Search Documents

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By G. L. Smith

This paper consolidates the key elements of seven contributions, on strategic long-term planning, to two of the three international conferences on Strategic versus Tactical approaches in Mining held over the period 2005?2008. The holistic concept of strategic long-term planning as developed and implemented at Anglo Platinum is described. Consideration is given to the planning cycle, principles supporting the construction of the long-term plan, and aspects of unique best practice as developed in Anglo Platinum. Further description of Anglo Platinum?s approach to corporate governance, including the processes, methodology, systems, unique tools and techniques that are applied to value and select capital investment options is also given.

Jan 1, 2009

By J. Chirasha

Keywords: Pyrometallurgy, ferrochrome, smelting, investment, Zimbabwe Four smelting plants currently make up the ferrochrome smelting capacity in Zimbabwe. Zimbabwe Alloys and Zimasco represent more then ninety per cent of Zimbabwe?s ferrochrome smelting capacity, while Maranatha and Oliken contribute the difference. Very limited investment in the sector (even for the expansion of existing smelters) has been experienced over many years, despite the fact that about 95% of the world?s chrome ore resources are in the Bushveld Igneous Complex of South Africa and the Great Dyke of Zimbabwe. The Bushveld has a greater quantity but a lower grade than the Great Dyke. A ten per cent increase in Zimbabwean ferrochromium production has been recorded in the past ten years, showing an almost stagnant capacity investment.

Jan 1, 2011

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

The U.S. Bureau of Mines, Department of Labor, and United States National Committee of the CIE hosted the TC4.10 Mine Lighting Committee Meeting and Second International CIE Mine Lighting conference at the MSHA Academy in Beckley, WV from October 12-16, 1981. This was the first time the meeting and conference had been held in the United States. The TC4.10 Mine Lighting Committee, chaired by Dr. Adam Peretiatkowicz of Poland, was attended by 15 committee members and six guests representing eight countries. Discussion during the meeting covered mine lighting instrumentation, open cast (surface mine) lighting, and lighting sources. The committee also reviewed a draft of proposed lighting terminology and suggested changes to make the definitions more acceptable to representatives of the nations present. The mine-lighting conference featured 20 papers presented by 18 speakers representing six countries. The papers covered all phases of mine lighting, including research, hardware development and application, personnel acceptance, and requirements for system maintenance. The conference attracted 126 attendees and also included displays by eight lighting hardware manufacturers and four mining machine manufacturers. Papers from the conference are being published by the Government Printing office, with copies presented to the conference attendees. Copies will be available to others interested through the NTIS. During the course of the TC4.10 meetings and conference, committee members toured three mining equipment assembly plants, and six of the foreign representatives visited a longwall installation in an underground mine. Planning and administrative services for the meeting and conference were handled by Bituminous Coal Research, Inc., under USBM Contract H0318038.

Jan 1, 1982

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

Great new drilling results! What's so sinful about being a multi-national company? Overseas protestors flown to Australia for a free holiday How to counter the protectionist danger? Our current economic standing Over-regulation puts a convicted paedophile on the payroll The broken window fallacy Mining - A shared history Aristotle and the camels A brighter future? Something over which we do have far greater control, i.e. leadership within our own industry My challenge to you The expanding gold- producing company of which I am proud to be Chairman, Croesus Mining NL, is by definition a æmultinationalÆ. Our shareholders are based in 36 different countries, 77% of our 107 million shares are held in Australia, 23% are held outside Australia, and include New Zealand holdings of 7%. In September, Croesus Mining presented our company at the Mining 2000 Forum in Melbourne, a city caught up with multinational protestors demonstrating against multi-national companies.  

Jan 1, 2000

By R. B. Fisher

This report gives the results of mineralogical research on the Nicaro (Cuba) nickel ores and plant products. These studies were made under a cooperative agreement with the General Services Administration (GSA) of the U. S. Government. The purpose of the investigation was to obtain fundamental data that would be useful to other GSA contractors concerned with the Nicaro ores in their research on reduction roasting, leaching, and other phases of the project; and to the metallurgical staff of the Nicaro plant in Cuba. The overall objective of the combined research was to provide data to accomplish metallurgical improvement in the operations of the U.S. Government-owned plant at Nicaro, Oriente Province, Cuba. Particular emphasis is placed on improving the recovery of nickel from the ores and on the possibility of recovering other valuable constituents, especially cobalt. This study presents the physical and chemical characteristics, mineral associations, differential thermal analyses in controlled atmospheres, and X-ray studies of the ores and plant products. The nickel ores, serpentine and laterite, were from the Ramona-Lama Mulo and Ramona ore deposits. Serpentine ore consisted of serpentine-group minerals, basic iron oxide, magnetic iron oxides, chromite, olivine, enstatite, anthophyllite, cryptocrystalline quartz, wad, and a trace of calcite. This ore contained 1.6 percent nickel, 0.05 percent cobalt, 0.86 percent chromium, and 17.4 percent iron. Laterite are was composed principally of goethite with some altered serpentine, quartz, chromite, wad, magnetite, maghemite, and hematite. It carried 1.3 percent nickel, 0.11 percent cobalt, 1.9 percent chromium, and 48.4 percent iron.

Jan 1, 1959

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By Amanda Elioff

Success of the Gold Line Eastside Ex-tension rail tunnels in Los Angeles, CA has prompted the Los Angeles County Metropolitan Transportation Authority?s (Metro) planning new rail lines to include underground alternatives. The Westside Extension Transit Corridor alternatives include up to 27 km (17 miles) of subway to be constructed in soft ground. The routes will require construction in Los Angeles? ?potential methane zone,? which was not considered for subway construction until recently. Slurry face tunnel boring machines (TBM) will likely be specified.

Jan 1, 2009