Search Documents

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Gilmar Zacca Batista

The present work is a part of a comprehensive program that aims to evaluate the girth welding procedures for heavy wall API 5L X65 pipes produced for sour service applications. This article describes the results of toughness, strength and sour resistance of girth welds produced with different welding consumables. The methodology applied included girth welds production with GTAW process for root pass using ER70S-6 consumable and FCAW process for filling passes using E71T- 1CJ and E91T1-GM-H4 consumables. Mechanical tests of Charpy, CTOD, tensile, hardness and stress corrosion cracking were also performed. The E71T-1CJ resulted in a girth weld with tensile and yield strength around 7% lower than the pipe. However, according to the papers analyzed at this study, a value up to 10% of undermatching could be acceptable. The CTOD and Charpy tests showed good toughness and weld metal embrittlement was not observed. The hardness and the stress corrosion cracking tests demonstrated that the consumable ER70S-6 is suitable for sour service. All properties evaluated met the requirements specified by the onshore pipeline standards, showing that the consumables ER70S-6, E71T-1CJ and E91T1-GM-H4 are suitable for the welding of heavy wall X65 pipe with sour service and toughness requirements. If an overmatching is required, the E91T1-GMH4 shall be used to assure a strength overmatching and prevent plastic strain concentration at the weld metal. The results provided by this paper can be used for consumable selection and for welding procedure qualification of pipelines construction when heavy wall API 5L X65 are used for sour gas transportation.

Aug 16, 2017

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Douglas Glenn Stalheim

The uniformity of the final cross sectional microstructure and subsequent final mechanical properties and shape of structural steels is dependent on the type or types of recrystallization behaviors that are created. There are three main recrystallization behaviors that are the foundation of the metallurgy created during production. Alloy design and subsequent processing design strategy drive how much of each recrystallization behavior is created through the cross section of the product. Carbon manganese steels create only one basic behavior while the addition of microalloys, in particular niobium, can add two additional behaviors. The behaviors are intertwined with each other and build upon each other. The three behaviors are Type I, static recrystallization, Type II, no-recrystallization, and Type III, metadynamic/dynamic recrystallization. How much of each behavior is generated through the cross section through the production influences the final transformed microstructure and corresponding mechanical properties and shape performance. This paper will discuss the three behaviors, how they are generated, how to identify which behavior is occurring through modeling or actual mill data. Actual examples from production will be discussed.

Aug 16, 2017

By Eduardo Dominguez Trindade

Lubricant oils are subjected to reciprocating movement in the piston ring/cylinder tribocouple of automotive engines. In this kind of movement, the relative speed oscillates between zero and a maximum, and therefore the lubrication regime goes from boundary to hydrodynamic. Tribotests are widely used in laboratories to hint at the friction developed in these systems. In the present work, a SRV tribometer was used to evaluate the friction behaviour of lubricant oils under reciprocating movement up to 60 Hz. A high acquisition rate allowed the analysis of data inside each reciprocating cycle. Both a pure base oil and a fully formulated lubricant were used. Changes in the contact pressure, viscosity and speed were seen to influence friction, which was correlated to the relative thickness predicted by Hamrock-Dowson equation. While some observed characteristics were typical consequences of the Stribeck curve, other effects were also observed, such as the occurrence of seizure at high reciprocating frequency. A lower boundary coefficient of friction due to additive package in the formulated oil was also observed. The results allow a better understanding of friction in reciprocating cycles and can be used to evaluate the performance of oils and surfaces in laboratory prior to engine testing.

Jul 31, 2018

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By Valeria Romina Stricker

Acerbrag es una empresa Argentina siderúrgica de 50 años de trayectoria, desde el año 2007 pertenece al grupo Votorantim de origen Brasilero. Se dedica a la elaboración de aceros largos para la construcción. La planta industrial cuenta con un proceso de acería integrado, horno eléctrico, horno cuchara y máquina de colada continua. La materia prima es 100% chatarra, característica que la diferencia del resto de las acerías del país. Debido a esto el enfoque principal de este proyecto es reducir el costo de fabricación mediante un “empobrecimiento” de la carga metálica a partir de la flexibilización de los límites de especificación. Esto implica un mayor control del desempeño de los procesos a fin de detectar posibles desvíos, para ello fue necesario implementar la utilización de herramientas estadísticas y gráficas para su monitoreo. La modificación en el mix de fabricación no muestra una alteración significativa en la composición química y propiedades mecánicas de los productos terminados, situación favorable para la continuidad del proyecto. Se observa además, de la reducción de costo esperada, una ventaja en la operación del patio de chatarra y el proceso de acería y en la utilización de chatarras con altos niveles de residuales tales como Cr – Ni.

Aug 16, 2017

By Andrelio Marcos Ribeiro, Lucio Ribeiro Camisao, Antonio Carlos Ataíde, Alan de Sousa Pereira, Renato Siqueira Campos

The annealing and pickling line n. 1, responsible for the production of stainless steel 3xx, 4xx and 430a in thicknesses from 4 to 0.4 mm, has two vertical strip accumulators. These are intended not to let the material exceed the determined time in the furnace and in the pickling, and consequently do not cause defects like burning and excessive pickling. Strip accumulator n. 1 avoids the line from stopping during welding execution of the coils in the welding machine. In sequence, the strip accumulator n. 2 avoids the line from stopping at the end cutting of the tips, and in the coils removal from the pickling. The strip accumulators have a roller table that during the strip accumulation moves vertically downwards while its counterweight moves vertically upwards, and do the inverse movement when the material is released. On December 12th 2018, the failure occurred in the strip accumulator n. 1, where it was verified that the shaft of one of the pulleys had been fractured by high-cycle mechanical fatigue, which was characterized by alternating bending. With the fracture of the shaft, occurred the unevenness of the counterweight that damaged the guides. Failure analysis of this occurrence was based on the PDCA methodology, when was verified a weld between the shaft and the pulley. The analysis of the microstructure transformation in the molten zone, in the heat affected zone and in the base metal was carried out in an optical microscope, and no abnormality was observed. It was also carried out the end test by penetrating liquid, finding an inadequate weld in its geometry, as well as longitudinal trunks along the center of the weld bead. However, after a huge investigation of the causes, it was found that the failure was triggered by an inadequate design of the pulley shaft. It was also verified that the shaft had an open measure, inadequate for the operational context. After the analysis, action plans were drawn up based on the FMEA methodology to inhibit the failure recurrence.

Oct 7, 2019

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019