Search Documents

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By R. W. Fedors, S. T. Green, F. T. Dodge, D. B. Walter

Spatial and temporal temperature variations in a high-level radioactive waste repository drift can give rise to moisture transport within the drift. Knowledge of this moisture transport may be important to assessing the potential for corrosion of all metallic components in the drift. The model presented here shows one approach to simulating evaporation, transport, and condensation of water in large underground openings using a framework based on computational fluid dynamics. Simulation results that explicitly model water and latent heat transport are presented.

Jan 1, 2004

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By D. Scott Scovira, Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance.

Jan 1, 2010

By D S. Scovira

The effect of blast vibration on highwall stability is a common concern for many open pit mines. Vibration in such a case is a typical near-field blast vibration situation. Vibration modelling in the near-field of a blast requires consideration of both the amplitude and frequency attenuation of waveforms with distance. Most existing blast vibration models are designed for far-field vibration and do not simulate the frequency attenuation and its effect on waveform shape. With the advent of electronic detonators it is desirable to quantify the effects of blast delay on the amplitude as well as the frequency of blast vibrations. A suitable modelling tool is proposed here. At present, a blast vibration model with double attenuations(amplitude and frequency) has been developed at Orica. The present model simulates the amplitude and frequency attenuations separately using different transfer functions. The amplitude attenuation is modelled according to the non-linear relation between the peak particle velocity (PPV) and the charge weight scaled distance established from the signature hole vibration. The frequency attenuation is modelled with the signal broadening based on KjartanssonÆs transfer function û a linear model for attenuation of waves. The model is capable of taking multiple sets of signature waveforms as input to improve the modelling accuracy of the wave propagation in the geology at a site. The screening effect of the earlier firing holes in the path of a later firing hole is taken into account on not only the amplitude, but also frequency attenuation. The present blast vibration model is suitable for modelling both near-field and far-field blast vibrations. It yields reasonable agreement with measured field data for the near-field vibration examples discussed.

Jan 1, 2007

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By A. D. Hill, R. S. Schechter, M. P. Walsh, I. H. Silberberg, M. J. Humenick

There are many uranium deposits which are too deep, too poor in quality or too small in extent to be economically strip mined. It now appears that this uranium can be mined using in situ leaching processes. A number of field tests have been, are being or will be conducted to demonstrate the feasibility of In site leaching. Preliminary results are encouraging, but a major question concerns the restoration of the mine site, which is generally contained within an aquifer. It is necessary to ensure that the quality of the water is not adversely affected by the mining operation. One component of the lixiviant is necessarily a cation and, during the course of mining, the ion exchange sites of the minerals in the mine zone become saturated with this cation. Ammonium is the cation now commonly used. Clearly, any restoration procedure or question involving the rate of cation migration with the groundwater all necessarily involve the process of ion exchange coupled with flow in porous media. The equations describing this process are presented in this paper and numerical solutions obtained. Preliminary results showing the effect of isotherm shape, cation exchange capacity, flow and dispersion are presented. These results demonstrate that in many situations cation migration in ground water will be slow.

Jan 1, 1979

By James A. Berberick

Research methods to develop an economic model for the determination of regional mineral advantage are discussed. An industrial complex conceptual framework is used to study potential mineral resource outputs of Kansas. A procedure for making a comparative cost analysis of potential outputs for a Kansas-based industrial complex is outlined and illustrated. Methods for estimating aggregate demand and for developing an input-output matrix for a hypothetical limestone complex are explained. The input-output matrix is expressed in physical units. A computer algorithm for converting physical production data and input cost data into total cost per unit of output information is briefly explained and flowcharted. Limitations and usefulness of this procedure in determining regional advantages are surveyed.

Jan 1, 1969

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By Z Chang, S A. Mrozek

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Antamina, Peru is the largest Cu-Zn skarn deposit in the world. Skarn mineralisation is focused around a multiphase Miocene intrusive complex comprising at least eight distinct phases identified by cross-cutting relationships, including truncated veins, xenoliths and chilled margins. Skarn alteration and mineralisation, as observed in drill core, remain open at depths exceeding 2.2 vertical kilometres.Porphyry intrusions occur as four major phases with subphases (from oldest to youngest): P1 (a, b), P2 (a, b), P3 (a, b) and two dykes of uncertain timing named Oscarina-1 and Oscarina-2. P1a is a hornblende-biotite quartz diorite porphyry with pervasive K-alteration, local endoskarn and 30–40 per cent sheeted quartz veins, all of which obscure original igneous textures. P1b dacite porphyry is a minor unit with <10 per cent phenocrysts and <3 per cent quartz veins. P1b cuts P1a; P2 dykes cut both units. P2a porphyritic biotite quartz monzonite contains K-feldspar megacrysts up to 4 cm long, local K-alteration and 2–80 per cent quartz stockwork veins. P2b biotite monzonite porphyry contains approximately 50 per cent phenocrysts and typically <10 per cent quartz veins. P3a (brown groundmass porphyry) and P3b (coarse phenocryst porphyry) are minor in volume and extent, and both cut P2 bodies. Oscarina dykes comprise two separate but parallel bodies. Oscarina-1 is a feldspar-phyric rhyolite porphyry, while Oscarina-2 is an intensely chloritised andesite porphyry. Oscarina-1 has a U-Pb (laser ablation inductively coupled mass spectrometry (LA-ICP-MS)) age of 10.1 ± 0.1 Ma, whereas P2 U-Pb zircon ages (LA-ICP-MS) range from 10.0 ± 0.2 Ma to 9.9 ± 0.3 Ma.All the intrusive phases contain quartz veins, with P1a and P2a having the most intensive K-alteration and most abundant quartz veins ± endoskarns. Each phase may have contributed to mineralisation at the right depths and within favourable wall rocks (ie marble) during uplift of the Antamina structural block. Therefore, a model of multiple intrusions during continuous uplift explains the vertically extensive (>2.2 km) skarn and mineralisation at Antamina.CITATION:Mrozek, S A, Chang, Z and Meinert, L D, 2015. A model for the intrusive sequence and Cu-Zn skarn formation at the Antamina deposit, Peru , in Proceedings PACRIM 2015 Congress, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Nickolas Vlahopoulos, Nicholas Stowe

