Search Documents

By J. E. Fox Jr., J. L. Lummus, J. P. Gallus

Fresh water or brine drilling fluids may be kept free of suspended drilled solids by the addition of a water soluble acrylamide-carboxylic acid copolymer at the flowline. Addition of from .01 to 0.2 lblbbl of the polymer solution to drilling fluids containing less than 5 per cent clay solids by weight causes the solids to flocculate and settle rapidly to the bottom of the pits. Solutions of the polymer injected at the pump suction reduce the loss of water to permeable formations without impairing the permeability to oil. The use of drill-itlg fluids clarified with the polymer has resulted in increased drilling rates, extended bit life, and lower drilling fluid costs. INTRODUCTION Field experience and the results of a number of investigations have established that the accumulation of solids in drilling fluid reduces drilling rate.'-' Drilling with water makes possible higher drilling rates than can be achieved with mud but in many areas drilling with water may not be feasible because of the possibility of encountering high formation pressures or by-dratable formations. To combat these conditions, the drilling fluid must possess certain physical properties such as viscosity, density, fluid loss, etc., which require the presence of solids. The current trend in drilling fluid treatment is to maintain as low a percentage of solids as is possible without harmfully affecting the mud properties needed for drilling. Mechanical separating devices such as wet cyclones and decanting-type centrifuges are proving to be an economical means of controlling the percentage of solids and thereby maintaining low solids muds. Also: special muds have been developed for the purpose of retarding the hydration of drilled solids so that they may be more easily removed by shale shakers or settling pits. In some areas, such as West Texas, the characteristics of some formations will permit drilling with water. However, because of the dispersion of drilled solids, it is usually not possible to maintain clear water even with the aid of mechanical separators, or by utilizing large settling pits. For this reason the commonly used term "water drilling" is a misnomer since the water usually contains some solids. Because of the improved drilling rates and other benefits which might be effected, a laboratory and field study was made of the use of flocculating agents for maintaining clear water for drilling. PROCEDURE Laboratory—Solids Settling Two techniques were employed to determine the effectiveness of flocculating agents in settling solids from drilling mud. First, the rate of fall of solids was measured in graduated beakers containing mud treated with various flocculating agents. Natural gum, oil-in-water emulsions prepared with ethoxylated nonyl phenols and diesel oil. and a powdered synthetic acrylamide-carboxylic acid copolymer* (hereinafter referred to as "polymer") were tested as flocculating agents in both fresh water and salt saturated muds containing 4 per cent solids. The polymer was not added in the powder form directly to the muds but was first dissolved in water in a concentration of 3.5 lb/bbl. The polymer solution was then added directly to the mud. The concentration of the flocculating agents, including the polymer, was varied. High rates of fall of the solids indicated high flocculating efficiency. A second technique consisted of measuring the time in minutes required to obtain clear water at the pump suction after addition of the various flocculating agents at the flowline. These tests were made using a model mud circulating system having a total volume of approximately 10 gal. The natural fresh water and brine muds used contained 4 per cent solids. A sketch of the circulating system appears in Fig. 1. The circulating rate

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated'

Jan 1, 1967

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By A. Hansson, G. E. Tardiff

WHILE it is generally known that cold-worked low-and medium-carbon steels exhibit substantial increases in tensile rupture ductility with increased deformation velocity172 (up to the von Karman limit), the observations for annealed or normalized steel do not permit simple generalization. Various investigators, for example, have reported both small increases1,3 and small decreases4,5' in rupture ductility with increased rates of deformation of normalized low-carbon steel. The purpose of the present note is to report on the dependence observed for strain-aged steel since preliminary work here indicates that strain aging results in the development of a consistent type of behavior that is understandable in the light of current knowledge of the lower yield dynamics for steels which deform inhomogeneously.6 This realization throws additional light on the influences responsible for the behavior of normalized steel. The results presented here were obtained for a 0.21 pct C, 0.012 pct N sheet (0.012 in. thick) steel which was received in a temper-rolled condition (approximately 3 pct reduction in thickness after process annealing); the as-received material had a spherodized structure with a ferritic grain size of ASTM 8. The material was selected for testing after 6 months room temperature aging, at which time the static lower yield and ultimate tensile strength measured 79 and 82 kpsi, respectively. ASTM 2-in. reduced section, 1/2-in.-wide specimens were used in smooth bar tests and 3/4-in.-wide specimens containing two 60-deg opposed edge notches (root radii = 0.002 in.) were used in notched bar tests. To facilitate strain measurement, the smooth bars were blued with ink and marked at 0.1-in. intervals along the gage length; the notched

Jan 1, 1968

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company's computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

By Carl R. Christiansen, James J. Scott

Advance mine planning, coupled with good mining practice, can be employed to develop underground space in stone mines for future industrial usage. To assure the developer the maximum return on his investment, initial planning should consider all aspects of the commercial operation, including surface layout, mining, and underground industrialization. The modular concept of mining to compartmentalize the space offers several advantages over conventional methods. Some expenditures can be considered as mining costs with a reduction of profit from stone production while lowering the capital requirements for conversion for usable space.

Jan 1, 1977

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1' that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers', Fincham and Richardson,la by St Pierre and Chipman,' and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By A. E. Bellis

ROBERT J. ANDERSON, Cleveland, Ohio (communication to the Secretary *).-The paper by Messrs. Bellis and Hardy was interesting to me and has led me to make a few remarks concerning some of the points brought out. The question of employing correct hardening temperatures is one that is sadly neglected, particularly in many large plants that forge and treat their machine tools for private use. As is most aptly remarked in this paper, "The custom of using one, high-speed temperature for all tools is very poor practice;" still, such practice is more common than otherwise. An instance came to my attention some time ago, in connection with some work with the standardization of high-speed steels for machine tools, where there were no less than six different brands of alloy steels being used for machine tools such as lathe, shaper, planer, boring mill and cutters of like nature. All of these different steels received identical heat and forging treatment-or at least that was the aim of the tool hardener. That the results were highly unsatisfactory goes without saying. That the hardening department of many plants is conducted on a rule-of-thumb fashion is the reason for a great deal of the trouble and disappointment which seems to be the lot of many tool-steel users. Exceedingly crude execution is the rule rather than the exception, and it is no small wonder that the results are as good as they sometimes happen to be. It would seem that at the present price of alloy steels the subject should receive a closer scrutiny by purchasers than it does. One not familiar with the workings of souse plants that disdain to lend an ear to scientific heat treatment would scarcely give credence to some of the methods employed, not only in the treatment of the steel but also in its selection and purchase. Heating for hardening should be conducted under close pyrometric control only after the correct hardening temperature has been determined.

Jan 3, 1917