Search Documents

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By P. D. Chamberlin

Agglomeration for the heap leaching of gold and silver ores can be defined as the process of attaching fine ore particles (less than 100 mesh) to coarser particles so the fines are immobilized and uniformly distributed throughout the heap, thus making the heap more porous and uniformly permeable to the flow of a leaching solution. Agglomeration techniques and equipment to be described include drum and disc agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse running conveyors.

Jan 1, 1986

By C. Edward Capes

Fine particles in liquid suspension can be agglomerated by a number of mechanisms. Well-known methods include the addition of electrolyte to reduce the zeta potential and allow mutual adhesion arid the use of polymeric flocculants to bridge between the particles. A more recent technique, "spherical Agglomeration", is the subject of this paper. The process involves the addition of a second liquid which is immiscible with the suspending liquid and preferentially wets the particles to cause particle adhesion by capillary liquid bridges. Progress in the application of spherical agglomeration to a number of distinct technological fields is reviewed in this paper. The areas of interest include the formation of dense, highly spherical agglomerates, the separation of solids from suspension and the fractionation of complex, multi-component solids mixtures, such as ores. Some of the more interesting recent applications in the energy and environmental fields, such as the beneficiation of' coal and tar sands, are highlighted.

Jan 1, 1977

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage arc also described. IntroductionThe association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate ·formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation.In its most general form, the process of agglomeration involves taking discrete, independent particles, bringing them into contact with one another, promoting (or allowing) interparticle adhesion to occur and then causing structure rearrangement, usually under the action of external forces. The relative importance of these steps varies with the nature of the particulate system being agglomerated and with the kinds of agglomerates being produced. Coagulation or flocculation of particles dispersed in fluids is generally dominated by the contact and adhesion steps. In the granulation of powders, on the other hand, particles are already in contact so that structure rearrangement is the principal step."

Mar 1, 1992

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today's economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By Peter Ryan

A patented process for agglomeration of Smelter ESP dusts is described. Addition of suitable binders followed by compaction, transforms fine, difficult to handle material into a dry, flowable agglomerate suitable for plant reentry. Details for the agglomeration process metallurgy and laboratory pilot plant testing are discussed. An example of full scale plant operations is described.

Jan 1, 1999

By WALTER S.

(New York Meeting, February, 1912,) THE earliest example of attempting to form finely-divided materials into larger masses for better adaptation to commercial use was probably the briquetting of peat and lignite-waste at Paris by the use of a clay binder. It was from this attempt that our word briquette has arisen (Fr. la brique), the formed masses being shaped similar to ordinary bricks. This term does not, however, lend itself to the many shapes of such formed material as are now being produced, as few of them aside from some of the European brown-coal products bear any resemblance to the shape of that well-known article. The term "agglomeration " has therefore been chosen as more accurately descriptive of the products now being manufactured, this term including the molding as well as the sintering. With the increasing prices of fuel and ores and the greater demand for economy in the operation of industrial plants, more ,attention has been paid in recent years to the utilization of waste products and low-grade ores and fuels. Much of the waste has been occasioned by the inability to utilize finely ,divided ores and fuels in the furnaces because they could not be kept there, or else because they clogged up the furnace-shaft so that gases could not be forced through under ordinary conditions of operation. As a result, all such fines were thrown on the dump. Again, with the exhaustion of the richer deposits of ores, concentration of lower-grade ores becomes a necessity, and most concentrates are produced in a finely-divided condition. Aside from these considerations, there is also the economy in the cost of operating the plant; a furnace running on agglomerated material will have a much greater output than one working on fines. In one instance the charge of an iron blast-furnace was changed from fine concentrates to briquettes and the output was increased four-fold; better results could have been obtained had facilities been at hand for taking care of the increased output.

May 1, 1912

By A. E. H. Bergmann

INTRODUCTION The Sachtleben Chemie GmbH in Duisburg, a subsidiary of the Metallgesellschaft AG, operates a new sulfuric acid plant that employs fluid bed roasting of pyrite concentrates. The plant produces about 300,000 tons per year of pyrite cinders from the fluid bed roasting unit. The cinder product consists of 58 percent iron and is about 80 percent by weight smaller than 50 microns. This cinder product was found to be a competitive source material for the cement industry as the iron-containing additive. However, the extreme fineness of the cinder and its dusting tendency were undesirable and an agglomerating technique became necessary. In order to keep the price of agglomerated pyrite-cinders at a competitive level, the agglomerating method must be chosen such a way the capital and operating costs are low. Initial experiments were carried out on a laboratory scale to make an appropriate choice of the agglomerating method. Major goals of agglomerating the cinders were to improve the transportation, storage, and proportioning and metering properties. Minimum specifications are put on the size, size distribution and shape of the product. Criterion for handling is that a minimum of minus one mm. fines are produced after several handlings, while for storage, it is also desirable for the agglomerated product to survive several months in open air. Thermal agglomeration processes such as sintering one known to produce excellent products, but are by far too expensive for our application. For the same reason, granulation, balling, and pelletizing tests with addition of organic binding agents, such as tylose, starch, sulfite wash, molasses, etc. were not continued. The costs for the binding agent was considerable, which is probably due to the high pore volume of our cinders (35 %). Furthermore, the pellets or granules

