Search Documents

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

Resonance re-emission from nickel vapour affords a convenient method for isolating the resonance lines at 3415A, 3515A, and 3524A. The vapour is generated by cathodic sputtering and is illuminated by light from a nickel atomic spectral lamp. The resonance lines thus isolated can be usefully employed for absorption measurements on mineral samples where the nickel concentration is too high for measurements with the more sensitive line at 2320A. A spectrophotometer employing a resonance lamp as monochromator possesses several advantages where a great number of determinations are made under routine conditions. The wavelength setting is stable under even the most rigorous conditions and with the provision for automatic setting of full scale deflection the instrument requires virtually no adjustment. The instrument has been used under routine conditions for the determination of nickel (in the range O· 05-2 per cent) in mineral samples.

Jan 1, 1968

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By B M. Moudgil

Atomic force microscopy (AFM) has become an important tool for understanding the nano- to molecular scale mechanisms predominant in multiphase systems. In flotation research, the use of AFM holds promise for unlocking and establishing fundamental mechanisms, ultimately leading to significant advances in process performance. From measuring and characterising surface forces, the structure of molecules at interfaces, and nanoscale features on flotation media, AFM is a powerful tool that has only begun to impact flotation research. Highlights of advances made in the utilisation of AFM for flotation research at the University of Florida are given with an emphasis on interpreting the mechanisms behind calcium activation in phosphate flotation and the impact of nanoscale asperities on collector-born surface hydrophobicity.

Jan 1, 2005

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the 'wet zone' with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By D. Norval, J. J. Dunkley

The process of atomisation is introduced and related to granulation. Some processes applicable to ferroalloys are discussed, along with their limitations and advantages. Examples of applications of atomisation to the processing of ferroalloys, including ferrosilicon and ferromanganese for use in the welding industry and as injectable additions to steel or cast iron are also presented. The economics of the process and the impact of process scale are discussed, along with criteria for process selection and system design.

Jan 1, 2004

By Manabu lshimaru

Solid-liquid interfaces as well as defect formation processes during crystallization of melted silicon (Si) have been examined by using molecular-dynamics (MD) simulations. The ordinary Langevin equation employing the Tersoff interatomic potential was used for the calculation of the atomic trajectories. A solid-melt interface has a tendency to form {]] I} microfacets during the crystal growth in the [001] direction, while it is essentially flat during the (Ill) crystallization. Because of the difference of the interfacial structures, the structures of grown-in defects and defect evolution depend strongly on the growth direction. We discuss defect structures and their formation processes within the context of our results as well as previous experimental observations.

Jan 1, 2001

By Hani Henein

Recent innovations in atomization of molten metals have occurred in the area of single fluid atomization. Impulse Atomization (IA), one of the single fluid techniques, provides unique capabilities to study different regimes of atomization in a controlled environment. By changing processing variables, a mono-dispersed distribution of droplets above one millimeter in diameter can be produced. This is accomplished through proper characterization of the forces influencing the process and in particular the flow of melt through the orifice. This paper will discuss the approach and illustrate results with molten aluminum and cobalt.

Jan 1, 2006

By Samuel Filgueiras Rodrigues, Sebastião Raimundo de Jesus Belém leitão Filho, Gedeon Silva Reis, Eden Santos Silva

Nesse trabalho estudou-se o retardo na cinética de amaciamento estático do aço inoxidável austenitico ASTM F-1586 (ISO 5832-9) usado na confecção de implantes ortopédicos, por meio de ensaios de torção a quente isotérmico em duplo passe. Inicialmente as amostras foram aquecidas por indução até a temperatura de 1250 oC e mantidas por 300 s para solubilização, em seguida resfriadas até a temperatura de deformação (Tdef), que variou de 1000 a 1200 oC, com passes de deformações de ε1 = ε2 = 0,30, taxa de deformação de 1,0 s-1 e tempo entre passes (tp) variando entre 0,1 – 1800 s, simulando um processo de forjamento a quente industrial de um dispositivo ortopédico. Os resultados da simulação física do processamento termomecânico indicaram que 60 % do amaciamento dá-se por recuperação estática (SRV), com moderado valor de energia de falha de empilhamento (γEFE ~ 69 mJ/m2) do aço e tempo de encubação pra iniciar a recristalização estática (SRX) maior que 10 s abaixo de 1100 oC com formação de patamares nas curvas de amaciamento Xs vs tp, indicando atraso na cinética de recristalização estática (SRX) resultante do efeito dos precipitados da fase Z (NbCrN) induzidos por deformação nos contornos dos grãos austeniticos.

