Search Documents

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Jinhui Li

Silver is a very important metal used in a wide range of applications. It is necessary to recovery of Ag from electronic wastes for increasing of Ag price and circumstance protection. For separating and recycling Ag from Ag-Cu composite materials, thermodynamic data of reaction is calculated and some experiments have been proceeded with Ag-Cu composite material scraps, time, temperature, nitric-sulfuric mixed acid volume ratio and the volume ration of mixed acid vs. water have been discussed. The results show that the optimization conditions is that nitric-sulfuric mixed acid volume ratio 5:95, volume ratio of mixed acid vs. water 10:1, temperature 55?, time 25min. In the conditions, Ag can be selectively leached from Cu-based composite material, Cu base is not eroded nearly.

Jan 1, 2009

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

SEVERAL serious accidents, which had occurred owing to the platman leaving the plat without first withdrawing the "chairs" from the shaft, set the writer scheming to devise a mechanically operated system which would obviate such accidents and be "fool-proof". It was obvious at the outset that some means of indicating to the engine-driver by the movement of the "chairs" themselves, whether they were "in" or "out" of the shaft, was necessary.An arrangement of signalling similar to railway semaphores was considered, but was rejected owing to the difficulties accruing from the large number of communicating wires which would be required down the shaft-viz., 2 for each level. After several experiments, a comparatively simple and efficient electrical system was devised, and which is covered by Commonwealth Patent TO. 10,402.One of the chief features of the apparatus is its simplicity, and its strongest point is the fact that both the engine-driver and platman receive visual indication of the position of the "chairs." The arrangement consists of a miniature coloured glow lamp, one for each level of each shaft compartment, arranged and placed beside the numbers and arrows corresponding to the various levels, on the winding engine indicators. Also a large indicating glow lamp is installed at each compartment in the various levels, in proximity to the levers for operating the "chairs." Upon operating the various levers for the "chairs," an electrical current...

Jan 1, 1909

By M. Iberico

A partir de los años 70 se incrementó el proceso de exploración y desarrollo de los yacimientos mineros submarinos. En este sentido, el presente trabajo describe el origen de los depósitos a partir de los descubrimientos de módulos manganíferos en el océano pacífico que hicieron Thompson y Murray. Posteriormente Buchanam demuestra la existencia de módulos ferro-manganíferos en aguas poco profundas ( 200 m. ), de composición diferente de las provenientes de aguas profundas. De otro lado, el trabajo señala también la división de los minerales marinos en tres categorías: las sales disueltas y en organismos, los sedimentos y depósitos en el suelo profundo submarino y los depósitos consolidados e inconsolidados de la plataforma continental. Por último, se describe los procesos de beneficio y las ventajas de la explotación de los recursos submarinos en el futuro de la minería submarina.

Nov 20, 1972

By J. D. Jorgenson

?? U.S. domestic production peaked at 120 Mt during years of the Korean Conflict120 Conflict ?? Pellet production increased, as highPellet high-grade ores decreasedores decreased ?? Until 1982 recession, most U.S. iron ore mines owned by steel companiesmines companies ?? Large Canadian iron ore mines brought into production after 1950into 1950

May 1, 2011

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By D. Boldini, R. Lackner, H. A. Mang

ABSTRACT: In this paper, the strong interaction between the hardening shotcrete lining and the surrounding ground in NATM tunneling is investigated by means of axisymmetric analyses, accounting for the three-dimensional nature of the excavation process. The effect of the hydration of shotcrete on strength, stiffness, chemical shrinkage as well as microcracking and creep are accounted for. For the description of the mechanical behavior of the ground, a multi-surface plasticity model is employed. The performed analyses of the excavation process provide insight into the influence of each phenomenon accounted for in the material model for shotcrete on the response of the ground-shotcrete compound structure. ZUSAMMENFASSUNG: In diesem Beitrag soll die Interaktion zwischen dem erhärtenden Spritzbeton und dem Boden auf der Basis axisymmetrischer Berechnungen untersucht werden. Derartige Berechnungen ermöglichen die Berücksichtigung des drei-dimensionalen Charakters des Vortriebprozesses. Die Auswirkung der Hydratation auf die Entwicklung der Festigkeit, Steifigkeit und der chemischen Schwindverzerrungen, sowie das Reißen und das Kriechen des Spritzbetons wurde berücksichtigt. Das mechanische Verhalten des Bodens wurde mittels eines Mehrflächenplastizitätsmodells simuliert. Die durchgeführten Berechnungen des Vortriebprozesses geben Einblicke in die Auswirkungen der Spritzbetoneigenschaften auf das Tragverhalten des Boden-Spritzbeton-Komposits. RÉSUMÉ: La stricte interaction entre le soutènement en béton projeté durcissant et le terrain dans un tunnel creusé avec la NATM est étudiée par des analyses axisymétriques, compte tenu de la nature tridimensionnelle des processus de creusement. Les effets de l’hydratation du béton sur la résistance, la rigidité et la contraction chimique, ainsi que sur la micro-fissuration et le fluage, sont mis en compte. Pour la description du comportement mécanique du terrain on emploie un modèle de plasticité multi-surface. Les analyses conduites mettent en évidence l’influence de chaque phénomène considéré dans le modèle constitutif du béton projeté sur la réponse de la structure composite terrain-béton projeté.

Jan 1, 2003

By Keith L. Harris

Recent data indicate a marginal decline in overall growth in world economic output from 3.1% in 1985 to 2.9% in 1986 (table 1),2, 3 Many nations experienced slower economic growth because of the huge trade imbalances existing between the United [ ] States and Japan and the Federal Republic of Germany, the U.S. budget deficit, and the growing Third World debt. Some developing nations, however, experienced booming growth. Declining prices for energy and nonenergy commodities and the fall of the dollar against the currencies of major industrial countries benefited several developing countries--energy importers and exporters of manufactured goods with currencies tied to the U.S. dollar, which were able to expand markets in the industrialized nations. The drop in commodity prices increased demand in industrial countries and depressed it in developing countries. Lower demand in the developing countries contributed to a decline in the real net exports from industrial countries. As a result, output growth in industrial countries declined from 3.0% in 1985 to 2.4% in 1986, despite growing internal demand, Average output growth of developing countries increased from 3.296 to 3.596 during the same period, however, primarily because of the low prices of their products and the strength of demand in industrial countries for those products. Developed country output growth was extremely uneven, however. For example, the economic output of nonfuel exporters grew 5.4% in 1986, while that of fuel exporters dropped 0.7%.

Jan 1, 1987

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By C. Hosten, K. V. S. Sastry, D. J. Kawulok-Englund

Introduction Since the last decade the iron ore processing industry has undergone drastic changes from supplying screened and natural ores to manufacturing tailored concentrates and pellets. Increased need for the beneficiation of lower grade iron ore deposits and the increased demand for higher grade concentrates necessitate finer grinding of iron ores before concentration. The normal filtration stations used in the past are experiencing difficulties in dewatering the finely ground concentrates to moisture levels acceptable for balling. In addition to finer grinding, applications of complex beneficiation techniques has decreased the filterability of the concentrates and create problems in filtration of iron ore concentrates. An overview of the filtration literature indicates there are few research reports on the dewatering of iron ore concentrate slurries. There exists a need to understand the principles and mechanisms involved in the filtration of iron ore concentrate slurries with a goal of developing more efficient filtration techniques. This paper presents the results from the first phase of our research program that included the development of a reproducible benchscale filtration technique and the investigation of the filtration behavior of eight iron ore concentrates.

Jan 10, 1983

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996