Search Documents

By J. C. Deppe

A method is presented for calculating approximate injection rates in secondary recovery operations. The method can be applied to cases of unequal fluid mobilities, irregular well patterns and boundary patterns. The steady-state pressure distributions for the four flood patterns reported by Muskat and for five additional patterns reveal that most of the difference in pressure between the injection and producing wells occurs in regions around the wells which can adequately be described as regions of radial flow. This leads to a method of calculating injectivity by approximating the flood pattern with radial flow elements (or a combination of radial- and linear-flow elements for some patterns such as the direct line drive). Irregular and boundary patterns can also be approximated by radial and linear elements. Each of these elements can be described by radial-and linear-flow equations and the results combined as series flow resistances to give an approximate equation for the initial injection rate. The mobility ratio does not affect the initial rate; therefore, if the well pattern is one of those regular patterns for which theoretical rate equations have been derived for unity mobility ratio, the approximate initial rate equation can be improved by adjusting it to match the theoretical equation. The available theoretical rate equations are listed, including five new cases. As the flood progresses, the injectivity changes because in general the flood front will divide the pattern into areas of different fluid mobilities. Simple shapes can be assumed for the flood front so that both areas can be divided into radial- and linear-flow elements. Radial- and linear-flow equations are applied to these elements to account for the change in flow resistance behind the front. To calculate injection rates after breakthrough, it is necessary to know the sweep efficiency at breakthrough. Areal sweep data are available in the literature for a number of patterns, and sufficiently accurate breakthrough sweep efficiency can be estimated from these data if it is not otherwise available. Again, simple shapes for the flood front can be assumed after breakthrough, and injection rates can be calculated for the remainder of the flood. When areal sweep data are available, these data can be used to cbeck. the calculated injection rates after breakthrough. Injection rates calculated by this approximate method compare favorably with available model data. INTRODUCTION When the fluid mobilities in the swept and un swept regions are equal, the injectivity will not change as the flood front advances; and for regular patterns it can be calculated by mathematical formu1as.l When the fluid mobilities in the swept and unswept regions are not equal, the injectivity will increase or decrease as the flood front advances. In this case, the injectivity has not been calculated by analytical means for any practical well pattern; and, furthermore, scale model and analog4,6 results have been published only for the five-spot pattern. The main object of this paper is to present an approximace method for calculating injectivity for the case of unequal mobilities. The method can be applied to regular, irregular and boundary patterns. Before the approximate method is discussed, the analytical formulas for equal mobilities will be summarized, and the analytical solution for radial flow with unequal mobilities will be used to show how the injectivity changes as the flood progresses. EQUAL MOBILITIES, REGULAR PATTERNS In a flooding operation the injectivity, the rate at which fluid can be injected per unit difference in pressure between injection and producing wells, depends on basic physical properties and, in addition, on three variables to be treated here—the area of the swept region, the fluid mobilities in the swept and unswept regions, and the well geometry (pattern,

By R. B. Woodworth

Discussion of the paper of R. B. Woodworth, presented at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2247 to 2312. R. B. WOODWORTH, Pittsburgh, Pa.-This is a very long paper. It is a structural engineer's contribution to the art of mining and is written from his standpoint rather than from that of the mining engineer, and is, therefore, a study in the development of drilling structures by one who has made it his business to design structures rather than mechanism and machinery and rather than to utilize those structures in the actual exploitation of oil and gas. Drilling practice varies widely in different oil and gas fields. The , problems of western Pennsylvania are much simpler than the problems of the Mid-Continent and of the Gulf Coastal Plain and these again are simpler than problems of the Pacific Coast. The history of the commercial development of oil and gas is recorded in the annual publications of the U. S. Geological Survey and other bodies whose business it is to make record of statistics. The mechanical and structural features of the art of drilling have not yet received adequate treatment by the historian. Scattered references may be found on the subject in almost any work dealing at large with petroleum and its production. These references, however, are to those particular aspects of the matter that were contemporary with the publications themselves, but so far as I am aware there is no continuous and comprehensive account written of the development of drilling structures from their beginnings down to the present time, and certainly the more modern application of steel in the construction of such structures has not previously had an adequate discussion. With this latter phase of the subject I have been intimately associated, indeed, taking to myself the credit for having, in a way, been responsible more than any one else in the United States for the application of steel in the manufacture of drilling structures, and the purpose of the paper which is now before you is to record particularly the steps in that development while the subject is still fresh and the data available.

