Search Documents

DAVID COLE, El Paso, Tex. (communication to the Secretary*).-I notice that Mr. Callow takes issue with me on certain points I have previously contributed to the Transactions, to which I would reply," follows: Regarding Inspiration: Mr. Callow's refinements of gravity methods made just prior to the advent of flotation in the Southwest were intended to be "down to the minute," and the gravity flow sheet for Inspiration ores which he brought out at that time as the result of his long campaign of experimentation was regarded by many as the last word in wet gravity work. It was not my intention to discredit this good work when I said "he threw small light on slime treatment." "Minus 200 mesh," however, is not-synonymous with "real slime." Repeated treatments by gravity methods will result in the separation of a very large percentage of the fine granular sulphides in sizes much finer than 200 mesh, and I gave him due credit for that. The unavoidable losses were made in the "real" slime which I mentioned in the paragraph which Mr. Callow refers to as my "statements on page 1871," and his refinements were not a solution to the real slime problem. Mr. Callow has called attention to the fact that his best results at. Inspiration in gravity work were obtained on Joe Bush ore and he presents a table, viz., Tests Nos. 68, 71, and 72; and asks us to consider and compare these results, made by his refined gravity methods, with the results obtained by 'flotation methods in the new mill "during the second half of 1915 and in August, 1916." Of course, the ore treated in the mill was what happened to come. It was not Joe Bush ore, and therefore comparisons of detail figures are of no value. In regard to Mr. Callow's statements under the caption "Callow Cells Adopted by Arizona Copper Company," I would say that those who have been sufficiently interested to read my paper and' his remarks will notice what amounts to contradictory statements on several points which I cannot allow to go unchallenged. I was on the ground constantly and got my information at first hand. The tables published were the official ones. Mr. Callow was not present during the period and has been laboring under that disadvantage.

Jan 5, 1917

THE National Safety Council will hold the following ses-sions in the Waldorf-Astoria Hotel, New York, N. Y., on Oct. 2, 3 and 4: Oct. 2. 9.30 A. M. 1. Report of past year committees, by Chairman 2. "Safety Pays," by Howard I. Young, Vice-President, American Zinc, Lead and Smelting Co., Mascot, Tenn. (Discussion) 3. Entertainment 4. "Methods and Results of Improved Foremanship Conferences," by H. A. Gilbertson, Director of Per-sonnel, Lehigh Coal and Navigation Co., Lansford, Pa. (Discussion) 5. Appointment of election and resolutions committees Oct. 3, 9.30 A. M.

Jan 9, 1928

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By Edmund C. Pechin

THE writer approaches this subject with a great deal of diffidence —first, because it is utterly impossible to treat it satisfactorily within the limits of a paper, and, secondly, because the larger development is of so comparatively a recent date as to make authoritative data on some interesting points unavailable. For over one hundred years small charcoal-fnrnaces have been in existence, at widely scattered points, making a few tons of iron daily, and then gradually increasing to a daily output of, say 10 to 12 tons, as the market widened. With the exhaustion of local supplies of wood, inaccessibility to market, and sharp competition, bringing lower prices, many were compelled from time to time to make temporary stops, and finally to cease altogether. During the first half of the century there were at different times in operation between 75 and 90 charcoal furnaces. The last Directory of the Iron and Steel Works of the United States (1890) gives 19 as the number of charcoal-stacks in Virginia. Of these several are cold, and, it is

Jan 1, 1891

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By Henry J. Sandri

The use of economic models for forecasting purposes is an inexact yet necessary tool for mineral decision making. One method not commonly used is cyclical analysis because of its "non-scientific approach". However, under certain circumstances a modified cyclical approach can provide useful insight to mining companies. The current paper discusses mineral modeling, the type of economic models and the use of cyclical forecasting for mining firms (not speculators) involved in precious metals.

