Search Documents

By C. Norman Bowers, Blaine B. Wescott

MARKED improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced. is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pump¬ing conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on .the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

By Carl Zapffe

In ten years the manganiferous iron ores of the Cuyuna District have become impor-tant in the iron industry. By Dec. 31, 1923, 4,735,806 tons had been produced. Dur-ing the war, the low-phosphorus black ores were in demand; now the high-phosphorus low,-silica brown ores are favored. It is estimated that the reserves of these ores are ample for some time. A RISE in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for the present economic prominence of this district. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district.

Jan 12, 1924

By G. H. Fancher

Improving economic conditions are reflected in the statistical picture of the petroleum and natural gas industry for 1933. Prices were better, demand was greater and the volume of production increased. The increase in the production of gas has been due mainly to the utilization of outlets to the new prolific gas fields of Potter and Tioga counties; of oil, to the growing demand for Pennsylvania grade lubricants. It should be emphasized that nowhere is volume of production more subject to control due to the extensive use of secondary methods of recovery and regional peculiarities than in Pennsylvania. A summary of developments in production for Pennsylvania in 1933 of necessity is brief. The data listed in Table 1 are all too few in number and not all that is desirable from the standpoint of accuracy. No state agency for the collection of data exists, no reports are compulsory. Nevertheless, because of the hearty cooperation of many individuals and public spirited corporations, it is believed that the data are as reliable as are obtainable at the present time. Furthermore, records of the past too often are lost, were never in existence or are fragmentary, to say the least. Illustrative of the condition is the fact that no thorough study of the oil and gas-producing regions has ever been made. The publications of the Pennsylvania Topographic and Geologic Survey upon the subject are noteworthy and valuable, especially the most recent one.' The Survey has been handicapped in the work by lack of time, personnel and funds in addition to the difficulties mentioned previously. It is obvious, therefore, that Table 1 cannot be completed for Pennsylvania. The data simply are not in existence. Officially there are 328 oil and gas pools or fields known by name and 58 distinct sands or horizons, one or more of which are productive of oil and gas in the various pools, but reliable data for only three general regions could be assembled.

Jan 1, 1934

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus ½ in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in, bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand.

Jan 1, 1950

By A. B. Stevens, C. J. Coberly

The absolute porosity of a rock or sand may be defined as the volume of the interparticle space expressed as a percentage of the total rock volume. The effective porosity as contrasted with the absolute porosity is the volume of the interparticle spaces which intercommunicate with passages of sufficient size to permit the entrance or recovery of gas or oil, also expressed as a percentage of the total rock volume. A knowledge of effective porosity is of prime importance in estimating the ultimate recovery to be expected from oil and gas-bearing formations. The determination of the effective porosity of a rock includes the measurement of two values: (I) the volume of the rock as a whole, and (2) the volume of the grains and sealed pore space. This paper deals with a new apparatus which has been called a "hydrogen porosimeter" for determining the volume of the grains and the sealed pore space. This volume is determined by means of the pressure relations established in the instrument by the introduction of a known quantity of hydrogen. The Hydrogen Porosimeter The apparatus used in this work consists of an upper chamber for measuring the gas, a lower chamber for holding the sample to be tested, a gage for measuring the pressures, a tank of hydrogen, and the necessary connections. (Figs. 1 and 2.) Of the several gases that might be used for this work, hydrogen has been chosen for three reasons: (1) it deviates less from the gas laws than most gases; (2) it readily penetrates the sample; (3) it is absorbed less than most gases by the solids and liquids with which it may come in contact. Method of Operation After placing the sample to be tested in the lower chamber, the apparatus is thoroughly flushed with hydrogen to remove all air from the system, which is then brought to atmospheric pressure Po. The valve connecting the two chambers is next closed and the pressure in the upper chamber is brought up to a pressure PI by admitting gas from the tank.