Jan 5, 1916

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

The Enquirer of October 13, 1835 carried a letter signed "G," calling attention to the great number of Virginians who were leaving the state and to the lack of enterprise shown in not developing the ample natural resources available. He mentioned coal in particular and in closing said: "Besides the coal mines owned by individuals, the Black Heath company of colliers are carrying on extensive operations. Owing to the derangement of the currency, and the immense expenses incurred in boring and sinking new shafts, I understand that their dividends have not yet been so large, as they may be confidently expected in future.-Another company, under the title of the Midlothian Coal Mining Company, is now about being organized by the Messrs. Wooldridges of Chesterfield, for the purpose of establishing an extensive coal business. Having examined the lands embraced in the charter and the principles upon which the company is designed to be organized, I am persuaded that more productive stock can no where be found. The charter embraces a space nearly equal to a mile square, adjoining the mines of the Black Heath company, those of Mr. N. Mills, and those of Stone Henge, which space must contain coal of great thickness of excellent quality, as the strata of coal of those other mines pass through it; exhibiting a field so extensive, that centuries may elapse before it is exhausted. A shaft has been sunk on these lands, from which a very large quantity of the best coal is being raised. The terms of the charter require the Proprietors to sell one-half of these lands and mines, from the sale of which they will appropriate $100,000 as permanent capital, to purchase hands and engines, and to sink other shafts to work the property and thus going into operation with such decided advantages, as to produce a profit as great as a reasonable man should desire. Here is an opportunity for investing capital, which I think should satisfy the wishes of many Virginians who speak of emigrating. Will they not embrace it?-I have confined my remarks to the coal mines, because they are in the heart of our State, and their operations are familiar to many who can verify the statements. I might extend them to the other mineral treasures of our State; but if I do so, they must be reserved for another number, this being longer than I intended, and perhaps longer than you can conveniently find room for in your crowded columns. G." In January 1828 the Tuckahoe Canal Company was authorized to construct a canal along Tuckahoe Creek, from the James River up the stream about five miles; later this was amended to allow the use of the stream with a depth of water of two feet, no tow path was required, or provided: A toll of one cent per bushel was collected and the canal company made large profits. The service was so poor that in December 18, 1835, John G.,

Jan 1, 1942

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By George Kunz

(Butte Meeting, August, 1913.) THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World&apos;s Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely clue the eventual success of this eminently desirable reform, which lie has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3

Jan 7, 1913

Discussions of the papers of DORSET A. LYON and SAMUEL S. ARENTZ, RICHARD D. DIVINE, H. A. WENTWORTH, and S. E. BRETHERTON, presented at the Salt Lake meeting August, 1914, and printed in Bulletins Nos. 91 and 92, July and August, 1914. GEORGE W. RITER, Salt Lake City, Utah.-We have every reason to believe that oil flotation Will soon come into general use as a final guard against slimes losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, anti precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah¬the old Eureka Hill property-where ores that were too low in value to Warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble.

