Search Documents

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

By Patrick R. Taylor

Glass is used for immobilization of radioactive and hazardous wastes due to its durability and ability to accept a variety of waste constituents into its network structure. Alternative high temperature vitrification techniques have the advantage of increased throughput, increased waste loading and being applicable to variable and heterogeneous waste streams. However, the increased processing temperature places further concerns on the increased volatilization of contaminants, and increased corrosion and erosion of me Iter components. A database of melt properties at higher temperatures, such as partitioning, viscosity, density and electrical conductivity, in the temperature range of 1400-20000 K are being developed.

Jan 1, 2000

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Rashmi Kumar, Amit Chatterjee, Sanjay Chandra

The practice of adding alloying materials to a molten bath is an integral feature of many pyrometallurgical operations. However, very little is known about the dissolution rate and solution mechanisms of solid additives in liquid melts. In foundries where large tonnages of liquid metals are handled, there is considerable interest in achieving optimum metal quality at minimum cost. This objective is influenced by several factors and the solution is often plant specific. Though the amount, sequence and mode of ferroalloy addition vary from plant to plant, various fundamental factors determine how quickly these additions dissolve in the bath. At the Ingot Mould Foundry (IMF) in TATA STEEL blast furnace hot metal is used to cast ingot moulds. The composition of hot metal desired for making ingot moulds demands addition of 20 kg each of Ferromanganese and Ferrosilicon in the 12 T transfer ladles into which the blast furnace metal is poured at the IMF. Owing to low temperature of hot metal at the IMF, casting commences immediately and complete dissolution of the ferroalloys is often not possible. To study this aspect in detail and to evolve suitable corrective measures, a mathematical model for the melting of a solid particle in a liquid metal bath was developed at TATA STEEL. The model was validated using the data available in literature. In keeping with published work, two separate dissolution periods were identified - a "shell period" and a "free dissolution period". The maximum thickness of the crust formed around a spherical particle shortly after immersion, can be obtained by using the mathematical model which has been developed. The model can also be used to investigate the effect of various parameters such as superheat of the bath, size of the particle, etc., on the maximum crust thickness and the particle melting time. On the basis of this study, the addition of ferromanganese and ferrosilicon was optimized at the IMF in Tata Steel.

Jan 1, 1996

By Eva B. Kisvarsanyi

An Early Proterozoic orogenic terrane of metasedimentary and metaigneous rocks underlies Nebraska, Kansas, and Missouri. Middle Proterozoic epizonal terranes of anorogenic granite and rhyolite, a known metallogenic province partly exposed in southeastern Missouri, overlap the orogenic terrane on the south. These Proterozoic terranes, covered by less than 1,000 meters of Phanerozoic strata, contain a virtually untapped source of mineral wealth and are one of the last frontiers for geologic exploration in the continen-tal United States. Petrographic study of subsurface samples is a powerful tool in the identification of favorable host rocks for a variety of ore deposits.

Jan 1, 1987

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976

By John R. Goode

The fist part of this paper comprises a general discussion on refractory gold ores and their mineralogy. Processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Jason H. Nadler, Jason A. Kulpe, Stephanie J. Lin

"A numerical method has been developed to predict the microstructural characteristics of reticulated metal foam. The porosity of this foam is derived from sacrificial template particles of known particle size distribution, which are incorporated with other precursor components. In this approach, a porous structure is numerically generated starting with Powell's sphere packing algorithm. The resulting stochastic structure has characteristics similar to those of corresponding metal foam. Deterministic inter-sphere connections are calculated to more accurately model the pore morphology that evolves during thermochemical synthesis. Estimations of pore morphology and specific surface area of the simulated material are compared to lab-synthesized materials composed of equivalent constituent compositions. In addition, the effect of template particle size, inter-sphere connections, and the geometric constraints on pore morphology and permeability are investigated to refine microstructural evolution and design.IntroductionReticulated foams, characterized by their interconnected pore network, can be obtained by incorporating spherical sacrificial template particles into precursor materials followed by template removal processes. The resulting structure is composed of contiguous spherical pores whose morphologies reflect those of the original templates. Based on some of the unique features of this synthesis approach, a methodology is introduced in this work whereby these foams are digitally constructed using experimental data from the template particle sizes and precursor formulation. Digitally constructed porous structures can then be compared to their laboratory synthesized counterparts through the quantification of structural features such as porosity and surface area per unit volume, which in tum are used to inform the foam's fluid transport propertiesThe spherical template particle packing algorithm developed here is adopted from Powell's work [1], which also includes approaches to obtain percolation and density in random packings [2]. Gervois gives a mathematical development for the stereological sectioning of packed hard spheres [3]. Stereological sectioning facilitates determination of relevant three dimensional morphological properties from two-dimensional data [4]. Studies on the sphere distribution size and the related particle packing density and coordination number results are studied in [5, 6]. Lastly, Kato describes a sintered neck structure, which is used with these packings [7]. This neck structure, as a model of the particle shape following heat treatment, is implemented here in a similar manner. A strong difference between the available literature and the methodology here is that spheres are packed to ultimately represent porous space, not rigid solid space."