Jan 1, 1933

By G. E. Erdman

Gouverneur Talc produces a dry mineral filler from the tremolite talc rocks located near Gouverneur, New York. The raw material for this rock powder is a silicate rock and dust is controlled by water sprays whenever it becomes a problem underground. In the milling operation, there are some nine baghouse-type dust collectors which are utilized for the control of dust created in the crushing and grinding process. These collectors have been installed over a period of years since 1947 and are assigned to specific areas where the particle sizing of the dust can be returned to the plant circuit or product involved at the point of collection. It has been found very advantageous to mount most of these collectors on the top of the mill building and packhouses where the return of the dust can be accomplished by a gravity feed. In the years of effort involved in efficient control of dust generated in the plant, many things have been learned in the construction of ducts for control valves. The company has found useful such things as grasshopper legs for interconnecting silos with similar products, the elimination of fiat dust ducts, cleaning cyclones for coarse dust or heavy loadings, refractory linings for cyclones and certain duct areas, and the avoidance of square intersections when diverting or combining ducts. Operating cost records indicate that collectors handling the finest dust have the least expense. Operating costs on high-temperature dusts generally run higher than other types of material collected. Experience further indicates that the multiple cyclone-type collectors can provide a low cost and efficient way of removing hot dusts from process air streams before the introduction of the material into a baghouse. High moisture conditions and cold northern climates have been found to combine and create conditions under which baghouses can not efficiently function as dust collectors. Gouverneur Talc feels that its several dust collection systems have been a considerable maintenance expense but well worth the cost when it came to safeguarding the employees' health and preventing air pollution.

Jan 1, 1974

By A. H. Tousley, C. L. Vickers

The author presents a history of the development of the Port of Long Beach from its beginning in 1905 to the present construction of a new bulk loading facility. In describing this new facility, emphasis is placed on such aspects as rail car and truck handling, gravity yard, rotary car dumping, bottom dumping, car dumping equipment, feeding and conveying, ship-loader-stockpiler, stockpiling and reclaim, dust control, and construction problems. Development of the Port of Long Beach, Calif. (see Fig. I), began in 1905. In that year private Long Beach interests acquired 800 acres of marshland in the Inner Harbor area and initiated a program of channel dredging and land reclamation. Efforts to establish a municipal port began a short time later and culminated in the opening of Pier 1 in 1911. An event of even greater significance to the port future also occurred in 1911. This was the tideland grant enactment by the state legislature that conveyed to the city of Long Beach all of the state's rights in the tidelands located within the city boundaries. The grant stipulated that all revenue produced from the tidelands be used for the development of navigation, commerce, and fisheries. During the next 15 years up to 1926, the port's commercial growth was steady, although relatively slow. During this period, several fundamental steps in the development of a major harbor were accomplished. These included the creation of the Board of Harbor Commissioners in 1917, the dredging of the Inner Harbor and entrance channel to accommodate deep draft vessels, and the correction of a serious silting problem through construction of the Los Angeles River Flood Control Channel. These efforts bore fruit during the ensuing 10 years in the establishment of more than $30,000,000 worth of industrial plants and private marine terminals in the Inner Harbor. Commerce over municipal wharves also increased more rapidly, and it became necessary to start the development of the harbor in a seaward direction. In 1936, oil was discovered in the harbor area, and the first Harbor Dept. well was brought in 2 years later. It soon became evident that the city of Long Beach would receive substantial revenue that, under the terms of the state grant of 1911, must be used in the development of the port. It was further realized that to properly guide and coordinate such development, a long range comprehensive plan was essential. The Board of Harbor Commissions contracted with G. F. Nicholson and J. F. Collins, consulting engineers, for the preparation of such a report that was completed in 1940. The Nicholson-Collins report proposed the development of an East Basin, between the entrance channel and the Los Angeles River, and a West Basin in the area now occupied by the Long Beach Naval Shipyard. Twenty full-size berths were to be provided in the East Basin and more than fifty berths in the West Basin. The report recommended extensive modern terminal facilities for handling waterborne cargo. Attention was given to improvement of the street and highway system to give better vehicular access and to avoid congestion within the port. To a large extent the recommendations of the Nicholson-Collins report were followed in the subsequent development of the East Basin. This development was greatly accelerated by World War 11, with its need for increased oil production and additional shipping facilities. The wartime and immediate postwar construction was largely concentrated on Pier A, with the development of Piers B, C and D following in more recent years. An important factor in the planning of these piers was their dual function as oil drilling sites and cargo piers. The Navy's acquisition of the West Basin area made it necessary to depart from the Nicholson-Collins plan and find other areas for future expansion. At the present time only one Inner Harbor Port-owned area having protected deep water frontage remains undeveloped. This is the property fronting on Channel 2 in the Inner Harbor acquired in December 1957, from Pacific Dock and Terminal Co. The growth of the port has been in a southerly direction since the construction of the Long Beach Naval Shipyard in the West Basin area. Recent extension of Piers F, G and J into the ocean follows typical port construction methods developed during the expansion of the Middle Harbor during the last 20 years.

