Search Documents

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

Contact Angle Measurements on Lignite Surface

Sep 13, 2010

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

Jan 1, 2006

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By C. E. Melbye

A serious problem confronted the city of Gunnison early in 1958 in that, for a few months during each spring runoff, the water supply derived from the Gunnison River became polluted to an unsafe point. The city management had the choice of building a new filter plant to replace the old unworkable one or drilling wells to develop a ground water supply. The cost of a new filter plant was estimated at $180,000 compared to $50,000 for 6 wells, pumps, and additional water lines, hence their decision to attempt the development of sufficient ground water. Six wells at 300 gpm per well were estimated as necessary to handle the peak usage of 1800 gpm, compared to only 600 gpm winter usage. Although the water table is only about 7 feet below the surface, existing private wells drilled at random locations were producing much less than 300 gpm. The problem was to find sufficient quantities from about 6 wells. Since the presence of an ancient bedrock channel was suspected, which would be expected to localize greater quantities of water, the city of Gunnison authorized a resistivity survey to investigate bedrock topography below unconsolidated gravels. Survey results were highly satisfactory and led to the preparation of a fairly detailed bedrock contour map, Fig. 1. This map was used in selection of all well sites. The city of Gunnison is situated in a flat, broad, Quaternary gravel-filled valley (terrain dips south at 20 feet per mile) at the junction of the Gunnison River and Tomichi Creek. The valley, about 2-4 miles wide, is bordered by hills of Tertiary volcanics to the northwest, Cretaceous and Jurassic sediments to the north and northeast, and pre-Cambrian granite and gneiss to the south. One previous deep test well at the west end of the city hit pre-Cambrian granite at 496 feet, which, allowing for 40 feet of surface gravels, makes the older sedimentary section 456 feet thick. This section is probably all Jurassic Morrison formation, consisting of the Saltwash sandstone overlain by the much thicker section of Brushy Basin shales and mudstones. According to the driller's logs, each well was bottomed in what is believed to be Brushy Basin shale. FIELD PROCEDURE A standard Gish-Rooney type of resistivity apparatus was employed, which used 45-volt dry batteries as a direct-current power source. Applied voltages could be selected from 45 volts to a 270-volt maximum. Copper-coated steel stakes were employed as current electrodes and porous porcelain pots as potential electrodes to avoid possible polarization effects with direct current. The expanding Wenner electrode configuration was utilized for this investigation and measurements were made at 20 40, 60, 80, and 100-foot spacings,

Jan 1, 1961

By J. E. Dutrizac, J. B. O'Reilly

"Zinc is a relatively abundant element which occurs as both high-grade sulphide ores {sphalerite ZnS) and oxide ores which the ancients collectively termed ""calamine"" (smithsonite ZnC03 and/ or hemimorphite Zn4Si201(0H)2 - H20 and/ or hydrozincite Zn5(C03) 2(0H)6). Although oxidic zinc is readily reduced by carbon, the process becomes thermodynamically viable only at - 1000°C, and at this temperature the zinc is released as a vapour (B.P. 907°C). Casual cooling of the vapour results in its re-oxidation by excess combustion air or even the carbon monoxide product of the reduction reaction. ZnO + C = C09,, + Zn vapom Only fairly rapid quenching of the zinc vapour and the isolation of the reduction products from the combustion gases will yield metallic zinc; these conditions were not produced deliberately until the advent of distillation technology. Until quite recently, the principal use of zinc was in brass manufacture; galvanized iron was not discovered until the 19th century and zinc casting alloys are a relatively recent invention. As will be seen, brass could be produced without recourse to a pure zinc intermediary, and the discovery of brass preceded that of zinc by many centuries. The purpose of this paper is to outline the discovery and early development of both zinc and brass with special reference to the European scene."

Jan 1, 1999

By William J. Purdy

Successful design, operation and completion of a surface waste management facility for a diamond mine located in Canada?s northern environment requires careful planning to minimize short and long term environmental impacts. As part of the mine development application process, best practice standards were applied using conventional engineering to reduce the environmental effects of the mine waste facility at the Snap Lake Diamond Project. This paper presents the design criteria, site conditions, material characteristics and engineering management objectives considered for optimization of the development plan. Insight into the engineering analyses, development alternatives, monitoring program and reclamation strategy plan to be undertaken during mine operations to provide opportunity for adaptive management and to minimize environmental impacts is provided.

