Search Documents

The Sub-committee on Safety of the Industrial Organization Com-mittee of the Institute has been asked to cooperate with the National Safety Council, and has made certain recommendations to the Board of Directors of the Institute regarding ways and means of bringing about this cooperation. The National Safety Council has been in existence seven years. Its inception was at a meeting of the American Iron and Steel Electrical Engineers held in Milwaukee in 1912. The first annual congress was held in New York City in October, 1913, at which time the Council was definitely organized. Its membership now consists of nearly four thousand members, representing industrial plants, railroads, public utility companies, insurance companies, state labor commissions, Chambers of Commerce, manufacturers' organizations, etc. These members are in all states of the Union and in eleven foreign countries, and through them the National Safety Council reaches more than six million workers.

Jan 7, 1919

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is neccssary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important cornponents of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transFormation are dealt with in a highly detailed and descriptive manner in. the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilib-rium conditions of thermal treatment. The Guilletl diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts: At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. Reference may be made at this point to the efforts of Marsh5 to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encountered in traversing the nickel-steel nickel-cast-iron range under what might be called ordinary departures from equilibrium. ExperimentaT. Conditions Since the intent has been to establish structures developed under arbitrary conditions, experimental details have perhaps more than usual importance. Three of these conditions should particularly be noticed: (I) the material was cast and not subjected

Jan 1, 1942

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By J. Elmer Thomas

The evolution of the oil business is one of the great industrial romances of modern times. First used as a medicine, then as a lubricant, then as an illuminant, and finally as a motor fuel, each change in its principal usage caused large increases in consumption. Producing Successes The producing branch of the industry responded ably to the demands made upon it. Never was there a famine, rarely any threat of scarcity, and stored inventories were gradually accumulated to form comfortable working stocks. Originally an erratic and hazardous undertaking, the discovery and development of oil fields has made such strides as to classify now as a science. When storage stocks were low, production in close balance with consumption, and demand trending sharply upward, considerable concern was expressed over future needs. Price was very responsive to fluctuations in supply under those conditions, and quotations for crude and refined oils exhibited wide swings. A very different situation exists today. Consideration of the statistics only since the war will show how recent has been this change. In the 10-year period from 1918 to 1927 inclusive, we produced in the United States 6,100,000,000 bbl. of crude and imported 900,000,000 bbl., our total supply being 7,000,000,000 bbl. The consumption was 6,600,000,000 bbl., thus adding to stocks 400,000,000 bbl., an accumulation of somewhat less than 6 per cent. of the total supply. During that period virtually every field was promptly developed as soon as discovered and nearly every well in the country was producing at full capacity. With the maximum production of the wells required to take care of the rapid increases in consumption, with storage stocks moderate and proven reserves very slight, the producing division of the industry acquired a tempo not needed now. Potential Surplus Today the situation is vastly different. The economic consumption is about 2,700,000 bbl., with current production slightly in excess of that.

Jan 1, 1930

By H. Ries

THE stabilization of a gravel road with soil is a method of treatment developed in recent years by the United States Bureau of Public Roads for the purpose of binding the constituents together better, and maintain-ing a more durable surface. The process consists in adding to the gravel or crushed stone and sand, a soil mortar, so-called, of fine sand, silt and clay, mixed in the proper proportions. The coarse gravel and sand supply structural strength and hardness; the fine sand adds embedment support to the coarse sand; the silt acts as a filler to prevent the granular particles from rocking; while the clay serves not only as a binder but also provides pores minute enough to cause connecting moisture films which are supposed to have high cohesive properties1. It will be recognized that the clay is an important ingredient both when wet and dry, and should not show excessive expansion when wet, nor correspondingly high shrinkage in drying, as otherwise there is danger of unseating the nonplastic particles. Such a stabilized road, although an improvement on one with a floating surface, will in course of time be subject to wear, and become dusty when the clay dries out and breaks up. It has been found that if some salts are added to the road mixture they tend to maintain the soil moisture and prevent dustiness of the road or raveling of the road surface. In addition to this, it is claimed that these dissolved salts cause a thinning of the moisture films on the particles, thus permitting greater compaction of the road mixture, and thereby increasing its density. This fact can be proved by noting the increased compaction which a road mixture shows when certain salts are added to the soil water. Since certain chemical substances such as sodium chloride are electro-lytes, the question arises whether they cannot have some effect on. the qualities of the clay in the soil mortar, and perhaps improve them. In view of the fact that certain salts seem to exert a favorable effect on the road mixture it is desirable that they be held in the road soil as long a time as possible.

Jan 1, 1936

The Library of the above-named Societies is open from 9 A.M to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 6, 1918

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By Giovanni B. Barla, Stefan H. Boshkov

The block caving method is examined in this paper on the basis of experimental results and observations in the field, and through the use of numerical modeling by the Finite Element Method. The Grace Mine, developed by a panel caving method, served as a reference case. However, the results obtained and the simulation techniques which have been developed may find useful application in more general conditions as encountered in other mining operations by block caving. Following a brief description of the Grace Mine and of the mining method, the problems associated with the behavior of underground drifts at the production levels, during undercutting and caving, are addressed. The most important results obtained through monitoring of strains and loads in the supports of a runway are discussed, while giving relevance to the sequence of mining operations in the immediate vicinity. The most important geomechanical data, as provided for subsequent modeling, are described with reference to: (a) rock mass characterization and (b) in situ state of stress. Then, the numerical modeling procedures, developed by the Finite Element Method in order to predict the caving phenomena and the behavior of underground openings during undercutting, are discussed. Finally, an attempt is made to compare the pre- dictions of the numerical analyses with, the measurements carried out at the instrumented site. Suggestions as to how to improve the results both qualitatively and quantitatively are also given.

