Search Documents

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951

By ALEC CROWELL

This brief summary of oil and gas developments in Alabama, Florida and Georgia has been made possible through the courtesy of Stewart J. Lloyd, Assistant State Geologist of Alabama; Herman Gunter, Director, Florida Geological Survey, and Garland Peyton, Director, Georgia Department of Mines, Mining and Geology.

Jan 1, 1946

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By F. R. Koeberlin

ABOUT thirty miles south of the port of Coquimbo, Chile, nestling in one of the western outliers of the main Andes range, lies the little mining town of Andacollo, a place whose history and traditions make up one of the most romantic pages in the life story of this southern republic. The beginning of Andacollo is shrouded in the penumbra of the pre-Columbian era, but its first mining activity probably dates from about the years 1440 to 1460. It was in the middle of the fifteenth century that the Inca Tupac-Yupanqui, grandfather of Atahualpa, conquered this part of Chile. His domain extended even as far south as the present site of Santiago, and perhaps farther, but was maintained with increasing difficulty against the fiercely independent and indomitable tribes of Araucanian Indians of the South.

Jan 1, 1938

Jan 1, 1929

By A. Beeby Thompson

FOR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippers and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure

Jan 8, 1920

By LEONARD S. AUSTIN

THE works of The Boleo Mining Co. are situated at Santa Rosalia, Lower California, on the opposite side of the Gulf of California from Guaymas, the, nearest railroad town. The copper deposits were discovered in 1868, and the name Boleo arose from the fact that the ore particles were agglomerated as little balls of carbonate or oxychlorides of copper. When worked on. a small scale, only ore carrying 20 to 25 per cent copper was mined; this was shipped to Europe for reduction In 1884 The Boleo Mining Co. was organized and,-the mine put in condition. Even then, due to the low price of copper, only the richer ore continued to be shipped. To operate the mine successfully the company made radical changes in the methods of development and spent money freely for construction of adequate plants for the treatment of low-grade ore. Finally, the owners of the various adjacent mining claims combined their interests and formed a joint enterprise attractive to French capital.

Jan 1, 1929

By Richard P. Rothwell

In January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it mas impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of .obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

By J. C. Fisher

Nucleation theory is applied to martensite nucleation in substitutional iron alloys. Composition fluctuations are neglected, and a steady rate of nucleation is predicted for any composition and temperature. The maximum rate of nucleation (as a function of temperature) is shown to be measurable only for on extremely narrow composition range, being too great or too small outside this range. A number of experimental observations, including completely isothermal transformation in some alloys and composition-dependence of M. temperature in others, are compared with the calculated behavior. IN a previous report,¹ nucleation theory was applied to the formation of isothermal martensite in an Fe-Ni-Mn alloy. The experimental observations of Cech and Hollomon² were accounted for quantitatively. It now is of interest to examine the predictions of nucleation theory with respect to martensite transformation in substitutional iron alloys of other compositions. Since Fe-Ni alloys have received considerable attention, both as to their transformation kinetics and their free energies, they will be treated in detail, although the results apply with equal validity to other substitutional alloys. In substitutional alloys, where composition fluctuations can be neglected in volumes of critical nuclear size, the rate of nucleation of martensite in subcooled austenite is¹ n - Nv exp (—W*/kT) [I] where the free energy of formation of the critical size nucleus is W* = 8192 p (?² s³) [2] In the expressions for n and W*, the symbols have the following meanings: N is the number of atoms per unit volume; v, the atomic vibration frequency; 8, a function of the elastic constants of austenite and the shear angle of martensite; , the austenite/mar-tensite inter facial free energy; and ?fc is the free energy change per unit volume accompanying the transformation. Jones and Pumphrey² have determined the austenite to martensite free energy change as a function of nickel content and temperature for Fe-Ni alloys. Their expression is ?F = 2500 C + 1.25 (1 —C)?FFc cal per mol [3] where C is the atom fraction of nickel, and ?Ffe is the free energy change per unit volume for pure iron as tabulated by Zener4 (or, equivalently, Fisher"). From Eqs. 1 to 3, it is possible to calculate isothermal nucleation rates as a function of temperature and composition for Fe-Ni alloys. The only unknown parameter is (?² s³). The best value of this parameter for Fe-Ni alloys, determined from M. temperatures in a manner to be described shortly, is (?² s³)= 9.92 (10)21 cgs units [4] Taking this value of (?² s³), C-curves for isothermal nucleation were calculated for Fe-Ni alloys of several compositions, and are plotted in Fig. 1. It is evident from Fig. 1 that completely isothermal nucleation of martensite in Fe-Ni alloys can be observed experimentally for only a very narrow range of compositions. Cech and Hollomon find that a nucleation rate of about 10' nuclei per cc per sec is as fast as they can follow dilatometrically, and a rate of about 10-1 nucleus per cc per sec is about the slowest that can be measured conveniently. If the nucleation rate is to lie between the limits 10-1 10 the nickel content of an Fe-Ni alloy must fall in the atomic fraction range 0.299 5 C 5 0.302. Nickel contents lower than 0.299 correspond to nucleation rates too great to follow, and those higher than 0.302 to nucleation rates too slow to measure in a reasonable time.* In view of the narrow corn- position range in which successful isothermal measurements can be made, it is not surprising that only one substitutional alloy has been described' that comes close to being in the proper range.

