Search Documents

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By M Bird, B Oats, M Sganzerla

Mining operations are continually aiming to reduce operating costs to improve plant profitability. One way in which the Cannington operation sought to achieve this was by increasing the wear life and reducing the energy consumption of their flotation mechanisms. This was made possible using Outotec’s FloatForce mechanism. The FloatForce mechanism has been developed by Outotec over a six year period involving both CFD modelling and rigorous site testing. FloatForce delivers improved air dispersion and cell agitation efficiency; as such it can be operated at lower rotor tip speeds when compared to Outotec’s previous mechanism.Cannington trialled three FloatForce mechanisms in a train of ten OK38 zinc roughers. The mechanisms’ rotational speed was reduced by 10% compared to the previously installed MultiMix mechanisms. The purpose of the trial was to quantify the energy saving and assess whether there was any reduction in plant metallurgical performance.The trial was successful with FloatForce delivering a 17% reduction in power, an improvement in wear and improved recovery. Analysis of pre and post-installation metallurgical accounting data showed the following:The FloatForce installation resulted in a recovery increase of zinc to zinc final concentrate of 0.4 – 4.0%*The FloatForce installation resulted in a recovery increase of lead to zinc final concentrate of 0.0 – 0.3%*There was no statistically significant change in silver recovery to zinc final concentrate that can be attributed to FloatForce**95% confidence interval (CI) using multiple linear regression models.The Cannington operation is now in the process of further optimizing its power consumption and wear savings by changing the remaining OK38 zinc and lead rougher float cells to FloatForce mechanisms.CITATION:Bird, M, Oats, B and Sganzerla, M, 2015. Improvements in flotation cell maintenance, power consumption and operation at South32 Cannington, in Proceedings MetPlant 2015, pp 230–245 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The State of New South Wales is highly favoured in having vast deposits of coal adjacent to and within easy reach of the coastal Ports. Not only is the quality of the fuel generally superior to any found in the other States, but it is greater in extent than in any other part of the Continent. For interesting and reliable details of the history of the discovery of coal, the geology of the coal bearing strata, analysis of the various coals and other valuable data, the readers are referred to the book recently issued by the New South Wales Government, entitled The Mineral Resources of New South Wales, by Edward F. Pittman, A.R.S.M., etc., by the direction of the Hon. T. L. Fegan, Minister for Mines. The mining community is indebted to the Minister for having had published the most valuable condensed record of the mineral resources of the State extant.For the purposes of this paper we will only give such a general description of the coal fields as will make it intelligible in connection with the subject of the coal mining in the State of New South Wales.

Jan 1, 1904

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

THE method depends upon:--1. The position of the mill.2. The space available for stacking the residue.3. The nature of the residue as discharged from the mill.4. The value of the residue for re-treatment.5. The requirement of the residue for underground filling.Originally the conditions in this district varied mainly in the position of the mill, some mills having an elevated site with plenty of dumping space for the time being, whilst others had a flat site, and very little dumping space near at hand; but in most cases the residue discharged was in the form of filter-press cakes, suitable for conveying on belts, or in trucks, and stacking in a high clump; and, while a portion of the residue was used for underground filling, the dump was regarded as a valuable asset, to be re-treated later. Under these conditions, conveyor belts, electric trams, aerial trams, and hose trucks, all gave satisfactory results, and the following figures, taken from "'West Australian Metallurgical Practice," will show how these methods compared as regards costs...

Jan 1, 1909

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By D C. McPhail, S L. Rogers, J Brugger

Using iron- and sulfur-oxidising bacteria to catalyse the breakdown of sulfides that host the gold is an important biological method for the pretreatment of refractory gold ores. Following this biological treatment a combination of chemical and physical methods are used for leaching (such as the cyanide process) and concentration (such as carbon-in-pulp or electrowinning) of gold. Although these methods are well accepted by industry, they harbour limitations in the processing of low-grade refractory ores, and regulatory agency/public acceptance of cyanide use. Thus, it is beneficial to industry to develop environmentally friendly, cost-efficient leaching and concentration techniques that are based on micro-organisms. This may soon be possible by adapting the results of recent regolith geoscience research, which has shown that micro- organisms are capable of driving a biogeochemical cycle of gold dispersion, transport and reconcentration in the supergene environment. The indigenous microbiota in biologically active soil microcosms from a number of Australian sites are capable of solubilising up to 80 wt per cent of the gold contained in these materials during 50 days of incubation. Studies using molecular microbial techniques have shown that a metallophilic bacterium, Ralstonia metallidurans, is present in biofilms on gold grains from a number of Australian sites. R metallidurans is capable of actively accumulating gold from solution, suggesting that the bacterium may contribute to the formation of secondary gold grains and nuggets. Identifying the biochemical and physiological pathways that lead to the dispersion and accumulation of gold in regolith, and quantifying the reaction kinetics of these processes may thus lead to the development of industrial bio-processing capacities for gold-containing ores.

Jan 1, 2007

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003

By Winton Gale, David Oyler, Jinsheng Chen, Christopher Mark

The National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tailgate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By Maurice Bottiau

The recent evolution of the piling market clearly shows a growing demand for screw piles with soil displacement. The recently developed Omega Screw pile ful-fill these new expectations, combining the advantages of vibration-free systems and the behaviour of a displacement pile. The paper describes recent experience and new applications with this very promissing pile. Full-scale load tests were carried out in different countries as U.K. or Sweden. A very attractive and innovative piled embankment is also described, using geogrids in order to transfer the loads from the superstructure to non-reinforced Omega-piles.

Jan 1, 1996

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003