Search Documents

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

By P. Burke, V. Vuaroqueaux, A. Doyle, C. Petit, Kipouros. G. J.

Magnesium and its alloys are attractive for use in automotive and aerospace applications because of their low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present work reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents results of current work on producing magnesium alloys via powder metallurgy (P/M). P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The surface layer formed on the Mg powders during processing acts as a barrier to diffusion and sintering is problematic. The layer contains oxides, hydroxides and carbonates of magnesium, formed by reactions with the atmosphere. There are several means to possibly overcome this barrier. Alloying additions have been identified that may promote surface layer disruption during sintering. Processing variables such as sintering atmosphere may reduce the layer or allow the formation of less detrimental compounds. Post-sintering processes such as hot working may disrupt the layer and improve density. The experimental effect of all these processing parameters is presented in this paper.

Jan 1, 2010

By A. Boniface

The International Tunnel and Underground Space Association (ITA) has a number of working groups (WG) that meet at least once a year. One of these is WG12, ?Use of Shotcrete?, of which the author is a member. The purpose of this paper is to draw attention to a number of topics that were discussed at the WG12 meetings held in April and September 2008; and also to a number of other matters that arose from the presentation of thirty-four papers at the 5th International Symposium on Sprayed Concrete held in Lillehammer, Norway between 21 and 24 April 2008.

Jan 1, 2008

7253. Arkhangelsky, A. D. Geological Results of the General Magnetometric and Gravimetric Surveys of the U.S.S.R. (in Russian). Internat. Geol. Cong., Rep. of the 17th Sess., Moscow-Leningrad, 1937, vol. 1, Moscow, 1939, pp. 241-250. Geophysical methods have been used in the U.S.S.R. to study geological problems. Such is the case of the general magnetometric and gravimetric surveys made jointly by the Main Physical Observatory, Main Office of Geodesy and Cartography, Institute of Terrestrial Magnetism, and Main Office of Geophysical Prospecting. Some institutions supplied the data, others processed them. Geological interpretation was made by the author. (1) Regional magnetic anomalies in the plains of the U.S.S.R. are traceable to the folded substratum overlain by sedimentary rocks; these anomalies promise to yield data characterizing the substratum in respect to strike and depth. Anomalies in European U.S.S.R. suggest that the pre-Cambrian -substratum of the East European plateau consists of elements of different ages. In the most ancient of them, the main strike of the folding is almost latitudinal; in the younger ones, the folding is oriented in the meridian. (2) The Faye and Bouguer gravity anomalies are caused primarily by differences in the density of rocks composing the upper crust and by unknown processes producing changes of density at depth; these processes are not connected with isosiatic movements. The anomalies in the European and adjoining Asiatic U.S.S.R. promise to indicate the volume of the pre-Cambrian massif of the east-European plateau and to clarify the interrelations between the Ural, Tian-Shan, and Donetz Basin folding systems, as well as between the Dnieper-Donetz depression and the mid-European depression. - V. S.

Jan 1, 1944

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

Thermodynamics of Non-Cyanide Gold Solvents The present status of the raw material base in the gold industry requires specific ways to recover gold and silver from ores. Most gold is closely associated with sulfides which require flotation followed by pressure or bacterial oxidation. The next stages of processing usually require using expensive operations for the preparation of leaching. A lot of researchers want to find a new alternative solvent for the extraction of precious metals from these products. According to the authors, one of the best ways is to use sulfur-based solvents (thiosulfate, sulfite, and their various mixtures). Thermodynamics of gold and silver thiosulfate dilution are calculated for conditions: the concentration of Au - 200 mg/L, oxygen - 3.2 mg/L, thiosulfate - 79 mg/L, OH- - 170 mg/L. the general result is the possibility of process remains under standard conditions. (erAu = = 0.035 V, ?G298 = - 29.18 kJ/g-atom ??). Silver with thiosulfate forms two strong complexes: [AgS203]- and [Ag(S203)2]3-. ?G0 = -1027 kJ/mol. The complex [AgS203]- is less stable: ?G0 = 486 kJ/mol. It should be noted that despite the high stability of gold complexes, the sodium thiosulfate may decompose to sulfite and elemental sulfur during the process, especially when heating. Gold is slightly soluble in the sodium sulfite solution, however it forms the strong complex [Au(SO3)2]3-. Depending on the concentration of free S2O32-ions, silver with sodium sulfite forms three complexes: [AgSO3]-, [Ag(SO3)2]3- and [Ag(SO3)3]5-. The dissolution speed of gold in sodium sulfite solution may be in the same range as it is during cyanidation. In this case, a practical application of sulfite process can be also used, especially for the products containing free elemental sulfur. In conclusion, sulfite-thiosulfate gold lixiviants can be used for concentrates after pressure oxidation of the cakes.

Sep 13, 2010

By Giannini M

Of the optimization techniques proposed in determining the optimum open pit limits, dynamic programming and graph theory have proved most successful. However, publications on these two methods lack a certain amount of rigour and clarity in exposition. Certain ideas in the methods have been clarified and additional features introduced in order to make them more sensitive to practical applications. A case study in the form of an application of these ideas on data from a producing mine is presented and discussed.