Jan 1, 1984

By R. S. Wagner, C. E. Miller, H. Brown

A dc field was applied to liquid BI-Sx or Au-Ge alloys of eutectic composition. The liquid alloys were kept at a temperature slightly above the eutectic. The concentration changes due to electrodijfusion are large enough to cause nuclcation and growth of the primary phases at the respective electrodes. Nearly complete separation of Bi-Sn eutectic was obtained as well as substantial separation of Au-Ge eutectic. The effect of an electric field on the solute distrihn-tion was itluestignted itt tlirectiortally solidified rods of a dilute Bi-Sn (0.5 al. pc,t Bi) alloy. Field-freezing was carried out in small-diameter cupillay tubes to avoid cotuectice mixing -of the liquid. The relative sollcte corzcentratioi, Cs/Co , was rneusred by n radioac1il.e tracer netlod. Cs/Co can be made both largev than unity or srialler than the equilibiuwz distvibrrlion c.oejyicienl, k, , oiler a substattiul portion of the soliclifi&apos;erl rocls. A direct current, passed through a liquid-metal solution, can cause substantial concentration changes by electrodiffusion. The magnitude of the change depends on the difference in ionic mobilities of the atomic species in solution. Electrodiffusion has been studied in many binary and ternary liquid alloys.&apos;y2 It was found that the rate of material transport decreases with time for a constant applied field, as a concentration gradient is established in the solution. A steady-state concentration profile is achieved when electro-diffusion is compensated by chemical diffusion. This may seem to limit the use of electrodif fusion for metallurgical application. However, a way of utilizing the effect of electrodiffusion is to combine it with crystallization or controlled freezing. rakin was first to propose this as a new method of separating metal alloys of eutectic composition at temperatures slightly above the eutectic temperature. It was possible by this method to separate Bi-Sn and Bi-Cd eutectics into their component phases. Angus et al discussed the possibility that the effective distribution coefficient, keff, could be varied by proper application of an electric field during solidification. The combination of electrodiffusion and solidification, called field-freezing, was discussed in detail by Pfann and aner. It was shown that field-freezing can be used as a crystal-growth process, an efficient method for eutectic separation, and a new means of changing the effective distribution coefficient. k,ff, beyond the usual range of ko < k,ff < 1. The liquid layer adjacent to the solid-liquid interface can be either increased or depleted in solute due to

Jan 1, 1967

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. A. A. STEVENSON, Vice- Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A: Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson is appointed an additional Vice-Chairman of the Committee. He will serve as Acting Chairman during the absence abroad of Professor Sauveur. For the meeting of the Institute which is to be held in New York City, Oct. 16 and 17, 1913, the following papers are now assured

Jan 7, 1913

By William P. Blake

In another paper I have described in general the close association of zinc-blende and iron pyrites in the ore-deposits of southwest Wis consin. These two minerals generally occur together at the same horizon, a sheet of one being overlain by a sheet of the other; and also the pyrites is disseminated through the blende to such a degree that the latter is rendered comparatively worthless for the produc tion of spelter. Ordinarily the pyrites, which is mostly the trimetric marcasite variety, occurs in about equal quantity with the blende and is separated by hand-culliug and chipping; but there are large de posits where the ores are so closely mixed that they can neither be separated by culling nor by any mechanical method. The specific gravity of the two minerals is so nearly the same that attempts often made to effect even a partial separation by jigging have proved un. successful. The smelters of zinc-ores in the Mississippi valley will not take ores which carry more than 7 per cent. of iron; and it is therefore necessary to cull the massive (&apos;jack" with great care and at consid erable expense, in order to bring it up to the market-standard of purity. The results of trials to effect a separation of blende and pyrites in other regions have been equally unsatisfactory. The literature of this branch of metallurgy abounds in examples. In Wisconsin efforts have been made in the past to " burn " the mixed ores in heaps, in order to soften or destroy the pyrites, and facilitate its separation from the massive blende. The same method has also been resorted to when galenite is mixed through the substance of the blende, for the purpose of disintegrating the ore, so that it could be separated by jigging. The custom was to pile the ore and the fuel together. As might have been expected, the results were far from satisfactory. As is usual in heap-roast ing, some portions of the ore were overheated and decomposed; zinc was lost by volatilization; the galenite in some portions was

