Search Documents

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By S. L. Windes

This report presents a tabulation of the physical and petrographic properties of Over 100 rock types from operating mines or mineral-investigation projects. The physical properties include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength, (modulus of, rupture) Impact toughness Abrasive hardness Scleroscope hardness Modulus of elasticity (Young's modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1949

By M. Weatherspoon, S. Gebo, K. Prisbrey

Our objective was to develop a transfer function model of phosphate heap leaching for design, optimization and control. The procedure included analysis of time-lapse photography of a laboratory heap. Our experimental results confirm the predicted system transfer function kinetics. Our conclusion was that the transfer function and z transform that we have developed will allow us to control flow rate and pH online.

Jan 1, 2001

By Kenneth L. Cook

From March 1944 to July 1945 the Division of Geophysical Exploration of the Federal Bureau of Mines made magnetometer surveys of some of the principal iron ore deposits of the Iron Springs district, Iron County, Utah. The district comprises a belt about 23 miles long and 3 miles wide. Most of the large ore bodies are found as pods of replacement ore within a favorable limestone bed lying at the margins of three separate igneous intrusions in the district The magnetic surveys were confined chiefly to this geologically favorable zone at the margins. The iron ore is a mixture of magnetite and hematite. The magnetite content of the ore ranges from 14 to 58 percent. Magnetic anomalies of 1,250 gammas or more were usually found over the near-surface ore bodies. About 62,000 magnetometer stations were taken over a total traverse distance of about 300 miles. Outcropping ore bodies were surveyed to determine, insofar as was possible from the magnetic data, their probable length, width, depth, extent, strike, dip, and tonnage. Geologically favorable areas where no ore is exposed were explored in an endeavor to find new ore bodies. Favorable locations were determined for exploratory diamond drilling, both in areas of exposed ore bodies and in areas of newly discovered magnetic anomalies. Forty-five separate magnetic anomalies that indicate the possible existence of ore bodies were observed. Of these, 13 anomalies are caused by outcropping ore bodies of proved commercial size. Five are caused by non-outcropping ore bodies of proved commercial size which were discovered, in whole or in part, as a result of the geophysical surveys. Of the remaining anomalies, which lie in virtually un-tested areas where few or no ore bodies are exposed, six probably are caused by large, unexposed replacement ore bodies, nine are possibly caused by large, unexposed replacement ore bodies, and six are probably caused by unexposed magnetite veins of some small commercial importance,

Jan 1, 1949

By E. H. Burroughs

This bulletin is the fifth in the series of petroleum bibliographies publis:\:l.ed by the Bure.au of Mines, Bulletins 149, 165, 180, and 189 being compilations for the years 1915, 1916, 1917, and 1918, respectively. In this bulletin the same general plan has been followed in arranging the references, but a few changes and additions have been made in the classification.

Jan 1, 1923

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020

By J. N. Van der Merwe, D. P. Roberts

The two components of pillar design formula being used in South Africa are pillar strength and pillar load. While considerable effort has been directed to the determination of pillar strength, the other half of the safety factor equation, the load, has not received the same amount of attention. The load acting on pillars has always been calculated using the Tributary Area Theory (TAT). This paper summarises the recent studies on coal pillar loading using various numerical models. It concludes that although there are meaningful differences under certain circumstances, there is still a compelling argument to use the TAT in coal pillar design. Les deux parties composantes de la formule de conception de pilier généralement utilisée en Afrique du Sud sont la résistance de pilier et la charge de pilier. Tandis que des efforts considérables on été dirigés vers la détermination de la résistance de pilier, l’autre moitié du facteur de sécurité n’a pas reçu la même attention. La charge agissant sur les piliers a toujours été calculée avec la Théorie d’Aire Tributaire (TAT). L’étude présente résume les études récentes sur la charge de pilier de charbon utilisant des modèles numériques variés. La conclusion est que bien qu’il y ait des différences significatives selon les circonstances, il y a toujours un argument puissant pour utiliser le TAT dans la conception de pilier de charbon. Die in Südafrika für die Auslegung von Pfeilern verwendeten zwei Formelkomponenten sind Pfeilerstärke und Pfeilerbelastung. Während beträchtlicher Aufwand zur Bestimmung der Pfeilerstärke gemacht wurde, wurde der anderen Hälfte der Sicherheitsfaktorsgleichung nicht die gleiche Aufmerksamkeit gewidmet. Die auf die Pfeiler wirkende Last wurde immer unter Verwendung der Tributary Area Theory (TAT) berechnet. Diese Arbeit fast neuere Studien betreffend der Belastung von Kohlepfeilern unter Verwendung verschiedener numerischer Modelle zusammen. Die Schlussfolderung ist, daß obwohl unter bestimmten Vorraussetzungen bedeutende Unterschiede existieren, nach wie vor ein bezwingendes Argument besteht TAT in der Kohlepfeilerauslegung zu verwenden.