Jan 11, 1914

By D. N. Seidrnan

In the present note we present thermal-analysis data for the liquidus curve from 0 to 76 at. pct Se and for the selenium-rich monotectic reaction in the Pb-Se system. We have previously reported that no expey-imental eviderzce was found for a lead-rich monotectic reaction, at -860°C with a monotectic composition of -20.5 at. pct Se, as found by Nozato and Igaki.&apos; Our additional data substantiated this earlier finding and extended the composition range studied. The alloys were prepared from semiconductor -grade lead and selenium purchased from the American Smelting and Refining Co. Both elements were 99.999+ wt pct pure as determined by the supplier. The impurities for lead were Fe (1 ppm) and Cu & ppm) while for selenium the impurities were Cu (< 1 ppm), As (< 1 ppm), Te (1 ppm), and C1 (<1 ppm). The general procedures used for thermal analysis were those specified by the National Bureau of Standards. A Pt/Pt-10 pct Rh thermocouple calibrated against the freezing points of zinc and copper purchased from the National Bureau of Standards and antimony (99.985 pct pure) purchased from A. D. Mackay, New York, was used for all the thermal analysis. The thermocouple electromotive force was measured with a Rubicon Type B potentiometer used in conjunction with a galvanometer with a sensitivity of 0.5 pV (mm) -&apos;. The absolute accuracy of this thermal-analysis system was *0.5"C. One-hundred-gram alloys of the desired composition were sealed in quartz crucibles, with a central thermocouple well, at a pressure of less than 10"1 Torr. The alloys were initially heated well above the liquidus curve and shaken vigorously to insure homogeneity. Cooling curves were then taken by the direct method at cooling rates ranging from -0.5" to 1.5"C (min)-&apos;. The phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis is shown in Fig. l.* An extrapolation of the selenium-rich portion of the liquidus curve to the monotectic reaction isotherm (678.3"C) gave a value of 76.1 at. pct Se for the monotectic composition. A tabulation of all the thermal-analysis data is given in Table I. As we previously reported no experimental evidence was found Fig. l—The partial Pb-Se phase diagram from 0 to 76 at. pct Se as determined by direct thermal analysis. For the sake of clarity the points for the 49.00 and 49.16 at. pct Se alloys were not drawn on this phase diagram, see Table I. for the lead-rich monotectic reaction found by Nozato and Igaki.&apos; This result was further substantiated by the fact that none of twelve lead-rich alloys, see Table I, examined for this monotectic reaction exhibited a thermal arrest in the temperature range (849" to 863°C) cited by Nozato and Igaki for the lead-rich monotectic reaction. Hence, our results tend to support the earlier qualitative work of ~elabon&apos; and Friedrich and ~eroux" in the 0 to 50 at. pct portion of the phase diagram, though the selenium-rich monotectic composition and reaction isotherm temperature were in agreement with the approximate values (75 at. pct Se and 672" to 680°C) given by Nozato and ~~aki. &apos;

Jan 1, 1967

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain&apos; introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?&apos; nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?&apos; are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By Alfred G. Heggem

It is the purpose of this article to describe methods recently introduced into the oil and natural gas industry to safeguard the lives of the workmen and to protect property from destruction. Only such drilling methods are described as pertain directly to the operations necessary to maintain the well under complete control at all times. Wells Formerly Drilled Without Controlling Equipment It may seem incredible that practically all wells, until rkcently, were drilled without the provision of any means for control. To drill a hole into a boiler carrying high-pressure steam without first providing means to control the escape of steam would be unthinkable, yet in oil fields wells are drilled into a gas or oil formation with a possible pressure of 300 to 1,800 lb. per square inch and a daily flow of 20,000,000 to 80,000,000 cu. ft. of gas or 1,000 to 15,000 bbl. of oil per day. Some wells have produced in excess of 100,000 bbl. of oil per day, but these are exceptional cases. In addition to the loss of product, one must consider the great danger attendant upon the promiscuous liberation of such an amount of explosive and inflammable substance. Introduction of Metal Casing for Deep Drilling The introduction of metal casing to secure a permanent and impervious wall in a well made the drilling of deep wells possible and removed many of the original problems encountered in well drilling, but it did not insure the control of the well. To obtain the full value of the casing it was essential that a pressure-tight joint be made between the wall of the well and the lower end of the casing. Many materials in various forms were used, including cotton, hemp, stable refuse, oats, rice, cloth, leather, cork, rubber, lead, clay and cement, resulting, after a slow process of evolution, in the general adoption of two types of bottom fittings for

Jan 1, 1916

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale&apos; defines clay as material finer than approximately 4 microns. Grim&apos; has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