A concept has been proposed for the focusing of underwater energy. An array of spherical TNT charges is used to achieve this aim. The goal of the present research effort is to model such a system and identify optional arrangement and detonation timing schemes. A fast-running model is necessary to perform optimization analysis due to the highly iterative nature of most optimization algorithms. This requirement renders the use of sophisticated numerical solvers impractical. An analytical, physics-based model must be developed to satisfy the demands of the multiple charge optimization problem. This model must capture shock propagation speed, pressure-time histories throughout the fluid domain, and multiple charge interaction phenomena. Such a model is presented herein.

Jan 1, 2012

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By Otuonye F

An outburst is the spontaneous ejection of pulverized coal and gas from the working face in an underground mine. It is caused by overstressing the rock, due predominantly to the influence of geological structures on in situ stresses, stress concentration from the excavation and overburden load on mine openings, and large volumes of gas sorbed in the rock. The spontaneous release of high pressure gas creates intense shock waves which may cause damage to the mine ven- tilation system and the pulverized rock/coal ejected may cause injury or death to miners. The gases emitted pollute the mine air and may also result in death to miners.

Jan 1, 1988

By Renato G. Bautista, KNona C. Liddell

A model of the reaction of chalcopyrite, CuFeS2, with Fe3+ and with 02 is considered. Homogeneous solution phase reactions are assumed to be always at equilibrium throughout the dissolution of the mineral. The dissociation of USOb- and several complexation reactions involving cu2+, Fez+ and Fe3+ are incorporated in the model equations. The relative importance of Fe3+, 02, and H+ as oxidants and the role of solution equilibria are assessed and the implications for leaching practice discussed.

Jan 1, 1981

Various aspects of judgment and decision-making are key themes in this book. The model presented here serves as a loose structure for the chapters that follow this one. The notion of a model is introduced because growing research interest in the subjective aspects of group and individual behavior has led to a debate over whether judgment is a skill that can be understood scientifically. A related point of contention is whether such an understanding could lead to the development of methods for estimating people's ability to make good decisions during an emergency. There is some literature that supports the potential usefulness of this approach. However, little agreement seems to have been reached on how to define and operationalize even those basic concepts necessary to assess the soundness of decisions from within their environmental and group contexts [Jensen and Benel 1977; Godden and Baddeley 1979; Baumann and Bourbonnais 1982; Brecke 1982; Stone et al. 1985]. A look at the real-world process is clearly needed. The need to attempt a better understanding of judgment and decision-making properties stems from those occasions in the existence of an organization when there is a lot at stake. The process of decision-making (which is part of the exercise of judgment) has been analyzed in situations such as corporate takeovers [Janis and Mann1977], military combat [Begland1979], clinical emergencies [Baumann and Bourbonnais 1982], and aviation events [Billings and Reynard1984]. The fundamental assumption of these analyses is that, while there are untold successes, there are also notable numbers of failures resulting from decisions that can be ascribed to one or more errors in judgment. From a cognitive perspective, any person engaged in decision-making (either alone or in a group) is actively involved in a process characterized by certain elements. These were mentioned in chapter 1, but are reiterated briefly at this point: (1) detection of a problem, (2) definition or diagnosis, (3) consideration of available options, (4) choice of what is perceived as the best option given recognized needs, and (5) execution of the choice based on what has transpired [Flathers et al. 1982; Baumann and Bourbonnais 1982]. At any moment in this process, there are factors at play that have a large impact on one's ability to solve complex problems in a limited time: (1) an internal state [Hedge and Lawson 1979] is the sum of a person's psychomotor skills, knowledge, attitudes, etc.; (2) uncertainty [Brecke 1982] is caused by faulty or incomplete information received from the external environment; (3) stress [Biggs 1968; Jensen and Benel 1977] is generated both by the problem at hand and any background problem that may exist; and (4) complexity, as it is used here, refers to the number of elements involved that must be attended to. These variables are depicted in figure 5.1, and their relationship to each other and to an outcome is indicated. This schema is designed to suggest interaction, because while the judgment and decision-making process may be conceptualized as discrete stages, experience tells us that this is not the way people function in real-world situations.

Jan 1, 2000

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995