Jan 1, 1954

By R. J. Cowan

IN the art of cementation a controversy has been going on for years as to whether solid or gaseous carbon is the active agent in carburizing steel. More recently opinion has crystallized into a compromise to the effect that carburizing is a gaseous cementation of steel in the presence of solid carbon. The importance of this theory has a particular bearing upon the work to be described. In the art of carburizing, use is commonly made of such words as "catalytic," "atomic," "nascent" and "activated;" in an attempt to describe the process. These words are used indiscriminately. For, instance, the gas is said to be "catalytic" and carbon to be "nascent," or vice versa. In using these expressions, investigators are confirming the acceptance in their minds of the active conditions of both gas and carbon in the cementation process.

Jan 1, 1931

By H. P. Croft

[ ] Professor Hibbard's paper presents a very interesting theory concerning the influence of texture on the tendency of brass tube to stress-corrosion crack. I should like to present the result of some work done in 1941 which may throw further light on the subject. In the first place, in regard to his review of the influences of grain boundaries, we not only confirmed the findings which he quoted, but also were unable to crack single crystals of beta brass in the standard mercurous nitrate test in 50 hr under loads up to 18,500 psi. Samples containing two or more crystals of beta brass always cracked at grain boundaries and generally followed the same pattern as for alpha brass, although cracking occurred sooner than in alpha brass under the same conditions. Such a specimen is shown in Fig 4. Second, at the possible risk of repetition, we should like to call attention to the reported role of grain size as influencing the tendency to stress-corrosion crack. This phenomenon, originally mentioned by Dr. Allan Morris in the Transactions, AIME, 1931, is illustrated in Fig 5, showing the effect of variations in grain size on the tendency of drawn brass wires to crack under load in the mercurous nitrate solution. This was taken from my work published in Proceedings A.S.T.M. 41, (1941), 905.