Jan 1, 1894

Joseph G. Butler, Jr., who represented this Institute on the American Industrial Commission to France, has presented a report to the Chairman of the Commission regarding the steel industry of France in war time. In this report Mr. Butler calls attention to the fact that only a few steel works were visited and that he thinks it probable that there are many plants in France more up-to-date than these. He noticed especially in the plants visited a dearth of labor-saving devices and not very great attention to the safety of the employees. He also noticed that the whole of the iron and steel interests in France are being used at the present time by the Government for war purposes, and he was told on good authority that the production has doubled since May, 1915. When the war is over, it is thought that France can send large quantities of iron ore from Algeria to the United States and take in return American coal to France, an interchange which would doubtless be of mutual advantage. In Mr. Butler&apos;s opinion the shortage of coal in France may be overcome to some extent by the use of water-power and by electrical processes for steel manufacture, and lie believes when the war ends France will be able to compete with other countries in exports of general iron and steel products, this trade being facilitated by the port improvements at Bordeaux and Marseilles. The French labor situation is much better than that in the United States from the standpoint of labor unions, but the wages are less and many women are now being employed to do men&apos;s work. This has a tendency to keep wages low, but is probably a war expedient only. The cooperation among manufacturers in France is at a high level and both local and national organizations exist for the discussion and voicing of trade problems. The national body which is a combination of the individual organizations is the Comite des Forges de France and it is an interesting fact that many of the members of this body are office holders under the Government, or heads of Government Committees which are organized to look after the very business in, which the individuals are engaged.

Jan 12, 1916

By W. Bonfield

The microstrain characteristics of a polycrystal-line Cu 1.9 wt pet Be precipitation-hardening alloy have been determined for various conditions of aging. The friction stress remained constant for all the conditions investigated, whereas the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-8 in. per in.) and the three-stage stress-strain curve in the microstrain region were sensitive to changes in dislocation and precipitate distribution. Correlations between the measurements of microplasticity and electron-nzicroscope observations of substructure are considered. ALTHOUGH the macroscopic mechanical properties of Cu 1.5 to 2.0 wt pet Be precipitation-harden ing alloys were established&apos; in some detail, there has been no previous investigation of the nature of microyield-ing in these alloys. This paper describes a high-sensitivity extensometer determination of microplasticity in polycrystalline Cu 1.9 wt pet Be, in which the friction stress, the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.), and the rate of strain hardening in the micro-strain region were measured for various conditions of precipitation. The structural changes accompanying aging in this alloy were examined using transmission electron microscopy, a study which differed from previous investigations as, in order to minimize grain boundary precipitation effects,&apos; the solution-treated alloy was cold-rolled to 40 pet reduction prior to aging. Hence the extent of recovery and recrystalliza-tion, as well as the variation of precipitate morphology and distribution, were assessed. From these results possible correlations between the microstrain characteristics and the observed precipitate and dislocation structure are considered. EXPERIMENTAL PROCEDURE The material investigated was a commercial copper beryllium alloy (Berylco 25), which had a com- position of 1.9 wt pet Be and 0.2 wt pet Co. The alloy was solution-treated at 800°C, quenched in water, and then cold-rolled to 40 pct reduction. Tensile specimens of gage length 1 in. and rectangular cross section of 0.18 by 0.06 in. were prepared from the solution-treated, cold-rolled material and aged for 15 min, 2, 24, and 100 hr at 315°C and 24 hr at 425°C to produce a range of precipitate structure. The hardness values associated with these conditions are listed in Table I. It can be seen that a maximum value is obtained after 2 hr at 315oC, which decreases with continued time at temperature to a minimum after 24 hr at 425°C. For comparison some as-solution-treated specimens were also aged for 2 hr at 315°C. The specimens heat-treated to a given condition were examined in two ways. First, the nature and distribution of the precipitate and dislocation structure was characterized using transmission electron microscopy. Thin foils were obtained from the specimens by electrolytic polishing in a 30 pet nitric acid-alcohol solution at -20oC, and were examined in an RCA EMU 3 electron microscope. Second, the mi-croplastic behavior of the specimens was measured with a Tuckerman strain gage, using the load-unload technique previously described2, 3 to determine the friction stress, the microscopic yield stress, and the variation of plastic microstrain with stress. RESULTS 1) Structural Changes During Aging. a) Annealing Processes. The solution-treated, cold-rolled Cu 1.9 wt pet Be had an irregular dislocation-cell structure,

Jan 1, 1968

By J. Holms Pollok

The determination of specific gravity dates from such antiquity, and the various published methods of determining it are so numerous, that one may well be skeptical as to the value of a new means of obtaining so well-known a quantity. I make no claim to any great novelty for the little device here described, the principles, though not the convenient details, of which are more or less embodied in the publications of Mr.

