Search Documents

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By F. J. Arriagada

Where gold is present in a finely disseminated form within sulfide particles, the porosity and surface area of the calcined material strongly influence leaching since they control the penetration of solution inside the gold-bearing grains. On the basis of a stability diagram for the Fe-O-S in the temperature range of 400 to 750aC, the expected sequence chemical transformations associated with the oxidation of pyrite is discus-sed. By using analytical techniques which include scanning electron microscopy, X-ray diffraction and BET gas adsorption, the chemical and structural changes experienced by auriferous pyrite-arsenopyrite concentrates and pure pyrite samples are studied under an oxidizing roasting atmosphere of com-position 80% N + 20% O2 in the temperature range of 450 to 750°C. The results indicate that as the roasting temperature increases, the surface area of the calcines decreases sharply after a maximum value attained at about 450-500°C. SEM micrographs show that the needle-shaped tips which characterize the surface of the oxide product become wider and the size of the pores between them is decreased when the roasting temperature is in-creased from 550 to 750°C. This effect suggests that the formation of a more "closed" hematite product at higher temperatures is due to sintering associated with a faster growth and crystallization of the oxide. A strong correlation is shown between increasing roasting temperature and increase in gold lost in cyanidation tailings, an effect which may be partly attributed to the loss in surface area of the calcines.

Jan 1, 1982

By Hiroaki Kawamura, Takeshi Yoshikawa, Kazuki Morita, Yutaka Yanaba

"To develop an alternative metallurgical process for phosphorus removal in the production of solar-grade silicon (SOG-Si), slag treatment of metallurgical-grade silicon (MG-Si) was conducted, followed by acid leaching. Phosphorus-doped silicon alloy or MG-Si containing certain amounts of phosphorus and calcium was reacted at 1723 K and 1773 K with CaO--CaF2 of several compositions. Phosphorus removal from the molten silicon into the slag phase was confirmed by reduction to phosphide ions, P3-, and phosphate ions, P3-. These ions were separately determined using a wet chemical analysis method developed by ourselves. The highest phosphorus distribution ratio obtained was 2. 7 after reaction for 18 h with 17.5 mass% CaO--CaF2 slag. We then conducted acid leaching of the silicon and achieved removal of a large fraction (over 90 % ) of the phosphorus, which was much higher than that obtained by ordinary oxidizing slag treatment.IntroductionIn recent years, the production of solar cells has been increasing rapidly. Because of this, the demand for solar-grade silicon (SOG-Si) has also been growing rapidly. The development of lower-cost mass production processes is therefore needed to provide silicon feedstock. Phosphorus is one of the impurities in metallurgical-grade silicon (MG-Si). Because of its large segregation coefficient (kp = 0.35) [l ], it is difficult to remove phosphorus using a solidification refining process. Vacuum melting is considered to be a promising method for removing phosphorous from MG-Si [2], but the issues of high cost and large energy consumption have still to be resolved.Slag treatment is often used to remove impurity elements by oxidizing reactions during general oxidation refining processes. For example, phosphorus in molten steel is removed into a slag phase as phosphate ions, PO4 3-l-, by the following reaction:"

Jan 1, 2013

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Rafael Padilla

In the production of copper from chalcopyrite (CuFeS2) concentrates by the smelting and converting technology, the ambient pollution with gaseous S02 and toxic metals such as arsenic compounds is still a serious problem, especial1y in the converting step due to the batch nature of the conventional Peirce Smith process. Non-SO2 emitting alternatives are leaching processes. However, few of them have had a limited industrial application and they are not very effective in discarding safely the toxic impurities. A combination of pyro-hydrometal1urgical methods: the sulfidation of chalcopyrite and subsequent leaching of the sulfidized material is a non-polluting alternative to treat not only clean chalcopyrite concentrates but also complex chalcopyrite-enargite concentrates. In this article, this alternative is discussed concerning the thermodynamics and kinetics of the sulfidation of chalcopyrite with gaseous sulfur. The kinetics of the leaching of the sulfidized concentrate in an H2SO4-NaCI-O2 system is also discussed.

Jan 1, 2003

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By Leijun Li, M. M. Mahapatra

"A three-dimensional finite element model with moving heat source was developed for pulsed-laser powder deposition (PLPD) process. Experiments were conducted to study the repair of superalloy components using the PLPD process. During the experiments, IN 625 powder was deposited on a superalloy substrate similar to IN 738. The process was modeled using three-dimensional finite element analysis. Element birth and death technique was used in the finite element model for simulating the deposition of powder layer on the substrate. A moving distributed heat source was used in the thermal model for realistic simulation of the process. Temperature dependent thermal material properties including enthalpy were used for the powder and the substrate in the transient thermal analyses. The fusion zones and peak temperature distributions of the deposits were predicted from the transient thermal analyses.IntroductionPoor weldability is a critical issue of superalloy repairing. The microstructural directionality of the superalloy components are disrupted when repaired by the fusion welding processes. Currently there is no widely accepted method to economically and reliably repair directionally solidified superalloys components. Pulsed laser powder deposition process (PLPD) is a promising repairing technique as the substrate is not severely affected by the heat source.In this study PLPD technology is used as the tool for superalloy repairing. In most of the land based turbine engines the directionally solidified nickel based superalloy similar to IN 738 [1] is used as the bucket material. The turbine engine blade tips are subjected to a combination of extreme operating conditions and corrosive environment. The tip of the nickel based turbine engine blades can be repaired using IN 625 material as suggested in the literature [1-2]. IN 625 is considered to be ductile and strong enough for the purpose of Ni based turbine engine blade tip repair[1-2]. During the present PLPD investigation, IN 625 powder was used as the deposit material on an experimental super alloy substrate similar to IN 738 superalloy used as the cast superalloy for the turbine engine blades."