Jan 1, 1986

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

By H Park, L Wang

Froth flotation is one of the most widely used beneficiation processes for fine and ultrafine coals and minerals. Maintaining optimal metallurgical performance in industrial flotation operation is still a challenging task owing to the lack of an effective tool to diagnose the flotation performance in realtime. For this purpose, a number of flotation performance monitoring systems with different working principles have been developed to provide instant feedback for process control and optimisation. In this paper, for the first time, five different flotation performance monitoring systems were systematically compared through an on-site trial in a coking coal flotation plant in Queensland, Australia. The monitoring systems were used to measure (i) gas holdup, (ii) overflowing froth velocity, (iii) overflowing froth height, (iv) air recovery and (v) drag force exerted by overflowing froth, in an industrial flotation column and the outputs of these systems were collected simultaneously at a wide range of operating conditions. For each monitoring system, the best regression model describing the correlation between the system output and the flotation performance was selected from various regression models (eg linear, quadratic, power-law and logarithmic) using the Akaike information criterion (AIC). A comparison of the coefficient of determination (R2 ), residual sum of squares (RSS) and measuring accuracy at 95 per cent confidence level of the best regression models of these monitoring systems suggested that the drag sensor outperformed the other systems at a wide range of flotation operating conditions. The superior performance of the drag sensor was attributed to its distinctive design that enabled intimate sensing of variation of the overflowing froth properties. Furthermore, the drag sensor had the ability to monitor feed ash content variation when the other operation variables were set almost constant.

Aug 24, 2022

Although bismuth mineralization is spread widely through the Lachlan Fold Belt in New South Wales, broad grouping of the various deposits can be effected on the basis of geographical and geological (age and type of associated rocks) affinities. As a result, significant concentrations of bismuth can be recognized in the Mid-Western granites, Cobar-type ore, the Yass Silurian acid volcanic belt, and the Albury, Bega, Braidwoodand Bathurst districts.In these deposits bismuth generally occurs in minor amounts associated with molybdenite, wolframite, scheelite, cassiterite, chalcopyrite, galena, magnetite, pyrite, arsenopyrite, and native gold. From this group of minerals three broadly defined associations can be recognized.I. Bi-Sn-W-Mo2. Bi-Au( -Te)3. Bi-Pb-Cu(-Au)There may be some interchangeability of these metals, as instanced by occasional Bi-Cu-W-Mo mirleralization, but pyrite and/ or arsenopyrite are usually prominent in all associations.The first two of these associations occur mainly in the form of narrow quartz veins rarely averaging more than O· 3 per cent Bi, although there is often a marked enrichment in ferruginous material in the oxidized zone.Most of these veins occur within or adjacent to granitic rocks of varying ages (principally Silurian or Devonian), although Bi-Au mineralization tends to be related to more basic igneous activity than the Bi-Sn-W-Mo association.The latter is also occasionally developed in pipes, usually coarse-grained and richer in bismuth (as at Whipstick, the principal mine in New South Wales with a production of 343 tonnes of the metal), or in lower grade, but probably larger tonnage skarn deposits. The bismuth-base metal association occurs mainly in Silurian acid volcanic sequences and may also form low grade but large tonnage deposits, such as is possibly developed at Cobar.

Jan 1, 1973

By D. M. Lane, J. M. Berkoe

Engineers and Owners share a common desire to build reliable, efficient plants on schedule at reasonable costs. This paper describes one tool that Bechtel finds can integrate these objectives by “putting innovation into practice”. Examples of such innovative engineering practice include the use of computational fluid dynamics (CFD) to determine efficient designs. This paper outlines several examples of CFD applications on actual Mining and Metals Projects from around the world. The focus here is to highlight the modeling objectives, analysis strategy, actual benefit obtained from the work, lessons learned to improve future efforts and the common mistakes that can obscure the correct or best results, despite impressive graphics. The tools are powerful, and the results are more powerful when applied with skilled and well-directed human effort and ingenuity.

Jan 1, 2000

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By The Staff

THE gold mining industry in Canada is today the most important stabilizing influence in the country. This factor was brought out particularly during the 'depression' years, when steady employment was given to men in that industry and the monies spent in supplies and power in turn benefited the country to a great extent. At the same time, a commodity was produced which was saleable in any market of the world, thus maintaining Canada's credit in foreign markets and keeping her trade balances equalized. We have a vast area known as the Precambrian Shield. The agricultural possibilities of this area are practically negligible and it will depend entirely upon the mineral and forest resources to make this district an economic factor in the life of Canada. To date, from the mineral point of view, we have been highly successful. There are, however, still vast areas to be explored. It is tedious and laborious work, entailing great individual hard-ships and the expenditure of much energy and money. During my thirty years' experience in the search for, and operating of, gold mines, I have come to the conclusion that although individuals may give all their time, energy, and money, Governmental assistance is absolutely necessary in the development of hydro-electric power sites and roads. The Governments, to date, have given splendid co-operation along these lines, but in order that this great industry may go ahead they should continue their good work and, if possible, give greater relief from taxation to mines situated at a considerable distance from the railway.

Jan 1, 1938

By Gordon F. Scott

This paper considers a recently completed hoist project for IAMGOLD. Called the Westwood project, this mine utilises some of the largest drum hoists supplied to the North American Market in recent times. This project is an example of where many of the design features discussed the associated paper, (Robotham, 2011) were incorporated. Director of sales and marketing, Gordon Scott has worked at DavyMarkham for over 30 years in a variety of roles starting as a mechanical design engineer, moving to project management before joining the sales department. Gordon has an honours degree in mechanical engineering from Leeds University.

May 1, 2011