Jan 1, 1900

By M. Otogawa

TsunashiRo Wada, honorary member of the Institute, died at his residence, Ushigome, in Tokyo, on Dec. 20, 1920, at the age of sixty-four; he was born on March 15, 1856, at Obana in the province of Wakasa. An expert mineralogist, lithologist and geologist, he identified himself throughout his life with the development of the mining interest of this country. Perhaps the most noteworthy of his meritorious services in the public sense was the extension of the Imperial Steel Works at Yawata, anticipating the grim fate that hurled Japan. into a war with Russia in 1904. Educated in the Imperial University of Tokyo by foreign professors, he studied especially mineralogy, lithology and geology. In 1875 he was appointed assistant professor in the Imperial University of Tokyo, and in 1878 entered the service of the Home Department. From 1880 until 1893, Mr. Wada was Director of the Imperial Geological Survey of Japan, during which time he practically laid the foundation of the geological investigation work in Japan. In 1884, he made a trip to Europe by government order to attend the international Congress in Berlin, visiting en route several countries of Europe and America. While Director of the Survey, he was also, from 1880 to 1885, lecturer, and from 1885 to 1891, professor of mineralogy and lithology in the Imperial University, and, from 1889 to 1893, was Director of the Imperial Mining Bureau of Japan. In this capacity, he revised the mining laws of Japan, thus laying the foundation of Japan&apos;s mining administration. In 1894, he was again appointed lecturer in the Imperial University of Tokyo; in 1895, appointed Technical Adviser on Mines to the Imperial Household Department of Japan; and, in 1897, appointed President of the Imperial Steel Works, which was completed in 1900 with the expenditure of $10,000,000. In this capacity he did a great deal to promote the iron and. steel industry of this country. We owe him the ore-purchase contract with the Daiya iron mine in China, which remarkably facilitated the extension of the iron works in later days. The victory of the Russo-Japanese war must be said to be due to his merit in no small measure. He resigned the presidency of the Imperial Steel Works in 1901. In 1899, Mr. Wada visited America and several countries of Europe by government order; in 1902, he traveled through north and middle China doing exploration work and studying the geology of the country, accompanied by mining engineers and geologists. From 1896 to 1908, Mr. Wada was president and honorary member of

Jan 1, 1922

By M. Otogawa

TsunashiRo Wada, honorary member of the Institute, died at his residence, Ushigome, in Tokyo, on Dec. 20, 1920, at the age of sixty-four; he was born on March 15, 1856, at Obana in the province of Wakasa. An expert mineralogist, lithologist and geologist, he identified himself throughout his life with the development of the mining interest of this country. Perhaps the most noteworthy of his meritorious services in the public sense was the extension of the Imperial Steel Works at Yawata, anticipating the grim fate that hurled Japan. into a war with Russia in 1904. Educated in the Imperial University of Tokyo by foreign professors, he studied especially mineralogy, lithology and geology. In 1875 he was appointed assistant professor in the Imperial University of Tokyo, and in 1878 entered the service of the Home Department. From 1880 until 1893, Mr. Wada was Director of the Imperial Geological Survey of Japan, during which time he practically laid the foundation of the geological investigation work in Japan. In 1884, he made a trip to Europe by government order to attend the international Congress in Berlin, visiting en route several countries of Europe and America. While Director of the Survey, he was also, from 1880 to 1885, lecturer, and from 1885 to 1891, professor of mineralogy and lithology in the Imperial University, and, from 1889 to 1893, was Director of the Imperial Mining Bureau of Japan. In this capacity, he revised the mining laws of Japan, thus laying the foundation of Japan&apos;s mining administration. In 1894, he was again appointed lecturer in the Imperial University of Tokyo; in 1895, appointed Technical Adviser on Mines to the Imperial Household Department of Japan; and, in 1897, appointed President of the Imperial Steel Works, which was completed in 1900 with the expenditure of $10,000,000. In this capacity he did a great deal to promote the iron and. steel industry of this country. We owe him the ore-purchase contract with the Daiya iron mine in China, which remarkably facilitated the extension of the iron works in later days. The victory of the Russo-Japanese war must be said to be due to his merit in no small measure. He resigned the presidency of the Imperial Steel Works in 1901. In 1899, Mr. Wada visited America and several countries of Europe by government order; in 1902, he traveled through north and middle China doing exploration work and studying the geology of the country, accompanied by mining engineers and geologists. From 1896 to 1908, Mr. Wada was president and honorary member of