Jan 1, 1963

By AIME AIME

MATTERS pertaining to mine ventilation were, taken up at the annual meeting Wednesday morning with E. A. Holbrook in the chair. In the absence' of its author, G. E. McElroy, the first paper, entitled "Economic Size. of Metal Mine %Airways," was read by title by the chairman. The second paper, "Intermittent Mine Ventilation," by Oscar A. Glaeser, was 'abstracted by Dan Harrington. It related to metal-mining practice, being inapplicable to coal mining, of course. B. F. Tillson asked how the ,quantity of air was measured and con- trolled in the different splits and Mr. Harrington stated that an anemometer presumably was used and that split- ting was controlled by adjusting the steel doors to the desired position by means of screws. George 'S. Rice asked if the fan were underground, and Mr. Harrington replied that it was. Although he had at, one time recommended that it be placed' on the surface, certain factors led the management to keep it underground, a. location that has several advantages in this particular case.

Jan 1, 1932

By R. W. Carpenter, J. C. Ogle

It is possible, by using pack-rolling instead of conventional rolling, to reduce a number of metals to thicknesses of 2µm or less. Such thinfoils are generally made at room temperature without intermediate annealing. In addition, pack-rolled foils fail by developing pinholes at thicknesses near 2µm instead of developing the shear cracks usually observed in cold-rolled ductile metals. This paper presents the results of a general investigation of the deformation substructure and texture developed in copper and iron pack -rolled from 130 to about 2µm thickness. Electron microscopy showed that in both metals a fine (0.2 to 0.5?µ m) deformation subgrain structure formed during pack-rolling; in neither case was this substructure grossly different from substructures formed during conventional rolling. The deformation texture formed in pack-rolled iron was quite similar to usual bcc textures; however, in the case of copper, the cube texture was stable during pack-rolling and the normal copper deformation texture was unstable. It is shown analytically that the constraining pack induced a large hydrostatic pressure in the foils during pack-rolling. The pinhole failure mechanism is attributed to the presence of the large hydrostatic pressure during pack-rolling; this strongly suppressed the growth of shear cracks. The stability of the cube texture in copper is also probably due to the unusuul stress distribution developed during pack-rolling. EXPERIMENTS at several laboratories have shown that very thin foils of the common structural metals and many of the rare earths can be made by "pack-rolling". 1-3 The technique was originally developed to make specimens for nuclear scattering experiments and foils for X-ray filters. It is also useful for making experimental laminar metallic composite bodies and foils thin enough for direct examination by ultra-high voltage electron microscopy without the need for special thinning techniques. Pack-rolling in the present context means a three-layer pack, with the material to be rolled into foil comprising the center layer. The outer two layers, which constrain the foil during reduction, are ordinarily austenitic stainless steel. Typically, a 130 µm (0.005 in.) metal strip can be reduced to a final thickness of 2 µm or less by this process. This is accomplished at room temperature, without intermediate annealing. It has been observed that foils produced by this process do not exhibit at any stage of their reduction the severe work-hardening found in strip rolled by conventional cold-rolling methods. Neither is the failure characteristic the same."