By R. D. Daniels, T. W. Wood

The tensile properties of columbium and Cb-H alloys containing up to 455 ppm H were studied as a function of temperature and strain rate. Hydrogen, introduced into columbium at elevated temperatures, using a thermal -equilibrium technique, embrittled columbium most severely at about —77°C. This elnbrittle ment occurred even at hydrogen concentrations of an order of 20 ppm. At higher temperatures, the hydrogen tolerance of columbium increased in relation to the increased solubility of hydrogen in tile metal. Below this temperature hydrogen tolerance, as determined by ductility and fracture stress, increased slightly. Strain rate had little effect on the tensile results for cross-head speeds over the range 0.002 to 2.0 in. per min. Strain aging during the tensile test appears to explain the ductility mininmum at —77°C. The apparent increase in hydrogen tolerance at lower temperatures is attributed to the low mobility of hyhogen. Experiments were performed in which samples were prestrained in tension at room temperature and tested to failure at —196°C. Results suggest that hydrogetz segregation to preformed crack nuclei can cause subsequent embrittlement even at temperatures where hydrogen mobility is too low to cause embrittlement in a normal tensile test. COLUMBIUM is an example of the class of bcc metals with ductile-brittle transition temperatures sensitive to the presence of interstitial atom contaminants. Hydrogen is one of these embrittling contaminants. The embrittling effect of hydrogen is less potent, perhaps, in columbium than in some of the other bcc refractory metals, but it is still a problem of both theoretical and practical interest. Unlike hydrogen in iron and steels, hydrogen in columbium is exothermically rather than endo-thermically occluded. The embrittlement process in exothermic systems has not been studied as extensively as that in endothermic systems, especially at hydrogen concentrations below the limit of solubility. The purpose of this investigation was to evaluate the embrittlement process in initially pure columbium as a function of hydrogen content, temperature, and strain rate. The Cb-H phase diagram, according to Albrecht et al.,1 is shown in Fig. 1. Columbium reacts exothermically with hydrogen producing a solid solution at concentrations of less than about 250 ppm (parts per million by weight) H at room temperature. At concentrations above the highly temperature-dependent solvus a second phase is formed. Like many similar hydrogen-metal systems,2 his system exhibits a miscibility gap with respect to hydrogen solution. Albrecht found the critical temperature of the miscibility gap to be about 140°C, the critical concentration to be 0.23 atom fraction hydrogen, and the critical pressure to be 0.01 mm Hg. Above 140°C there is a solid solution of increasing lattice constant extending across the phase diagram. Hydrogen concentrations of particular interest in this investigation were those below the limit of solubility in columbium. At hydrogen concentrations above the limit of solubility, columbium will contain the hydrogen-rich second phase and will be brittle under most testing conditions because the hydride generally precipitates as platelets with coincident matrix lattice strains.1&apos;3 At hydrogen concentrations below the limit of solubility, the tensile behavior of columbium is expected to be more sensitive to the interrelationships between hydrogen concentration and mobility and the testing variables such as temperature and strain rate. Literature references to the hydrogen embrittlement of metals, especially ferrous alloys and titanium alloys, are too voluminous to mention. It is only recently, however, that detailed studies of the hydrogen embrittlement of columbium have been undertaken. Wilcox et a1.4 studied the strain rate and temperature dependences of the low-temperature deformation behavior of fine-grained are-melted columbium (1 ppm H) and the effect of hydrogen content (1,9, and 30 ppm H) on the mechanical behavior of columbium at a series of temperatures for a single strain rate. A strain-aging peak was ob-served at about -50°C which was attributed to the presence of hydrogen in the metal. Eustice and carlson5 studied the effect of hydrogen on the ductility of V-Cb alloys at a series of temperatures over the range -196° to 25°C. Pure columbium was embrittled by 20 ppm H which produced a ductility transition at approximately -70°C. Ingram et al.6 studied the effect of oxygen and hydrogen on the tensile properties of columbium and tantalum. A minimum in the notched-to-unnotched tensile ratio of hydrogenated columbium was obtained at about -75°C, but because of the relatively large hydrogen content employed (200 and 390 ppm) the ductility

Jan 1, 1965

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By Frank Tolonen

IRON-ORE beneficiation is becoming of vital importance to the Lake Superior region, since only a few decades will be needed to exhaust the direct shipping ores even if generous allowances are made for discoveries of new orebodies. If the region is to continue as the chief source of ore to the steel industry of the United States, it must concentrate or otherwise beneficiate the enormous tonnages of available iron formations. A beginning along this line has already been made. About one-fifth of the total shipment, even now, is the product of some sort of concentrating process, while another fifth is improved in physical structure by crushing, screening, drying, sintering, or some other similar method. The amount of material amenable to these processes is limited, however; and, in order to be able to utilize the billions of tons of iron formations that cannot be so beneficiated, an intensive study of their nature and concentration possi-bilities is necessary. As long as high-grade ores are available in ample quantities, ore dressing is economically impossible, but as soon, as the supply nears exhaustion it becomes necessary. At first the products of ore dressing must meet as nearly as possible the same specifications as the rich ores in order to be adapted to the reduction processes already established. The future requirements as to quality will depend on the one hand upon the ability of the ore dresser to eliminate undesired constituents and charac-teristics in the material, and on the other upon the adaptation of the reduction processes to the product that can be economically supplied. A better understanding of the blast furnace and other reduction reactions, and improvements in the preparation of raw materials, should enable the Michigan districts to continue to supply ore for a long time to come. The study and testing of the iron formations necessary to bring a utilization of the low-grade ores, though requiring time and effort on the part of all concerned, should not be postponed, especially since the economic situation forces the use of the highest grade ore in preference to the leaner material.

