solar compass referred to was invented by William A. Burt, deputy surveyor in charge of this party.2 It is used for determining the true meridian by an observation on the sun. Eight years later, on July 7, 1852, the first iron 're, consisting of 6 bbl. of Ore, was shipped from Marquette, Michigan. It was another 40 years before the first or> shipment left the Mesabi Range in Minnesota, in October 1892. It totaled 4245 tons. Fifty years later, 90 years after the original shipment, during 1942 the Lake Superior district shipped 93,495,392 gross tons of iron ore. Production came from Minnesota, Michigan, Wisconsin, and Ontario, Canada. Throughout the 90-Year period it was known that magnetic properties of most of the ore bodies, and of the iron formations in which they occur, affected the compass. This phenomenon, later to be made use of to outline areas of ground favorable for exploration, was at first a

Jan 1, 1949