&apos; Conventionally cold-rolled ductile metal strip fails by developing shear cracks on planes whose normals nearly bisect the angle between the rolling direction and normal to the rolling plane; these are planes of maximum shear stress. In pack-rolling this mechanism has not been observed; failure occurs by the formation of pinholes on the foil surface (penetrating the foil). If pack-rolling is continued the hole density increases. These differences in behavior imply the existence of appreciably different substructure in pack-rolled foils compared to substructure in conventionally rolled material, or perhaps that the geometry of pack-rolling has an effect on the foil behavior. This paper describes an investigation of deformation substructure and texture in some specimens of pack-rolled copper and iron, and some considerations of the stress distribution in the foils during rolling that result from the geometry of pack-rolling. EXPERIMENTAL DETAILS Three different materials were used for pack-rolling in the present work: soft copper sheet (99.8 pct Cu, 0.03 pct 0, electrolytic tough pitch) and two types of iron, Ferrovac E* and Armco iron. Each was "Crucible Stccl Co. initially in the form of 130 µm annealed strip with grain size ranges of approximately 10 to 40 µm. The initial texture of the copper (determined as noted below) was the normally observed cube type (001)[100]; there was evidence of a small amount of material in the cube-twin orientation reported by Beck and Hu.4 The initial texture of the Ferrovac E was similar to that reported for recrystallized iron by Kurdjumov and sachs,5 who list the principal orientations as {111}<112>, {001}<110> 15degfrom RD and a weak component {112}(110) 15 deg from RD. The starting texture of the Armco iron was not determined. Pack-Rolling Procedure. A four-high mill was used for all specimens. The work roll and backing roll diameters were 1.625 and 5.25 in., respectively. The peripheral roll speed of the work rolls was about 2.5 in. per sec. All foils were initially reduced from 130 to 100 µm by conventional straight rolling and then inserted into a pack, without any intermediate annealing, for further reduction. The pack consisted of an 0.033 in. (838 µm) thick 3 by 6 in. polished sheet of austenitic stainless steel, folded to make a 3 by 3 in. jacket. After folding, the jacket was given a small reduction to close the fold tightly before insertion of the foil. During pack-rolling a constant change in roll spacing was made every third pass. The roll-spacing change corresponded to a 5 pct reduction in thickness for a new pack. This approached a 10 pct reduction when the pack had decreased to about half its original thickness. At this point the deformed pack was discarded and a new one

Jan 1, 1970

By H. L. Bilhartz, H. F. Dunlap, C. R. Bailey, Ellis Shuler

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent &apos;saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge&apos;s paper.&apos; In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01&apos; the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By C. R. Bailey, H. F. Dunlap, Ellis Shuler, H. L. Bilhartz

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent &apos;saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge&apos;s paper.&apos; In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01&apos; the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By George S. Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro- posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bituminous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,&apos; it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By T. D. Yensen

In the investigation of the magnetic properties of iron-nickel alloys,&apos; it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount, of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular" giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with or without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a pressure of 1 mm. mercury. The ingots, weighing about 2 kg., were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1922