Jan 1, 2011

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004

By Michael J. McGuire

Rostoker, Inc. has developed a process to smelt solid hazardous/non-hazardous inorganic wastes. Near seven hundred experiments were performed. Actual industrial wastes as well as reagent grade chemicals were used. By mixing a multiplicity of these wastes to proper formulations, then furnacing them, it was determined that saleable end products could be reclaimed; metal, fume and slag. The slag, due to its siliceous structure was tested to be leach resistant (40 CFR). This formed the essence of our patent, #5,180,421 "Method and Apparatus for Recovering Useful Products from Waste Streams". What is unique is that a HTMR (High Temperature Metal Recovery) process has been developed that can treat a multiplicity of wastes within the same furnace. The discussion will include a list of waste streams we have treated, details of proper waste formulation and experimental results.

Jan 1, 1994

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang

"Manganese is mainly consumed by steel and battery industries. In recent years, it is essential to utilize the low-grade manganese oxide ores with total manganese grade below 25%, as the high quality manganese ore resources are becoming scarce with the rapid development of the steel industry. Conventional pyro-metallurgical processes for utilizing manganese oxide ores are characterized by high production cost and energy consumption, low productivity, serious environmental pollution, etc. In this study, reduction thermodynamic of MnO2 reduced by sulfur was firstly carried out. Then, a novel process of reduction roasting with sulfur followed by acid leaching was developed to recover manganese from the very low-grade manganese oxide ores. Effects of main factors, including temperature, reduction time and S/Mn mole ratio, were investigated, and a high leaching efficiency of Mn above 95% was obtained under optimal conditions.IntroductionHigh/middle-grade manganese oxide ores are generally used in the metallurgical industries, particularly in steel plants and ferro-alloy units. The consumption of metal manganese in the ferro-alloy industry accounts for 85- 90% of the total Mn demanded [1]. Therefore, high quality manganese ore resources are becoming scarce with the rapid development of steel industry. It is essential to make good use of large quantity of low-grade manganese ores (TMn < 25%) presently available."

Jan 1, 2012

By Shu Bin, Lin Chen, Tian-zu Yang, Wei-feng Liu, Wan-da Bin

"Antimony resources are rich in china, its reserves and productions are ranking the first in the world. The Chinese antimony mineral resources are mainly existed in the form of three types, such as stibnite, antimony-gold ores andjamesonite. The antimonial dust that produced from lead smelting process is an important secondary antimony resource. The different process that was adopted to extract antimony depends on the different raw materials. The process of blast furnace volatilization smelting is mainly used to treat stibnite and antimony-gold ores. But jamesonite is treated by the process of roasting-sintering-blast furnace smelting. And antimonial dust is treated in the reverberatory furnace. Many new technologies that are applied in these traditional antimony smelting processes play important roles, such as deleading agent, antimony white production, air-oxidation method, direct-blowing method, bath smelting technology, and so on. At the same time, the development of antimony smelting technology in china is prospected according to the requirement of the state environmental protection.IntroductionThere are five countries that produce antimony in the world, such as china, Tajikistan, Bolivia, Russia, and South africa, but China is the largest country of antimony production in the world. In the world, the antimony productions of 2008, 2009, and 2010 are 182,000 tons, 154,000 tons, and 167.000 tons respectively, but Chinese antimony productions are 166.000 tons, 140,000 tons, and 150,000 tons respectively. So Chinese antimony production was accounted for more than 89% of the world in 2010. It indicates that China have irreplaceable advantages in antimony resource and production all over the world."

Jan 1, 2013

By R. W. Bartlett

The extensive central Idaho black sand placer deposits are a potential source of rare earth elements, particularly the heavy rare earth elements that are not prevalent in commercial bastnasite deposits. These placers derive from the Idaho batholith. The geology, occurrence, and extent of these deposits are reviewed and the diverse mineral assemblages and complex mineral chemical compositions of these sands are described. Niobium, yttrium and thorium are also present in significant concentrations. The results of prior mining practice, including concentration and separation of the heavy minerals are reviewed. Technical approaches to extraction of rare earths from Idaho black sand concentrates are discussed.

Jan 1, 1992

By Chao Li, Shuai Wang, Hongxu Li, Lifeng Zhang, Xie Yang

The method of chloride-hypochlorite leaching has the advantages of short process, low pollution and higher in reaction rate compared with the traditional leaching method. In this research, NaCl - NaClO solution is used to leaching gold from a refractory gold concentrate, and the influence of NaCl and NaClO concentration, reaction time to the leaching rate were investigated in this experiment. The raw materials and the leaching residue were characterized by a series of analysis methods such as XRD, XRF, SEM and EDS. Results indicate that the leaching rate and the desulfurization rate can be achieved at 96.26% and 98% with most optimum conditions as follows: NaCl concentration 50g/L, NaClO concentration 200g/L, Liquid-solid ratio 10:1, the best reaction time was 150 mins. And these conditions should be guaranteed pH<8.0, ORP>900mV.

Jan 1, 2015