Jan 1, 1984

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

By W. F. Stowasser

A downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in co-operation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace.

Jan 5, 1955

THE education of adolescents to perform the duties and assume the responsibilities of maturity has been a characteristic of human society since the dawn of history. In the beginning the members of the immediate family performed this function, and in modern life they still have an important part in it. Possibly religion was the first field in which education began to be functional; young people were sent for instruction to a teacher who had a broader and deeper knowledge of the subject than was possessed by the family. It does not seem necessary for our purpose to attempt to determine how, when, or where instruction in the practical arts first began to become functional, and the brief outline which follows must suffice. The discovery and utilization of mineral substances to improve and maintain the conditions of human living is a practical art, which must have had an almost accidental origin and have been developed by empirical experiments. We do not know, nor would it be useful to try to fancy, how men first learned that they could make use of mineral substances to their benefit, but however that knowledge was initially gained it was certainly trans- mitted through instruction in the family. At fist such activities must have been merely a minor part of the making of a living, bit in time those who excelled found it better to devote them-

Jan 1, 1941

By Will Clark

HE who enters a mining claim within an Indian reservation of the United States of America acquires no rights thereby, because of the fact that the lands within such Indian reservation are not a part of the public domain, and cannot be located or acquired as mineral land. However, where such an entry is authorized as to a particular reservation by an Act of Congress, such claims as may be entered under such authorization are thereby segregated from the reservation, and the Indian title is extinguished. Under the Choctaw Constitution, any citizen of that nation, in other words any Choctaw Indian, who discovered a coal mine, acquired an exclusive right to all coal within a radius of 1 mile. The laws of the Chickasaw nation provided for the formation of corporations to develop coal and other mines, with authority to contract with others to develop and work the mines. Under these laws, leases were made; but Congress subsequently abrogated all existing leases, prohibited all persons from receiving royalties from such mines, and provided that all coal within the nation should remain the common property of the tribes. Such leases are now expressly prohibited by an Act of Congress (32 United States Statutes at Large, 655). All leases of mineral lands upon Indian reservations must now be made under regulations promulgated by the Secretary of the Interior, and the royalties must be paid into the United States Treasury for the benefit of the tribes. In Canada the Indians have no rights to the royal mines and minerals, and the government can make no stipulation with the Indians which would affect the rights of the Province in which the lands are situated. Therefore, while it is true that under our present law no rights can be acquired to a mining claim within an Indian reservation, it seems to be fully within the authority of Congress to make laws, giving such rights to mineral locators as it may deem necessary or expedient.

Jan 6, 1914

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By J. F. Stiehr, R. L. Sanford, T. L. Myers

This paper summarizes the development of a Directory of Computer Programs Applicable to US Mining Practices and Problems. The directory is funded by the US Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various US government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 9, 1979

By T. Gleason

Problems involved in applying wet scrubbers to gas cleaning coal dust from thermal dryers are reviewed. Careful consideration of all the elements going into a modem coal preparation plant is required in view of the increasing difficulty of applying suitable gas cleaning equipment. This problem arises not only from the presence of finer coals to be handled, but also from the pressures applied by both the general population and the plant operators to improve the standard of gas cleaning performance. The Peabody scrubber is presented by the author as a machine designed to help improve this cleaning operation. Wet scrubbing of fine coal from thermal dryers poses a number of problems in adapting the gas cleaning equipment to the fine particulate matter. Among them are: 1) Dust in gases leaving the thermal dryer cyclones is often extremely fine with high percentages of total dust loading less than 1p in size. 2) Flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulfur or higher. Therefore, comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3) Requirements for residual coal loadings leaving the gas scrubber are continually being lowered, while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend. 4) Installation of a scrubbing system on thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore, the operating costs of gas pressure drop and water requirements must be held to a minimum. We have, then, the basic situation which calls for comparatively high cost stainless steel alloy wet scrubbers, which must be highly effective in removing coal fines particularly in the 0 to 5-p size range. Further, the standards of scrubber performance are continually being raised towards the level where gas discharged from the scrubbers must be essentially free of any coloration due to residual dust. In view of the highly refractive nature of fine coal dust, residual loadings of 0.01 grains per cu ft or less are required to provide a color free discharge gas. In the present specifications under consideration a residual coal loading of 0.05 grains per cu ft would be considered color free, since the discharge gases are saturated in the range of 150°F. The steam plume acts as a masking agent at the point of discharge, and upon dissipation of the 150° saturated vapor stream, the effluent gas stream could be essentially color free. The specification under consideration calls for residual solids loading of 0.05 or less grains per cu ft, given a coal size distribution shown in the basic data in Table I. It is noted that the dust laden coal stream has a size distribution by weight of 33% in the 2 to 5-p size range and 55% in the 0 to 2-p size range. The particle size distribution given in the specifications does not detail the percent by weight less than 1-p in size, and more important, the size distri-

Jan 1, 1963

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer