Search Documents

By W. W. Staley

This paper discusses the design of small head frames that will fill the needs of prospectors and small operators whose operations are conducted through shafts. The head frames considered were designed to handle relatively small tonnages. It was assumed that the shafts in which buckets are used would not exceed 300 feet in depth and that not over 60 tons of rock would be hoisted, in, 14 hours. In the design of the larger head frames, a hoisting capacity of about 250 tons per 6 hours from a depth of 300 to 500 feet was assumed. Under these conditions, hoisting speed, rate of acceleration, and weight of rope have a negligible effect on the head frame design and, therefore, have been ignored in the following, discussion. Because timber is relatively cheap and easily obtained in most mining areas, the discussion has been confined to timber construction.

Jan 1, 1937

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By Michael Lane

With the success of their existing casino operation on the Ohio River in Lawrenceburg, Indiana, the Indiana Gaming Co., LP planned a major expansion of the current facilities. This expansion includes a second 1400+/- car parking garage, a new surface parking lot, elevated walkways, and a new floating casino that will double their present square footage and consolidate all of the gaming activity to one floor. In March of 2006 Richard Goettle, Inc. was awarded the general contract to construct a 260? x 520? boat slip for the new Argosy VII floating casino. An Open Cell® bulkhead system was specified as the means for constructing the new slip. Our contract included the purchase and installation of 300,000 square feet of PS27.5 sheet pile, excavation of 230,000 cubic yards of soil, and a 3300 square foot Mechanically Stabilized Earth wall.

Jan 1, 2008

By Lori Kormos, Jhonny Carrión De la Cruz, Dominic Fragomeni, Elizabeth Whiteman, Jorge Oliveira

"Process diagnosis, flowsheet design and optimisation are most effectively and efficiently achieved through the use of metallurgical testwork combined with more modern quantitative mineralogical techniques. Integration of the mineralogical data in testwork programs provides a resolution that cannot be obtained from assays alone and can direct the flow of work to result in optimized conditions more quickly than would otherwise be possible. At Xstrata Process Support (XPS), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro Analyser) information can be employed to diagnose specific issues in a plant or lab scale test and are routinely combined with other metallurgical data sets to benchmark performance, design and optimise flowsheets. Representative sampling protocols for ore bodies or test products, the use of geometallurgical unit classification and high confidence metallurgical test programs are key components of the strategy. Two case studies from Xstrata Zinc’s Antamina Mine and Concentrator in Perú, and Xstrata Nickel’s Nickel Rim South Mine in Sudbury are described to show how the use of quantitative mineralogy were used to diagnose a plant issue and how the data can be integrated into metallurgical programs to assist mineral processing engineers to design and optimise flowsheets.INTRODUCTIONOver the past decade, there has been a shift away from metallurgical testing that employs only chemical assays to quantify performance; the use of empirical observation in order to optimise a flowsheet; and the extraction of bulk samples for testing or piloting. The integration of geological information into the planning and execution of testwork programs including the use of quantitative mineralogy has improved the overall quality and predictability of metallurgical programs. At the same time, improvements to metallurgical testwork protocols such as rigorous statistical assessment of results, the use of factorially designed experimental strategies (DOE), and replicate flotation with appropriate quality controls, has improved the confidence level in these results.Process diagnosis, which utilizes quantitative mineralogy, can clearly define the root cause of the metallurgical issue. Whether used on its own to diagnose an issue or in combination with other metallurgical testwork, the use of mineralogical data has become the standard in the mining industry."

Jan 1, 2010

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By Peter Grundy

La eficiencia de los recursos en los procesos transparentes de gestión de las empresas permite aumentar el valor de los accionistas. En ese sentido, el presente texto señala el uso de la RCM como estrategia en el funcionamiento de un equipo que se centra en la confiabilidad. RCM es un proceso lógico que involucra aspectos técnicos y de negocio, capaz de producir resultados a muy corto plazo. Este proceso concluye con una recopilación de documentos fiables y totalmente óptimos para el desarrollo de las funciones de mantenimiento. Su uso correcto en la evaluación de los requisitos de mantenimiento de los equipos existentes, genera un mantenimiento menos costoso, confiable y eficaz. Asimismo se disminuye los costos de mantenimiento y se relaciona los aspectos ambientales y de seguridad.