Jan 1, 1948

By E. C. Harder, E. W. Greig

Bauxite is known mainly as the ore from which aluminum is smelted but it has large use also in the manufacture of artificial abrasives and in the production of a number of useful chemicals as well as of aluminous cement "ciment fondu." An important and growing use is in the manufacture of refractory products. Composition Dana and earlier mineralogists gave the mineral formula of bauxite as A1203.21120 and the composition as A1202, 73.9 pct; H2O, 26.1 pct. A specific mineral of this composition has, however, never been identified by either microscopic, chemical or X ray examination, and therefore it is concluded that bauxite is a rock consisting of one or more aluminum minerals together with impurities. The term is now used synonymously with aluminum ore and it embraces gibbsite (hydrargillite or alpha trihydrate), A1203. 3H20 (A1203, 65.4 pct; H2O, 34.6 pct); boehmite (alpha monohydrate), A1203•H20 (A1202, 85 pct; H2O, 15 pct) ; diaspore (beta monohydrate), A1203•H20 (A1203, 85 pct; H2O, 15 pct), and mixtures in various proportions of any two of them. Bauxite of the Mediterranean region in Europe is predominantly boehmite, as in France and Istria, subordinately a mixture of gibbsite and boehmite, as in Dalmatia, or of boehmite (or gibbsite) and diaspore, as in Greece. The bauxite of North and South America, tropical Africa, Asia, and Australasia consists largely of gibbsite, but boehmite in appreciable amount occurs in many places. Corundum (A1202) is not included un¬der bauxite, although gradations from bauxite to emery or corundum exist. All bauxite, irrespective of the aluminum minerals composing it, contains certain impurities in variable amount, including silica in the form of clay minerals (kaolinite, halloy site, and others) or quartz, iron oxide (as hematite or goethite), titania (as leucoxene or rutile), iron sulfide (as pyrite or marcasite), iron carbonate (siderite), and calcium carbonate (as calcite); the last three mentioned in minor amount and of local occurrence only. Bauxite belongs to a group of partly consolidated materials called laterites, formed by surface weathering. This group includes also impure siliceous, ferruginous, and phosphatic bauxite and siliceous and aluminous iron ores and manganese ores and nickel and chrome laterites. Phosphorus and manganese minerals locally form important impurities in bauxite deposits. Properties Gibbsite is white or light shades of gray, cream or pink. Its hardness is 2.5 to 3.5; specific gravity, 2.3 to 2.4; crystal system, monoclinic, crystals tabular parallel to 001, often fibrous, concretionary, stalactitic; luster, vitreous to pearly; generally translucent; cleavage, parallel to 001; disassociation temperature, approximately 300°C. Boehmite, a relatively new and important mineral described by J. Boehm15 in 1925, confirmed and named by J. de Lapparen64 in 1930, has some properties not yet definitely determined. It occurs in grayish, brownish, and reddish shades. Its hardness is between that of gibbsite and diaspore; specific gravity, 3.01 to

Jan 1, 1960

By H. Rush Spedden, A. M. Gaudin

IN the belief that a critical study of its operating problems might be a sound investment, the Cuban American Manganese Corporation initiated an ore-treatment research in cooperation with the Massachusetts Institute of Technology. One of the early objectives of this research naturally became the relationship of the microscopy of the Cuban ores of the Corporation to their flotation treatment. The operations in Cuba have already been described by F. S. Norcross, Jr.7 and the laboratory study of manganese oxide flotation goes back a number of years .4 Broadly speaking, the difficulties encountered in the flotation of manganese ores are that the consumption of reagents is extremely high, the concentrate contains more silica than is desirable and the tailing losses are relatively high. An appreciable betterment on any of these scores would achieve a definite betterment in costs, quantity of minable ores, and quality of product. The microscope study discussed in this paper was made on samples from the Quinto mine, from the Ponupo mine, and from mill products at various stages of passage of the ore through the mill. The writers have had access to Company records and in particular to the petro¬graphic studies made on thin sections of ore by the late Professors R. J. Colony and Philip Krieger, of Columbia University. They acknowledge their debt to both of these men for the help derived from the reports. Manganese oxides are black, friable, smudging. It is, therefore, very difficult to judge operations by inspection. The mineralogy of manganese compounds seems to be confused, and the authors believe that many more minerals have been described than actually exist. Much of this difficulty is due to the prevalence of the structural conditions that will be discussed further in this paper; namely, the porosity and the friability of the ores, and the extremely intimate association of minute manganiferous mineral crystals with impurities of various sorts. By all odds the most important manganese mineral in Cuba is the one that in this paper is called "psilomelane." The name "psilomelane" has been used in so many different ways that the choice of it for this ore may not be approved by all. However, it seems to be the best under the circumstances. This mineral accounts for about 97 per cent of the manganese in the ores of the Quinto and Ponupo mines and in the mill feed. The remaining odd 3 per cent consists mostly of pyrolusite together with minor amounts of other manganese oxide minerals. DESCRIPTION OF PSILOMELANE Aggregate Structure In grains or lumps, psilomelane has a characteristic fibrous appearance and seems