Jan 1, 1977

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By J. A. Finch, J. Vergouw

"Flotation selectivity becomes progressively more difficult to achieve with decreasing particle size. One of the possible problems is agglomeration, i.e. particles clustering together. One mechanism derives from the surface charge all particles develop in water. Agglomeration driven by surface charge is known as coagulation. One form is coagulation between particles of two different minerals of opposite charge. Another is coagulation between particles of the same mineral when conditions are such that the charge approaches zero.The paper describes the method of measuring charge and a new automated settling technique for measuring agglomeration. The phenomena are illustrated with galena and pyrite. Methods of assessing the importance of agglomeration in the plant environment are still to be developed.IntroductionFine particles can agglomerate (i.e. adhere to each other) under certain conditions. This is counter-productive for any physical separation process, including flotation. One cause of agglomeration derives from the surface charge that all particles develop in water. Agglomeration due to surface charge effects is referred to as coagulation. There are two forms of coagulation. If the surface charge is brought to near zero then the force of repulsion is lost and particles coagulate. This usually applies to particles of one mineral type and the technical tenn is homocoagulation. On the other hand, if two particles have opposite charge there is an attractive force. Since the particles in this case are usually different minerals this is known as heterocoagulation.Both types of coagulation can cause minerals to be misplaced. In the case of heterocoagulation this is fairly obvious. One example that may be familiar is slime coating (fines of one mineral coating larger particles of another) But even homocoagulation can be a problem an agglomerate of the same mineral particles can entrap particles of another mineral."

Jan 1, 1997

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By Forrest W. Kinsey

The use of pellets in North American blast furnaces has made the mixes used in the associated sinter plants unique. These mixes generally contain a high percentage of fine waste oxide materials as the principal iron bearing portion of the mix, with iron ores and concentrates added in minor amounts only. Additionally, the sinter basicity is always above one and can be three or higher. This paper will discuss the large body of knowledge and experience developed by one company on this type of sinter mix. Results of laboratory tests will be used to illustrate how mix composition and feed preparation affect sinter productivity and quality.

Jan 1, 1977

By Philip L. LeHoux

"Kennecott Barneys Canyon Mining Co. is a gold heap leaching facility that has been in operation since 1989. In 1994, a flotation plant was commissioned to remove sulphide minerals from refractory sulphide ore. Tailings from the plant are mixed with oxide heap leach material in order to produce a geotechnically stable agglomerate from which the gold is leached and recovered in a conventional heap leach cyanidation process. The experience to arrive at an effective blending methodology is discussed.IntroductionAgglomeration is the practice of binding fine particles to coarser rock or other fines in order to avoid the deleterious effects of mobilizing the fines during the course of heap leaching(l-Chamberlin). Agglomeration has been considered a key component of successful operation at many heap leach sites. If the ore is of sedimentary origin and crushed, there is a high likelihood that the resulting product will contain a significant quantity of fines and a skewed gradation, that i~, a disproportionate amount of coarse and fine particles, with few in the intermediate size range. The exact methodology for determining whether the practice of agglomeration will have to be integrated into the operating scheme has been well discussed. These conditions are primarily geotechnical and geochemical. This paper will deal with the specific experiences of Kennecott Barneys Canyon Mining Company in modifying the agglomeration practices to suit evolving operational requirements."

Jan 1, 1997

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

By R. Hogg

"Some basic features of the science and technology of particle systems are reviewed in the context of agglomeration processes. Emphasis is placed on the force of interaction among particles and with their environment and on their dependence on particle characteristics and interfacial phenomena. The complex role these forces play in the various stages of agglomerate formation, growth, consolidation and structure development, and their influence on final product properties is discussed.INTRODUCTION Agglomeration is an example of a process where the technology has generally preceded the science. Process development• has very often been by trial-and-error albeit with an eye on some basic principles. Nevertheless there is' a scientific basis to the process and a better understanding of the fundamentals can surely lead to improvements in process design and control.Successful processes for the agglomeration of fine particles depend on proper control of the adhesional forces between particles, to encourage agglomerate formation and growth and to provide adequate mechanical strength in the product. At the same time the rheology of the particulate system can be critical to the rearrangement of particles necessary to permit densification of the agglomerate and the development of an agglomerate structure appropriate to the end-use requirements.AGGLOMERATION SYSTEMSUltimately, the performance, of any agglomeration process depends on the• characteristics of the particles and their environment. The specific effects, however, are often complex and may be very difficult to pinpoint by simple observation of the process. A typical agglomeration process involves a number of concurrent or consecutive steps - adhesion, growth, compaction, etc., - each of which is affected by the characteristics of the system, but not necessarily in the same way. The effect of particle size, say on agglomerate growth may be quite different from its effect on compaction and its optimum value may differ widely from one stage to the other. Obviously there.is a general need for compromise in the design and operation, of agglomeration systems. Furtnermore, an understanding of the details of the process and their complexities can be critical to process optimization and improved product quality control."

Jan 1, 1989

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By Dave H. Barnett, Brij M. Moudgil

The flotation technique as employed by Florida phosphate producing companies for the beneficiation of fine phosphate particles has been standardized over the years. Lower recoveries of coarse Phosphate rock by froth flotation technique, however, led to the development of new methods based on skin flotation of phosphate agglomerates. Recent developments of floating coarse rock in large flotation machines have not yet convinced the rock Producers of their higher separation efficiency. It is interesting to note that the selection of a particular machine is still bared on equipment preference by an individual company as well as proven performance of a particular machine for upgrading a specific material. Various techniques which have been developed to beneficiate the coarse phosphate rock have been discussed. Performance of the individual techniques is presented.

Jan 3, 1979