Nov 18, 2019

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946

By E. W. Sawyer

Attapulgite is a magnesium aluminosilicate clay mineral which exhibits unique, processing-enhanceable physical and chemical properties that are related to its current commercial uses. Properties of commercial interest are gelling, absorption, adsorption, binding, acid neutralization and many others. Major industrial applications are: (1) absorption by heat treated grades utilized in industrial oil and grease absorbents and in agricultural pesticide carriers; (2) gelling of aqueous liquid products by colloidal grades for stabilization and viscosity control in salt water drilling fluids, suspension fertilizers, liquid animal feed supplements, paints and tape joint compounds; (3) adsorption by heat treated varieties for the removal of catalysts, color bodies and other polar compounds from hydrocarbon streams; (4) gelling of organic liquids by colloidal attapulgite/surfactant blends in oil-type paints, fibrated and nonfibrated asphaltic coatings and mastic compositions, and (5) the binding of feeds and molecular sieve sorpents with colloidal type attapulgite products. These applications and other less common uses and potential uses will be discussed along with, the necessary selective mining and plant processing features related to each property and application.

Jan 1, 1986

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

For the first time, the attendance at the meetings of the Institute passed the thousand mark; as is shown by the following table: REGIS- AT BANQUET DID TOTAL TERED NOT REGISTER Men :..:... 703 76 806 Women 195 61 256 1062 The names of the members and guests who registered or attended the banquet but did not register are: A A. D. Beers C. A. Adams Hans Behr Thos. J. Adams Edgar G. Bell Lawrence Addicks Donald A. S. Bell H. T. Abrams W. de LeBenedict G. Aertsen G. B. Bertelli M. M. Albertson Charles P. Berkey James Aldrich Clinton Bernard D. C. Alexander, Jr. W. N. Best W. H. Alexander Robert M. Betts A. W. Allen Christopher H. Bierbaum F. D. Aller Paul Billingsley R. H. Allport R. A. Bingham F. C. Alsdorf R. M. Bird Capt. M. Altmayer John L. W. Birkinbine A.' W. Ambrose G. S. Bisey Henry M. Ami Charles W. Boise F. L. Antisell J. J. Blackmore R. S. Archer A. E. Blackwood Paul' Armitage Capt. C. K. Blatchly Andrew B. Armstrong E. L. Blossom Clifton T. Armstrong C. A. Bohn Ralph Arnold James M. Bonsall R. M. Atwater, Jr. E. E. Boon Joseph E. Aue Gail Borden A. M. Austin R. S. Botsford W. S. Ayres John M. Boutwell

Jan 4, 1919

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By K. J. K. Weglo, M. U. Savich