Jan 1, 2003

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface metal and nonmetal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. Portions of the handbook that should prove most useful to the inspectors include a survey check list, rules for determining if sampling is required, list of most frequently encountered contaminants, list of candidate contaminants and their sampling conditions, interpretation of results, and a procedure for a health and safety inspection.

Jan 1, 2011

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By James R. Evans

Orange County, adjacent to the populous and industrialized Los Angeles area, is the fastest growing county in California and is second only to Los Angeles County in total population (figure 1). In addition to an equable climate and a burgeoning economy, there is room in Orange County for growth and expansion. Growth over the past decade has resulted in rapid development of industrial tracts, housing areas, and shopping and commercial centers, mostly in former agricultural areas. The value of new building in 1972 was a record amount-over I billion dollars (figure 2). Problems relating to the proper direction of growth are the concern of both government and the private sector. The intelligent and efficient use of areas to be developed requires planning for the conservation and protection of the County's natural beauty and for the orderly development of natural resources. The availability of sand and gravel, which is used in many phases of construction, will be a major controlling factor in the future of the County.

Jan 1, 1974

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By W. van der Merwe

ABSTRACT With the gold industry processing more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more critical. This paper compares the two commonly employed ‘free’ cyanide online analysis methods (amperometric and potentiometric endpoint silver nitrate titration) with the rhodanine endpoint silver nitrate titration and ion selective electrode methods common at site laboratories. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared using these measurement techniques.

Jan 1, 2013

By E. LaRocque

"Long term contracts requiring delivery of 6,000,000 pounds of U308 per year to its customers have made it necessary for Denison Mines to expand its milling capacity from 7,100 tons per day to 15,000 tons per day.Previous papers (1) and (2) described the old leaching and product recovery practice. The flowsheet briefly includes a crushing and grinding circuit, sulphuric acid leaching in a Pachuca plant, liquid-solid separation with wash thickeners and two-stage drum filtration, concentration and purification by moving bed ion exchange followed by two-stage precipitation to produce an ammonia yellowcake.No. 1 Shaft ore, about 4,000 tons per day, will be processed through the truck dump into the old crushing and grinding plant and through the old leaching plant. Ore from Stanrock (No. 3 shaft) will be hauled by truck and also processed through the truck dump as No. 1 shaft ore. Beginning in 1982, ore production from Stanrock will gradually increase until 1985 when some 3,000 tons per day will be milled from the source.A new 8,000 ton per day circuit was designed and constructed to increase the milling capacity to 15,000 tons per day. The new circuit is separate from the old one except that it coins together for the precipitation and tailings neutralization sections of the plant. The feed to the new plant will be from No. 2 shaft.The flowsheet is much the same as the old plant with the exception of the grinding circuit and the ion exchange plant. A semi-autogenous grinding (SAG) plant, unique in the Elliot Lake area, has been installed rather than the conventional crushing and grinding plant; the ion exchange plant is the stationery bed type.This paper describes the major equipment installed for the expanded grinding and hydrometallurgical plant."

Jan 1, 1982

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By Milford L. Skow

MICA is a group name for a number of complex hydrous aluminum silicate minerals that have a sheet or platy structure and extremely variable and complex compositions containing various metallic ions, particularly those from the alkali group. Muscovite and phlogopite, the two varieties of significant commercial value, are the principal consideration of this report; muscovite has major importance industrially. The mica crystal, because of its laminated structure, can be split easily and accurately into thin films that are transparent, flexible, elastic, tough, and waterproof and have outstanding dielectric and insulating characteristics. This combination of properties is not duplicated in any other known substance. The world production of mica can be divided into two main classifications: (1) Sheet mica and (2) scrap mica (including flake mica). In general, separate divisions of the industry produce these two classes of mica, which differ widely in their uses and in the forms in which they are marketed. A glossary of mica terminology is given in appendix A.

Jan 1, 1962

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010