By S. G. Gibbs

A new method for predicting the behavior of sucker-rod pumping systems is presented. The pumping system is described by a flexible mathematical model which is solved by means of partial diflerence equations with the aid of computers. Polished rod and intermediate-depth dynamometer cards can be calculated for various bottom-hole pump conditions. The technique permits simulation of a wide variety of operating conditions, both normal and abnormal. The data generated with the new technique are useful in refining the criteria for design and operation of sucker-rod systms. INTRODUCTION Sucker-rod pumping systems are used in approximately 90 per cent of artificially lifted wells. In view of this wide application, it behooves the industry to have a fundamental understanding of the sucker-rod pumping process. Oddly enough, our understanding has been rather superficial. This is evidenced by the semi-empirical formulas which have been used as the basis for design and operation of sucker-rod installations. Thoueh- we have realized the limitations of our methods for many years, it has not been computationally feasible to use more refined techniques. With the advent and widespread use of digital computers, it is now possible to handle the mathematical problems associated with sucker-rod pumping. This paper summarizes a computer-oriented method which can provide greater insight into the sucker-rod pumping process. It is hoped that this technique, and techniques which may evolve from it, will prove to be the tool needed by industry to obtain the most efficient use of rod pumping equipment. THE MATHEMATICAL MODEL Prediction of sucker-rod system behavior involves the solution of a boundary value problem. Such a problem includes a differential equation and a set of boundary conditions. For the sucker-rod problem, the wave equation is used, together with boundary conditions which describe the initial stress and velocity of the sucker rods, the motion of the polished rod and the operation of the down-hole pump. Of these items, the wave equation, the polished rod motion condition and the down-hole pump conditions are of primary importance. Discussion of the mathematical model centers about these factors. ROD STRING SIMULATION WITH THE WAVE EQUATION The one-dimensional wave equation with viscous damp- is used in the sucker-rod boundary value problem to simulate the behavior of the rod string. This equation describes the longitudinal vibrations in a long slender rod and, hence, is ideal for the sucker-rod application. Its use incorporates into the mathematical model the phenomenon of force wave reflection, which is an important characteristic of real systems. The viscous damping effect postulated in Eq. 1 yields good solutions, even though nonviscous effects such as coulcomb friction and hysteresis loss in the rod material are present. Fortunately, the nonviscous effects are relatively small, so the viscous damping approximation used in the wave equation is adequate. The coefficient v is a dimensionless damping factor which is found in field measurements to vary over fairly narrow limits. For mathematical convenience the gravity term is omitted in Eq. 1. The effect of gravity on rod load and stretch can be treated separately, as will be noted later. Since Eq. 1 is linear, the legitimacy of this procedure is easy to demonstrate. POLlSHED ROD MOTION SIMULATION The motion of the polished rod is determined by the geometry of the surface pumping unit and the torque-speed characteristics of its prime mover. By determining the motion of the polished rod, we formulate an important boundary condition. From trigonometrical considerations it can be shown that the position of the polished rod vs crank angle 0 is given by (see Fig. 1) These equations are obtained from the general solution of the "four-bar" linkage problem and can be used to describe the kinematics of any modern beam pumping unit.&apos; If prime mover speed variations are disregarded, the angular velocity of the crank is constant, and Eq. 2 can be used to predict the position of the polished rod vs time. However, the constant-speed condition leading to constant crank angular velocity is only approached in practice: hence, it is better to make provisions for prime mover speed variations in the mathematical model. The speed at which the prime mover runs is determined by its torque-speed characteristics and the torque imposed upon it. The torque that the prime mover "feels" is the net torque arising from the polished rod load and the opposing torque from the counterbalance effect. The

By Clarence Hicks

THE labor policy, of the Standard Oil Co. (New Jersey) is founded. first of all on paying at least the prevailing scale of wages in the community; on, the eight-hour day, with time and one-half for overtime; one day&apos;s rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year&apos;s service; cooperation with employee in promoting thrift and better social and housing conditions; and assurance for a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company&apos;s policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co., is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this, principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees&apos; interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer.

Jan 3, 1920

By Herbert Wilson

THIS topic was discussed at the meeting in St. Louis in September, 1917, and at the meeting in New York in February last, but in the interval the war has accentuated in measurable degree the necessity for considering human relationship, not only as between nations, or in the treatment of our returning soldiers, but with respect to the relations between labor and capital in industry. It is my firm conviction that no other subject will have so large a place in industrial and political life during the next decade as this. Heretofore, the employer has been so engrossed with the financial, mechanical, and technical aspects of his business that he, has been willing to muddle through &apos;his relations with labor as best lie might and, on the other hand, the laborer has been so engrossed in his endeavors to secure a livelihood under whatever living and working conditions might be offered him that he has given little thought to his relations to his employer, until some misunderstanding has ended in disagreement and strike. No thinking man doubts that were the machinery available for friendly, personal, face-to-face consideration of the problems confronting employer and employee, there would he fewer disagreements, fewer strikes, and a better and more settled industrial situation. The necessity for some such medium for exchange of views has resulted in the organization of labor and, in some measure, of capital. Each party, engrossed only in defending its own viewpoint, has generally tried to gain its point by might rather than by right. Gradually, however, the representatives of both elements are beginning to appreciate that when the machinery for bringing them together in friendly communion is available their differences frequently settle themselves. There remain yet vast numbers of employers and of employees who are not organized and to whom the opportunity of friendly discussion of differences is not available; for these the machinery should he provided.