May 1, 2004

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the information needed to use the Wearing Hearing Protection Properly 3-D training reel. It offers practical suggestions on how to use the reel as a training aid, performance objectives for deciding if the training is appropriate for your needs, and discussion notes that provide additional information to the user. The 3-D reel was designed as a self-teaching aid that drillers and others who work at a drill site can use wherever the opportunity for such training presents itself. The latter could be a company preshift requirement or a tailgate session where workers would have an opportunity to view and discuss the reel. It could also be an individual looking at the reel in a pickup truck prior to beginning work at a drill site. The 3-D training reel is versatile in that it can be used for a small group of persons or for a single worker. For any of these situations, information is transferred to the individual by viewing each of the seven colorful, in-depth 3-D scenes and relating the words that appear in each scene to what is depicted in the visual. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 11, 2004

By M. Arvola, A. Mäkinen, N. Isomäki

Arsenic is a compound that has no significant market value. However, it needs to be removed from ores, concentrates and other process streams because of environmental or technical processing concerns. A wide range of arsenic containing minerals exists in nature, and in many instances these minerals are also associated with the ones that have commercial value. For example, sulfide copper ores are normally closely associated with minerals like enargite, Cu3AsS4 and tennantite Cu12As4S13. After mineral processing these arsenic sources can report to the waste waters and these effluents need to be treated before discharge or recycling. Ferric arsenate precipitation is a well-established method for stabilizing arsenic in effluents. Electrochemical arsenic removal utilizes the same adsorption/precipitation ideology as ferric arsenate precipitation. Electrochemical arsenic removal, even though it is a simple process in terms of equipment, is a complex system involving chemical and physical mechanisms taking place simultaneously to remove dissolved and/or solid arsenic components from wastewaters. The whole process can be described by the following three steps: 1) electrolytic oxidation at a sacrificial anode (dissolving electrode metal, iron for example), 2) chemical reaction between dissolved iron and arsenic to form a solid precipitate and 3) aggregation of the particles to form flocs, which can be removed by known solid/liquid separation methods. Electrochemical arsenic removal is a very efficient way to remove arsenic from different waters to very low residual concentrations.

Jan 1, 2016

In this address I look back over the past 40 years of mineral exploration in New Zealand û essentially the period since the Second World War (ie since 1945). It was the period of my personal involvement, and indeed of the personal involvement of a number of you. Luckily it was aperiod of great interest and activity. In the previous 50 years, virtually nothing had happened, and it is kindest to draw a veil over that period. In the very important earlier 40 years (1855 - 1895) the New Zealand gold rush occurred. That must have been a fascinating, rewarding period, which has been thoroughly documented by better historians than myself. I will simply comment firstly that its mineral explorers (gold-prospectors) were very successful indeed, and found most localities of the minerals they sought, in spite of using very different methods from ours of today. Secondly, they were preceeded by one of Maori exploration, which searched for a much restricted list of minerals, but succeeded in finding virtually every locality we know of today. The explorers of both of these early periods were obviously highly successful, but, in the time available, I must restrict myself to the period since 1945. I am currently editing the effective up-dating of Gordon WilliamsÆ 'Economic Geology of New Zealand' (1974). It covers the last 12 years or so. Many of you are contributing to that volume û both as authors and as referees û and I would like to take this opportunity of thanking you all. Although this new volume excludes the energy field, many of us have been involved in it, and I am therefore including energy minerals in this review, as Williams did in 1974.

Jan 1, 1987

By Don Dodds

Iron Mountain Mine Rehabilitation Project Brief History The Iron Mountain Mine is located in Northern California approximately 12 miles northwest of Redding. The ore body is a large, very dense pyritic intrusion, discovered in 1860, and initially minded for silver. The silver played out quickly and 34 years later the ore body was mined for copper. Copper mining was scheduled to cease in 1939, but WWII prolonged the closure. After WWII, the pyrite ore was mined to produce sulfuric acid. In 1949 when large amounts of cheaper sulfuric acid were being generated by the oil industry the underground mine shut down. Little was done with the site conditions until 1970 when the U.S. Bureau of Mines began monitoring the pH of the effluent. The initial pH readings were around 2.0. This was lower than anyone expected. Laboratory tests showed that when the ore from the mine was submerged in water, the pH of the water would stabilize above 4.0. However, the pH got steadily lower. In 1989 with the ph around 0.7, the U.S. Environmental Protection Agency (EPA) required the owner to build a capture and treatment facility. During this initial period, the majority of the effort was spent on the treatment plant. The relationship between the mine owner and the EPA was basically an adversarial relationship from the very beginning. In 2001, North Pacific Research was hired to upgrade the capture and control facility. The general layout of the Iron Mountain Mine is shown in Figure 1.

By C. A. Johnson, K. F. Unrug

The identification of the major subsidence areas in the Eastern Kentucky Coal Field has been made to distinguish the subsidence phenomena on the basis of geographical location. Further, this identification process is based upon selected critical geological, topographical, and mining features in the coal fields. The proposed identification of the regions is derived from a comparison of the subsidence potential in a particular area. The most likely severe subsidence areas are compared to those with the probable low subsidence severity. The combination of certain geological and mining parameters involved allows for the derivation of a classification of the subsidence potential.

Jan 1, 1986

The paper point out the testwork has been carried out with real process solutions from the Chambishi cobalt plant in Zambia, showing that the ISEP® continuous ion exchange system can effectively remove nickel from cobalt sulphate electrolyte. Laboratory testing confirmed published data, and was subsequently verified on site at Chambishi in a pilot test program. Based on the testwork data, a commercial unit is being installed at Chambishi.

Sep 13, 2001

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996