Jan 1, 1922

"The reduction works of the Boston & Montana Reduction department, near the north end of this dam is one of the reduction plants belonging to the Anaconda Copper Mining Company, the other being at Anaconda. These works employ about 1,100 men and have a capacity of about 3,800 tons of crude ore per day. This plant is now being remodeled to embody results of experiments and investigations which have been made with a view to more economic.al treatment of ores. A brief description of the plant as it will be after the remodelling is as follows:Concentrator Department: Consists of six units or sections, each section treating from 550 to 600 tons of crude ore per day. This department is not being. remodelled at the present time. A concentrating process, however, has been developed and partially installed in the old mill, and an experimental section embodying this concentration process has also been installed at the concentrator at Anaconda."

Jan 1, 1913

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,&apos;10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.&apos; The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

By AIME AIME

AT a joint meeting of the Tulsa Geological Society and the Mid-Continent Section of the A; I. M. E., held at Tulsa on March 21, the history of unit development in the Kettle- man Hills field was discussed. Robert C. Patterson? Super- visor for the U. S. Geological Survey at Taft, Calif., was the speaker. An abstract of some of his remarks follows: On July 1, 1923, curtailment agreement for two years was made between the operators of North Dome Kettleman and the U. S. Department of the Interior. In this it was agreed to consider a plan of unit development, or other cooperate method of developing the structure. As a result, Kettleman North Dome Association was incorporated in December, 1930, as a non-profit cooperative corporation under the laws of California. Approved in January, 1931, by California Oil and Gas Supervisor and by Secretary of Interior. On Feb. 10, 1931, it became an active organization through election of executive officers and eleven- directors. General manager chosen. Association started to function April 1, 1931. Assumed control of 10,800 acres of proved and semi-proved land, as shown in Table 1.

Jan 1, 1932

S. F. Emmons, Washington, D. C.: Mr. Malcolmson&apos;s paper on the intensely interesting deposits of the Sierra Mojada creates a strong desire to visit the region so well described. Although it is difficult to intelligently discuss a locality that one has never seen, I cannot refrain from offering some remarks in the nature of a tentative suggestion: 1. Age of Beds.—Mr. Malcolmson speaks of the enormous thickness of limestone forming the Sierra Mojada as belonging to the Carboniferous series. If this is not a typographical error, it seems that he should present some evidence for such age, for Chism,* in his previous article on the district, says the only fossils found there were said to be Cretaceous; and it is well known by the investigations of R. T. Hill and others that the great thickness of limestone in this part of Mexico is of Cretaceous age. 2. Structure of Mountains.—Mr. Malcolmson presents good reasons for thinking that the structure of the two related mountain masses (Sierra Mojada and Sierra Planchada) is not the simple anticlinal fold given by Mr. Chism&apos;s section, it being evident that there has been faulting as well as flexure. I venture to add that the facts presented by Mr. Malcolmson seem to suggest the possibility that, instead of being simply an eroded anticline, the valley between the two ranges may have been formed, in part at least, by the irregular faulting down of the intermediate block, on the surface of which the volcanic breccia had originally accumulated at a higher level. The sections of the Exploradora and the San Josh mines, in the smooth surface of the contact, with clay selvages and the occasional slickensides, certainly suggest a structural fault between the limestone and breccia. The arrangement of some of the

Jan 1, 1902