"At the Falconbridge Limited, Canadian Nickel Division, Sudbury Operations, we investigated the ""NO NOISE"" ear muffs model NN3-F which is a Swedish product with foam-filled sealing rings (the Hellberg Standard Volume Hearing Protector). It is used extensively at Falconbridge mines in Sudbury.The research which was carried out in the four Falconbridge mines was conducted under three different headings: manufacturer's attenuation data (psychophysical method), clamping force and head size (bizygomatic diameter), and attenuation tests (physical methods) under working conditions.Manufacturers of hearing protectors claim their products offer noise reductions of 23 decibels (NRR) or more, but they fail to point out that this reduction is obtainable only under ideal conditions. The reality of attenuation under working conditions, as several studies have found, is quite different.Methods for using short measurements to determine the noise exposure index, and for controlling muff-wearing habits, were developed at the Elliot Lake Laboratory. Measurements taken at Falconbridge on ""NO NOISE"" ear muffs revealed that they have a practical attenuation of some IO to 13 decibels. It is important to note here that measurements also revealed that clamping force (thus attenuation) was in an inverse relationship with ear muff comfort. Measuring attenuation using noise dosimeters was a difficult job. Not a single surveyor would accept these measurements (physical method) for absolute accuracy. Apart from that, it was impossible to measure, in one shift, more than two work stations. Because of this, we sought a solution: measuring head size and clamping force in relation to actual attenuations.A detailed analysis of the relationship between attenuation and head size/clamping force was done at four mines. Standard deviation ellipses (standard error ellipses) for head size versus clamping force are in close agreement with measurements that were carried out. In order to measure clamping force an apparatus was constructed and a method for measuring suspension system durability is described in Appendices Band C of this report. At the same time we sought to reduce deterioration of ear muffs in mines as well as to put in place a system whereby attenuation can be controlled and improved. The clamping force apparatus can be operated automatically. The proposed control system is quick, simple and efficient . This system is equally applicable in small and large mining operations, and it can be totally automated and the data computerized for audit of the results. This control system is a new step in controlling ear muff attenuation in working environments.From these measurements of NN3-F ""NO NOISE"" muffs it can be concluded that ear muffs are not the total solution to protect the worker from noise.As the results were evaluated folio wing measurement, Falconbridge switched from the NN3-F ""NO NOISE"" muffs to approximately 90% Mark V ""NO NOISE"" muffs and 10% Mark V MSA muffs. These new muffs showed much better head size versus clamping force relationship and can be expected to produce 14 dBA or better attenuation of noise. RESUMEUne étude des casques antibruit ""NO NOISE"" modèle NN3-F, de fabrication suédoise, avec anneaux d'étanchéité en mousse (dispositif de protection contre le bruit ""Hellberg "" pour volume ordinaire)a été effectuée Ii la Falconbridge Ltd. , Division canadienne du nickel aux installations de Sudbury . Ces casques sont largement utilisés dans les mines de la Falconbridge Ii Sudbury.Cette étude aeu lieuen milieu de travail dans les quatre mines de la Falconbridge sous trois rubriques différentes soit: les données d'atténuation du bruit du fabricant (méthode psychophysique), la force de serrage et la taille de la tète (diamètre bizygomatique), et les essais d’atténuation de bruit (méthodes physiques). Les fabricants de dispositifs de protection contre le bruit prétendent que leurs produits offrent une réduction du bruit s'élevant Ii"

Jan 1, 1986

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By Greg Mclellan, Mark Johnson, John Pepper

In this paper, the measured vibrations are plotted in terms of the individual PPV components versus Scaled Distance (SD) on logarithmic scales. The maximum PPV is pIotted on a separate graph and equations are presented to predict the maximum PPV based on sealed distance and prediction level usmg power fits. The prediction levels include a 99.9% curve, which encompasses the data points and provides an envelope formula for determining the maximum PPV at South Florida sites. The dominant frequency distribution is established for the PPV components.

Jan 1, 2001

By James L. Hendrix, David Castillo

Cyanidation is one of the most common practices used in the extraction of gold and silver. One method of application is heap or dump leaching which entails the leaching of the gold or silver ore by spraying or dripping a cyanide lixiviant over the ore and collecting the effluent. The ore is placed on what is known as a leach pad system. A typical leach pad system consists of a foundation, a leakaqe detection system, a liner, and a cover layer (Strachan and van Zyl, 1988). There are many types of liners available for use. The type of liner depends upon what type leaching pad system us used. Generally, leaching pad systems can be categorized into two types: an expandable pad and a reusable pad. An expandable pad exposes the liner to the elements only in the initial stages of ore placement on the leach pad system. A reusable pad exposes the liner to the elements on a periodic basis. In addition to the exposure to the elements, the liner is also under the stress of the ore placed on it and the stress of the vehicular traffic across it. These stresses and exposure to the elements are the major causes of liner failures, which can appear as punctures, tears, cracks, and deterioration. Because of the possibility of the failure of the pads to contain cyanide-laden solutions the designs for liners of pads and ponds have become more and more stringent. Currently, though, there is some recognition that in some locales such stringent design criteria may not be required (Chatwin, 1989). Some soils have significant cyanide attenuation and degradation capacity. It has been found that soils containing carbon- aceous materia1 wi11 remove cyanide from solutions percolating through them (Chatwin, 1989). Of course metallurgists have long recognized the deleterious effect of carbonaceous material in the mill circuit. Sheridan, et a1 (1988) have shown that WAD cyanide is detected in the effluent of a 2 m column filled with ground carbonaceous ore only after it had been continuously washed with greater than 9 pore volumes of NaCN solution. It was decided to examine the potential of successfully attenuating cyanide by placing an organic material layer between a 1iner and the prepared soil base. One consideration for the selection of the organic material was cost. Sawmill wastes, ground agricultural wastes (such as corn cobs), and other organic wastes were considered. But the first waste to be tested was a product found at any metropolitan area, sewage sludge.

Jan 1, 1990