Jan 1, 1933

By Kurt Stock

The grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: Total, Not Leap, Iron, Cadmium, Over. Per Per Cent. Per Cent. Per Cent. Cent. A. High grade.................. 0.07 0.03 0.05 0.10 B. Intermediate................ 0.20 0.03 0.50 0.50 C. Brass special................ 0.75 0.04 0.75 1.20 D. Prime western............... 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages. Smelters engaged in the smelting of custom ores had occasional complaints about the quality of their metal, as some of the consumers, especially brassmakers and some galvanizers, used the rigid standards of the A. S. T. M. as a basis for obtaining redress from zinc smelters whenever some of their work was faulty. Indirectly, much good resulted from such complaints; for while the brassmakers and galvanizers, on the whole, did not know what was wrong, the metallurgists in charge of zinc smelters were induced to abandon their conservatism and study the influence of impurities in spelter from the point of view of the consumer. For some of us, spelter gradually ceased to be considered merely spelter; it

Jan 1, 1925

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.&apos;-&apos; Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence. The combining problem is important in evaluating drilling results at Chuquicamata. Recently a reappraisal has been made of recovery variables and their effect on assays, with the result that a new combining method is offered which fits average drilling conditions and is mathematically reasonable. It is simple in application, fundamentally correct, and an improvement over most combining methods. At Chuquicamata diamond drillholes are used to outline the grade and position of blocks of normal and marginal grade oxide, mixed, and sulphide ore. Most holes penetrate all classes of material (and waste), and it is important for mining programs as well as ore reserves to know almost precisely the soluble and insoluble copper content of mineralized ground. At present three classes of ore are mined and treated differently. For an orderly sequence of mining operations which can provide regular daily tonnages of all three ore types and keep grade at certain levels with minimum variation, ore type and its grade must be predicted. Diamond drilling plus geologic mapping and bench sampling are tools for prediction. And drilling data are largely used to calculate grade of material more than a few meters away from bench faces. The orebody at Chuquicamata" is criss-crossed by millions of barren or mineralized weak to fairly strong slips and fault fissures. Mineralization is diverse and encompasses many quartz and oxide or sulphide-bearing copper veins, as well as seams and disseminated grains. Copper occurs in oxide or sulphide minerals or mixtures of these two mineral types. Rock conditions vary from intensely seri-citized (soft and porous) through clay-altered ground to almost fresh granodiorite. The result is an orebody which offers many obstacles to good and consistent core recovery in diamond drilling. Recovery varies considerably in the several alteration zones, the various types of oxide and sulphide ores, and the position and inclination of the drillhole within the complex fracture pattern. As core recovery drops sludge samples must be used with core samples to calculate grade. Many years of drilling at Chuquicamata indicate that in good grade oxide zones and in the sulphide areas core recovery is good and the ground uniformly mineralized. Moderate loss of core, therefore, does not markedly affect grade calculations based on core assays. An early core-sludge combining method used core assays at face value as indicating grade down to 50 pct core recovery, but below this recovery percentage sludge samples were used and weighted according to the standard Longyear chart. This method apparently did not introduce serious errors, but it abruptly used sludge assays with high weighting factors representing 100 pct return irrespective of actual percentage of sludge recovered. Recent drilling activities have been directed toward outlining the marginal ore areas. The non-uniform mineralization and generally poorer core recovery in such ground indicated that a more exact core-sludge combining method was required to equate wide differences between core and sludge assays and recovery. In fringe ore areas at Chuquicamata core recovery averages about 50 pct, from a minimum of 10 to 15 pct to a maximum of 100 pct. Sludge recovery is likewise variable and averages perhaps 80 pct even though holes are cemented as water return falls off. In a homogeneously mineralized area cut by many slips and faults, with hard and soft ribs, loss of core is loss of ground which has a grade similar to that of core recovered, and core assays approximate true grade. In this case sludge samples need not be used. However, it would be unusual to know beforehand that an area is uniformly mineralized, and in fact this condition is probably uncommon. Generally the distribution of valuable minerals in the ground does not exactly compare with their recoverability in core. Thus, in the usual case, loss of core decreases the

