Search Documents

By R. J. Brailey

"A USER'S VIEW OF CONVEYOR WEIGH SCALESThe Sudbury Operations of Falconbridge Nickel Mines Limited includes seven mines, three concentrators and a smelter. The flow of ore, concentrates, fuel and fluxes between and within these plants requires measurement for accounting and control. The design, installation and maintenance .of weighing systems falls within the responsibility of the Instrumentation Department of Falconbridge Nickel Mines thus al lowing a common approach to conveyor weighing problems and the benefit of a common spares supply. This paper gives a brief overview of the recent experience with conveyor scales within the Sudbury Operations and discusses the problem areas.GeneralThe best way to establish the total amount of material going to or from a process is with a bucket and a stop watch. Unfortunately the flowrates involved in mining plants make the buckets very large, but wherever it is feasible static weighing is the preferred method of determining total quantity. This applies particularly to batch systems, where the material can be brought to rest long enough to allow a very accurate weight determination. Any form of weighing in motion is susceptible to variations in the forces of the transporting system. A belt scale is affected by its position on the belt, idler alignment, support stiffness, variations in belt tension, material spills and build-up, and a host of other factors all of which require careful consideration in any installation.As with instrumentation applied to any system the plant should be designed to ensure that the best results can be obtained from the equipment. This means getting the scale supplier together with the conveyor supplier as early as possible in the designing of a new plant. Any corners cut in scale installation will be paid for later in poor results and/or increased maintenance."

Jan 1, 1975

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

By Saulo Brinco Diniz

O presente trabalho buscou explorar a aplicação da nanoindentação instrumentada na caracterização microestrutural e mecânica de materiais metálicos. Para isso foi utilizado um ultramicrodurômetro (Shimadzu, modelo DUH–211S) e um microscópio (Olympus, modelo BX51M) a fim de analisar uma chapa laminada a quente de uma liga de alumínio 7475-T7351. De acordo com algumas das possibilidades apresentadas, pode-se concluir que a nanoindentação instrumentada é uma ferramenta poderosa para a caracterização de materiais metálicos.

Aug 16, 2017

By Lucas Breder Teixeira

O uso de ferramentas de simulação numérica para análise estrutural vem se expandindo nos últimos anos, sobretudo utilizando o método dos elementos finitos. Nesse trabalho são apresentados dois exemplos de otimização de projetos envolvendo componentes de mecanismos de válvula gaveta, realizados pela Magnesita Refratários S.A. Partindo da geometria inicial até o produto final, é analisado como o campo de tensões é adequado a valores admissíveis, conforme modificações de projeto são realizadas. Por fim, é demonstrada a importância desse tipo de estudo para alcançar maior confiabilidade e segurança em projetos mecânicos.

Aug 16, 2017

By R. Adsero

The volume of data produced by operating mines has increased substantially over the last 10 years. However, the volume of data and analytical capability has been negatively correlated to equipment productivity for at least the last seven years. In simple terms, as the volume of data has increased equipment performance has declined. Table (2010) tells us that ?The calamity of the information age is that the toxicity of data increases much faster than its benefits?. More data does not guarantee improving productivity; but more data is also not the cause of declining productivity. Similarly, when equipment performance does start to improve, (it must ? there really is no option if mines want to remain competitive), it will not be the data nor analytics which causes it; it will be the people using the resources at their disposal; including the data. Data and analytics can help if the toxicity of the data can be managed. The simplest form of business improvement using data is benchmarking. The objective of benchmarking is to understand and evaluate the current position of a process in relation to ?best practice? and to identify areas and means of performance improvement. The application of benchmarking involves four key steps: (1) Analyze and understand in detail existing processes; (2) Analyze and understand the processes of others; (3) Compare your own performance with that of the others analyzed; and (4) Design and implement the changes necessary to close the performance gap(s). There are however, many in the mining industries who have shunned equipment benchmarking because they believe that, ?every mine is a pilot?. In other words, the differences between mine operations make comparisons between them of little value. This paper will present a valid approach to benchmarking equipment performance and reliability, accounting for the differences and similarities between operations, producing a result which can be used to add value to mines around the world.

Feb 23, 2014

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

By Ning Zhang, Yan Chen, Qikang Yi, Linjian Ma, Guoan Wang

Laboratory tests were performed to explore the effects of frequency on the deformation property of rock salt subjected to cyclic loading under confining stress condition. A two-stage (transient and steady) evolution law of axial cumulative strain was obtained through cyclic stress-strain curves complied from the loci of minimum load of each cycle. The unloading modulus decreases with loading cycles/time as a negative exponential function. The damage of rock salt under cyclic loading is reflected by the degradation of elastic modulus. A unified damage evolution equation considering the effects of frequency and time was established based on the experimental results. A new creep damage model for rock salt was proposed by introducing the non-stationary modular components in Burgers creep equation according to the Lemaitre equivalent strain theory. Comparative study indicates that the new model can accurately describe the creep deformation and damage evolution of rock salt under different loading frequencies. This paper provides a more reasonable model and relevant mechanical parameters for the stability analysis of compressed-air storage cavern in the injection and withdrawal durations.

Jan 1, 2015

By R Simonato

It is now recognised that rotary sample division is by far the best laboratory tool for extracting subsamples from a lot of material. In terms of sampling theory, rotary division, by virtue of the fact that it can extract many increments from the lot during the division process, radically reduces the variance due to distributional heterogeneity in the sample being divided. There are a number of occasions in sample preparation when it is necessary to extract a subsample of a target mass. To do this with rotary dividers taking a fixed fraction of the starting mass is a tedious task. In response to this problem, a variable split sample divider has been designed and built for the mineral industry. This paper discusses the utility of the device and presents test data showing that the machine is capable of making accurate mass split while overcoming segregation in the material being divided.

Jan 1, 2008

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the Fundamental Sampling Error (FSE)–, Duplicate Sampling Analysis (DSA) and Segregation Free Analysis (SFA)–, are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody was calibrated using the DSA and SFA methods and the results compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to the power of 3. A later modification of Gy’s formula raises dN to the power (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of in the range 0.97 to 1.30. The average value for is shown to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry-preferred 1.5. It is suggested that for low-grade gold-bearing ores the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the FSE greatly simplifies the characterization of gold ores, now requiring only the calibration of K for a given mass and established fragment size. The implications of the simplified equation for the heterogeneity test are that, provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.

Jan 1, 2017

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That sub- ject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public atten- tion has focussed as never before on the subject of commodity prices. To advocate stabilizing com- modity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent f.11 1k

Jan 1, 1978

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By John V. Beall

GOING west from Denver on Route 6, the direct road to Grand Junction, one gets the first glimpse of mining a few miles east of Denver near Idaho Springs where the workings of defunct gold mines are visible on the sides of mountains along the highway. One enterprising company is turning a profit by showing tourists through the mine and mill and then selling them gold samples on the way out. We have always known that mining people are ingenious, but this proves it. About five and a half hours fast driving west from Denver brings one to Rifle, Colo., which is the site of the oil shale mine, retorting plant, and refinery of the U. S. Bureau of Mines. As you drive up to the mine, you can see a portal high on the face of the cliff in front of you where the mine surface plant literally hangs by its toenails. Below, the retorting plant and refinery gleam in the sunlight. Up at the mine, Fred Wright will show you how the oil shale is extracted in two benches (a third bench would be used for commercial mining) by the room-and-pillar method. In mining the top level, an underground crew of thirteen men have been able to produce 1500 tons of shale in each eight-hour shift. To do this, the mine is thoroughly mechanized. The mining method is de- scribed in the September issue of Mining Engineering.

Jan 1, 1949