Jan 1, 1942

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

Prospectors were digging silver in the Ray mine area in 1873, and by 1880 high-grade copper ore was feeding a 30-ton copper furnace. In 1910, D. C. Jackling and his associates organized the Ray Consolidated Copper Company, known in mining circles as Ray Con, to exploit the Ray orebody. For 50 years, all mining was underground and the Ray mine was known the world over for innovations in mining methods. It was the first to mine important tonnage (8,000 tpd) by block caving methods. The mill at Hayden, 26 miles (41.6 km) from the mine, kept pace with the new mining methods developed at Ray and in the early 1920&apos;s flotation replaced gravity concentration by the vanner machines. First mining by open pit methods began in 1950 and in January 1955 all underground mining was discontinued. The new primary crushing plant, installed in early 1967, featured design simplicity with a low capital cost. The 54 in. gyratory crusher was installed within a total height of 6 1 ft (18.65 m) from the truck dump road bed to the floor beneath the feeder-conveyor under the surge pocket. The crusher is fed by 120-ton trucks dumping from one side only into a 200-ton hopper equipped with a horizontal splitter bar to protect the crusher spider. The crushed ore pocket, of 120 -ton live capacity underneath the crusher, discharges to a 0 to 200 fpm (61.2 mpm), variable-speed, 72 in. by 80 ft long (1.83 m by 24.4 m) sloped belt feeder, probably a first in the industry. Wood-picking stations are provided on either side of the belt so that old mine timbers and tramp iron can be removed from the crushed ore and the wood can be dropped into Dempster containers located below the belt. Counter-weighted finger gates control the bed depth on the belt at 14 in. (356 mm) and a low- level radiation unit automatically maintains a minimum of a 3 ft bed (900 mm) of material on the belt directly under the surge pocket. The conveyor is skirted for its full length and is approximately 60 in. (1.52 m) wide inside its metal skirt liners. Ten impact idlers at 12 in. (305 mm) spacing are provided under the loading pocket and remaining idlers are spaced at 18 in. (457 mm). The belt is 1 ¼ in. (31. 8 mm) thick; and, while it has occasionally been damaged by tramp material, belt life averages 11 million tons. When the belt is changed, the coiled new belt is lowered into position onto one of two belt stands mounted over the feeder, the old belt is cut, and one end is attached temporarily to the new belt. The other end of