Jan 1, 1956

By W. C. Leslie

The textures of cold-rolled and of annealed iron are compared with those of an iron-0.8 pct copper alloy in which the amount of precipitation after cold rolling was controlled. Previously published pole figures -for cold-rolled and for annealed iron are confirmed. The effects of precipztatiotz after cold rolling are to retain the cold-rolled texture after annealing, to inhibit the formation of the usual allnealing texture, and to produce elongated recrys-tallized ferrite grains. It is suggested that the inhibition of new textures by precipitation after cold rolling is a general phenomenon. A great deal of attention has been paid to the development of texture during the secondary or tertiary recrystallization of ferritic alloys, but very little work seems to have been done on the control of texture during primary recrystallization. If such control were attained, it might be possible to simplify the processing of oriented materials or to change the characteristics of current cold-rolled and an-nealed products. From previous experience, it seemed likely that texture could be controlled by recrystallizing a supersaturated solid solution. Green, Liebmann, and Yoshidal found that the formation of preferred orientation in aluminum (40 deg rotation about <111> relative to the deformed matrix) was inhibited when iron was retained in supersaturated solid solution in the strained aluminum. The authors attributed this inhibition to iron atoms in solid solution. There is, however, an alternative explanation. Green et al, took a highly supersaturated solution of iron in strained aluminum and heated it to an unspecified temperature for recrystallization. It is probable that precipitation occurred prior to and during recrystallization, and it is proposed that the inhibiting agent is this precipitate, rather than the iron atoms in solid solution. It is important to note that precipitation before cold work is ineffective; the effective precipitate is that formed after cold working and either before or during recrystallization. The location and distribution of the precipitate are critical. Precipitation in such a manner has been found to have profound effects upon kinetics of recrystallization and the microstruc-ture of the recrystallized alloys.2-4 It would be surprising, indeed, if this were accomplished with no change in texture. Because of the relative simplicity of the system, and because of previous experience,4-7 it was decided to determine the effect of precipitation on texture in an alloy of iron and copper. Bush and Lindsay5 found an unspecified change in texture in cold-rolled and annealed low-carbon rimmed steel sheets when the copper content exceeded 0.1 pct. MATERIALS In earlier work, the rate of recrystallization of a low-carbon steel was greatly decreased by 0.80 pct copper, and, after the proper treatment, the recrystallized ferrite grains were greatly elongated.4 Accordingly, it was decided to investigate the effect of precipitation on texture at this level of copper content. The iron and the iron-copper alloy were made from high-quality electrolytic iron and OFHC copper, vacuum-melted in MgO crucibles, cast, hot-rolled to 0.2 in., then machined to 0.150 in. The compositions are given in Table I. The plates were heated to 925°C and brine quenched, twice. This produced a ferrite grain size of ASTM 0 in the iron and ASTM 1 in the Fe-Cu alloy. Disk specimens were cut from the heat-treated plates, repeatedly polished and etched, then used to determine (110) and (200) pole figures by reflection. Despite the complication of large grain size, these pole figures strongly indicated a random texture. PROCEDURES The copper content in solid solution in ferrite before cold rolling and recrystallization, and hence, the amount that could precipitate during the recrys-tallization anneal, was controlled at three levels by heat treatment. The specimens as quenched from 925° C were presumed to have all the copper, 0.80 pct, in solid solution. Other samples of the quenched alloy were aged 5 hr at 700°C to retain about 0.5 pct Cu in solid solution.6 A third set of quenched specimens was reheated to 700°C, then slowly cooled in steps, to reduce the amount of copper in solid solution to a very low level. All specimens were cold-rolled 90 pct, from 0.150 to 0.015 in. thick. The rolling was done in one direction only, i.e., the strip was not reversed between passes, with a jig on the table of the mill to keep the short specimens at 90 deg to the rolls. The rolls were 5 in. in diameter and speed was 35 ft. per min. Machine oil was used as a lubricant. In a supersaturated alloy, the maximum effect of the copper precipitate on microstructure and on recrystallization can be developed by a treatment at 500°C, after cold rolling and before recrystallization.&apos;

Jan 1, 1962