Jul 17, 2000

By AIME AIME

THE Iron and Steel and Institute of Metals Divisions will meet jointly at the Statler Hotel, Detroit, Oct. 4 and 5, during the Metal Congress, Oct. 2-6. The Wire Association, the American Welding Society and the American Society for Steel Treating, together with the two Divisions of the Institute, constitute the Congress this year, and each body offers an interesting technical program. The National Metal Exposition will, as usual, be held concurrently. Visiting metallurgists will find themselves engaged in a bit of research not listed in the program-a time study of how best to exploit in a few days both the Congress and all that the place of meeting has to offer. For Detroit, the beautiful "City of the Straits," is third in rank industrially in the United States, and its great manufacturing plants offer much of metallurgical interest. This is especially true of the automobile plants which will be open to members of the various societies during the week of the Congress.

Jan 1, 1933

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By L. B. Davidson

The petroleum literature contains many reports on the relative permeability properties of porous media. However, only recently have studies of relative permeability at elevated temperatures been made.1 -5 Each of these studies presents relative permeability data on water-oil systems in linear sandpacks or sandstone cores under isothermal conditions. The results of these investigations are dissimilar. Edmondsonl found that in Berea sandstone a temperature-dependent effect was present, while Shilobod,2 using the same material, found no temperature dependence after normalizing for initial water saturation. Workers at Texas A&M U.3-5 found that the ratio kw/ko was temperature dependent in an unconsolidated system. The differences in results of these studies are probably a consequence of differences in the material employed, in the experimental procedures followed, and in the properties of the porous systems used. This paper describes an experimental investigation of permeability ratio temperature dependence, conducted to clarify some of the results obtained by previous workers. Each experiment described in this paper involved the isothermal displacement of Chevron No. 15 white oil by either nitrogen, steam, or distilled water and displacement of water by nitrogen. All permeability ratios were calculated using the Welge procedure. Values of the water-oil permeability ratio were obtained over the temperature range 75OF to 540°F. Results indicate the ratio is temperature dependent at low water saturations, probably due to interfacial effects. However, as the saturation is increased, temperature dependence decreases until, above some minimum saturation, the ratio becomes insensitive to temperature. Previously published work indicates that the dependence reappears at very high water saturations, a region of the ratio curve not completely examined in the present study. It appears that water-oil permeability ratios are temperature dependent at the extremes of the ratio curve where changes in interfacial tension with temperature induce variations in residual saturations. Between the extremes, there is a region in which the permeability ratio is insensitive to temperature. The size and location of this region is probably a function of the characteristics of the porous system. Gas-oil permeability ratios calculated from nitrogen-white oil displacement experiments indicate a definite temperature dependence over the range 75OF to 500°F and over the entire gas saturation range studied. Evidence discussed in this report indicates that this dependence is a consequence of molecular slippage in the gas phase. This is an extension of the Klinkenberg effect6 to two-phase systems at high temperatures (the existence of slippage in two-phase systems at room temperature has been demonstrated7). Evidence for a similar source of temperature dependence in superheated steam-white oil experiments

Jan 1, 1970

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By G. Bee, Z. Gavelan, R. Espinel, Y. Roditis, X. Ochoa

In August 1996 Barrick Gold Corporation acquired the Pierina property, an advanced stage exploration project, high in the Andean Cordillera of Peru and in November 1998, in a record time of just over two years, poured the first gold. After more than three years of a very successful operation at some of the lowest operating costs in the world, this presentation serves to briefly describe the project through design, construction and start-up and in particular to spotlight some of the challenges that have been overcome in valley heap leaching in a high rainfall, alpine setting.

Jan 1, 2002

By K. Wangerud, B. S. Caruso

A water balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site, South Dakota, to evaluate risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for analysis of precipitation based on historic records, and for probabilistic estimation of annual and monthly runoff from primary disturbed/mining activity areas that currently requires, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/Excel add-in “@Risk” was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation, and groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2002

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018