Jan 1, 1978

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

Page The Cobaltchromium Binary System (paper by A. R. Elsea, A. B. \Yesterman, and G. K. Manning, Met. Tech. June, 1948, Mechanism of Precipitation in a Permanent Magnet Alloy (paper by A. H. Geisler and J. B. Newkirk, Met. Tech. Aug. 1948, Tp 2444)................................................................................................. 300 Some Effects of Applied Stresses on Precipitation Phenomena (~aper by W. L. Finlay and W. R. Hibbard, Jr., Met. Tech. Sept. 1948, Tp 2470)....................................................................................... 301 Diffusion of Carbon in Austenite with a Discontinuity in Composition (paper by L. S. Darken, Met. Tech. Sept. 1948, TP 2443) 304 An Electron Diffraction Study of Oxide Films Formed on Nickelchromium Alloys (paper by J. W. Hickman and E. A. Gul- bramen, Met. Tech. June 1948, Tp 2372)..................................................................... 305 An Electron Diffraction Study of Oxide Films Formed on Copper-nickel Alloys at Elevated Temperatures (paper by J. W. Hickman and E. A. Gulbransen, Met. Tech. June 1948, TP 2391)................................................ 307 Decarburization of Chrome Nickel Alloys by Their Surface Oxides in High Vacua and at Elevated Temperatures (paper by E. A. Gulbransen, W. S. Wysong, and K. Andrew, Met. Tech. Sept. 1948, TP 2438)................................ 307 Fractographic Study of Cast Molybdenum (paper by C. A. Zapffe, F. K. Landgraf and C. 0. Worden, Met. Tech. Aug. 1948, TP 2421)................................................................................................. 308 Effect of Composition on Grain Growth in Aluminum-magnesium Solid Solutions (paper by L. J. Demer and P. A. Beck. Met. Tech. June 1948, TP 2374)............................................................................. 309 Effect of a Dispersed Phase on Grain Growth in Al-Mn Alloys (paper by P. A. Beck, M. L. Holzworth and P. Sperry, Met. Tech. Sept. 1948, TP 2475)................................................................................. 310 Statistical Rate Theory of Metals—Mechanism of Flow and Application to Tensile Properties (paper by J. W. Fredrickson and H. Eyring, Met. Tech. Aug. 1948, TP 2423)............................................................... 315 Nucleation of Slip Bands (paper by J. G. Leschen, R. P. Carreker, and J. H. Hollomon, Met. Tech. Sept. 1948, TP 2476) and.. 318 Transient Plastic Deformation (paper by R. P. Carreker, J. G. Leschen, and J. D. Lubahn, Met. Tech. Sept. 1948, TP 2477).. 318 Plastic Deformation of Large Grained Copper Specimens (paper by W. R. Hibbard, Jr., Met. Tech. Sept. 1948, TP 2469). ... 323 Plastic Flow in Anisotropic Sheet Steel (paper by L. R. Jackson, K. F. Smith, and W. T. Lankford, Met. Tech. Aug. 1948, TP 2440)................................................................................................. 323 The Effect of Thermal-mechanical History on the Strain Hardening of Metals (paper by J. E. Dorn, A. Goldberg, and T. E. Tietz, Met. Tech. Sept. l948, TP 2445)....................................................................... 325 The Room and Elevated Temperature Properties of Some Sand Cast Magnesium-base Alloys Containing Zinc (paper by T. E. Leontis, Met. Tech. June 1948, TP 2371)..............................................................., 327 The Low Temperature Properties of Tin and Tin-lead Alloys (paper by H. S. Kalish and F. J. Dunkerley, Met. Tech. Sept. 1948, TP 2442)............................................................................................335 Thermal and Electrical Properties of Ductile Titanium (paper by E. S. Greiner and W. C. Ellis, Met. Tech. Sept. 1948, TP 2466).................................................................................................... 335 Property Changes during Aging (paper by A. H. Geisler, Met. Tech. Aug. 1948, TP 2436)............................... 337 Factors Affecting the Tensile Notch Sensitivity of Magnesium Alloy Extrusions (paper by I. Cornet, Met. Tech. Aug. 1948, TP 2419)................................................................................................. 338 Effect of Grain Size on Tensile Strength, Elongation and Endurance Limit of Deep Drawing Brass (paper by H. L. Walker and W. J. Craig, Met. Tech. Sept. 1948, TP 2478)............................................................. 339 A Copper-base Alloy Containing Iron as a High-strength, Highconductivity Wire Material (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Met. Tech. Aug. 1948, TP 2422).............................................. 340 A High Strength-High Conductivity Copper-silver Alloy Wire (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Mel. Tech. June 1948, TP 2366)...................................................................... 340 The Effect of Chronlium on the Ma Point (paper by J. B. Bassett and E. S. Rowland, Met. Tech. Aug. 1948, TP 2417.... 341 The Kappa Eutectoid Transformation in the Copper-silicon System (paper by W. R. Hibbard, Jr., G. H. Eichelman, Jr., and W. P. Saunders, Met. Tech. Sept. 1948, TP 2441).............................................................. 343 Stabilization of the Ausknite-martensite Transformation (paper by W. R. Harris, Jr. and M. Cohen, Met. Tech. Sept. 1948, TP 2446)................................................................................................ 344 Secondary Hardening of Tempered Martensitic Alloy Steel (paper by W. Crafts and J. L. Lamont. Mel. Tech. Sept. 194,8, TP 2439)................................................................................................. 345

Jan 1, 1950