Jan 1, 1919

By Carl E. Swartz

Although a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. Characteristics and Requirements of Solders in General General Physical Properties.—When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.—The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

By Hugh S. Spence

The use of natural feldspathic rocks, as opposed to straight feldspar, for ceramic purposes is not new. "Cornwall stone," a semi-kaolinized granite containing fluorite, has long been used by the English pottery trade instead of feldspar, and "Carolina stone," a similar rock, is now being offered to the American trade. A recent report of the U. S. Bureau of Mines states that trachyte, a glassy volcanic rock, is being used in California instead of feldspar in ceramic bodies. In Germany, phonolite and basalt have been investigated, and possibly also used, as ceramic raw materials, and extensive research has been conducted in Russia in recent years looking to the utilization of the immense bodies of nepheline syenite of the Kola Peninsula, which is the host rock of the apatite deposits now being exploited on a large scale in the Murmansk region; the nepheline is recovered as a by-product of the concentration of the apatite. Long used principally as a raw material for the pottery and allied industries, where, in bodies, glazes, enamels, etc., it serves as a fluxing ingredient and forms, on firing, a glassy bond with the more refractory clay, flint and coloring particles, feldspar has been finding ever increasing employment in glass. In 1936, over half of the nearly quarter of a million tons of feldspar sold in the United States went to the glass trade. Its usefulness for this purpose is due to the resistance to thermal shock which it imparts to glass products, particularly bottles, containers and tableware, because of its alumina content, which averages from 16 to 20 per cent. Active search has been wade on the American continent during the past few years for other minerals of feldspathoid type, with comparable or higher alumina content, that, may be suitable for glass and other ceramic purposes. One of the most important results of this work has been the delimiting in central Ontario of large bodies of nepheline syenite of excellent, ceramic grade.

Jan 1, 1942

By Hugh S. Spence

The use of natural feldspathic rocks, as opposed to straight feldspar, for ceramic purposes is not new. "Cornwall stone," a semi-kaolinized granite containing fluorite, has long been used by the English pottery trade instead of feldspar, and "Carolina stone," a similar rock, is now being offered to the American trade. A recent report of the U. S. Bureau of Mines states that trachyte, a glassy volcanic rock, is being used in California instead of feldspar in ceramic bodies. In Germany, phonolite and basalt have been investigated, and possibly also used, as ceramic raw materials, and extensive research has been conducted in Russia in recent years looking to the utilization of the immense bodies of nepheline syenite of the Kola Peninsula, which is the host rock of the apatite deposits now being exploited on a large scale in the Murmansk region; the nepheline is recovered as a by-product of the concentration of the apatite. Long used principally as a raw material for the pottery and allied industries, where, in bodies, glazes, enamels, etc., it serves as a fluxing ingredient and forms, on firing, a glassy bond with the more refractory clay, flint and coloring particles, feldspar has been finding ever increasing employment in glass. In 1936, over half of the nearly quarter of a million tons of feldspar sold in the United States went to the glass trade. Its usefulness for this purpose is due to the resistance to thermal shock which it imparts to glass products, particularly bottles, containers and tableware, because of its alumina content, which averages from 16 to 20 per cent. Active search has been wade on the American continent during the past few years for other minerals of feldspathoid type, with comparable or higher alumina content, that, may be suitable for glass and other ceramic purposes. One of the most important results of this work has been the delimiting in central Ontario of large bodies of nepheline syenite of excellent, ceramic grade.

Jan 1, 1942