Jan 1, 2012

By Daniel Kittelty

A fully instrumented laboratory electrowinning cell has been used to produce nickel cathodes from synthetic solutions containing various impurities in order to evaluate the effects of both metallic ions and organic reagents (from prior solvent extraction and other processes) on the quality of the electrodeposited nickel. The conditions used were typical of those employed in industrial electrowinning operations. The impurities were found to alter the crystal size and shape, induce the development of hydrogen pits on the deposit surface, incorporate as metal hydroxide crystals in the deposit, and alter the internal stress and current efficiency. These effects have been interpreted in terms of previously established relationships between the solution composition and the physical properties of the cathodes. The incorporation of the common metal impurity ions into the deposit have been interpreted in terms of a mass transport controlled reduction or precipitation reactions. In particular, a low concentration of aluminium ions resulted in an initial highly deleterious effect, which was replaced by a positive influence at higher concentrations. A model which involves the buffering effect of the aluminium on the pH at the cathode surface has been proposed.

Jan 1, 2003

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Wenbo Luo, Kang Liu, Fusheng Mao, Jilai Xue, Jun Zhu, Chunlei Yang

Extracting alumina from coal fly ash (CFA) is of great interest for both environmental protection and recycling valuable alumina content. In this study, ultrasonic aided leaching process as an effective method was investigated to enhance extracting Al2O3 from CFA via concentrated sulfuric acid sintering. The influence of ultrasonic power and processing time were tested under the conditions as the same as those without ultrasound. It is found that the alumina extraction rate can reach 90.5 % with ultrasound assistance, while the ultrasonic treatment can reduce almost 15 ~ 30 min in leaching time and 5 ~ 10 oC in leaching temperature than those without ultrasonic operation at the same Al2O3 extraction rate. In addition, the ultrasonic can reduce calcium content by 6 ~ 8 % dissolved into the leaching liquid. SEM analysis also shows that the residue particle size with ultrasound is smaller than that without ultrasonic treatment.

Jan 1, 2015

By Wenbo Luo, Jilai Xue, Tiepeng Li, Jun Zhu

Sodium silicate solutions for producing silica have been ultrasound treated to enhance the precipitation process in laboratory scale. Higher precipitation rate was found with ultrasound treated solutions than those without ultrasound. The obtained SiO2 powder products were characterized using XRD, SEM, BET and laser particle size analyzer. The particle size distribution and the specific surface area of the powder products varied with the power input level and the processing time of the ultrasonic treatment. The results indicate that the efficiency of the precipitation process can be improved optimally when the ultrasound is conducted into the solutions before the nucleation stage.

Jan 1, 2015

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By Hideyuki Itou

Municipal wastes are mainly incinerated in Japan. Both bottom ash and fly ash from the incineration treatment are smelted recently to decrease the volume. Direct smelting of municipal wastes is also becoming popular. The smelting treatment generates fly ash which contains concentrated heavy metals such as Zn, Pb and Cu, and the harmfulness is causing concern. The smelter fly ash is mainly landfilled after stabilization. An effective treatment process of the smelter fly ash is required to recover the metals. For the treatment process, an application of chloridizing volatilization technique is considered. Chloridizing volatilization experiments were carried out to determine the effects of various factors on the volatilization behaviors in this study. A pretreated ash was mixed with a main raw material which mainly consists of hematite. Calcium chloride water solution was added into the mixture. The mixture was pelletized, dried and used as samples for the volatilization experiments. The sample was placed in the reaction tube heated in an electric resistance furnace. 5%02-95%N2 gas with controlled humidity was introduced into the reaction tube. Effects of humidity in the carrier gas, addition of calcium chloride and mixed ratio of the ash to the main raw material were investigated on the volatilization of Zn, Cu and Pb. To determine the volatilization behavior, samples were taken from the furnace at specified temperatures on the heating stage. In addition, experiments at specified holding temperatures for 15 minutes with shortened heating time were conducted. The two series of experiments revealed the effect of heating temperature on the volatilization behavior of Zn, Cu, Pb and Cl.

Jan 1, 2006

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

By G. Springer

The identification of lost mineral values in mill tailings frequently requires the inspection of hundreds of thousands to millions of particles. The search of these particles can be made automatic by using an electron microprobe. A standard instrument (Cambridge Mark V) was modified by the addition of stepping motors to advance the specimen stage in a controlled manner. The X-ray Signal is monitored continuously by a computer interfaced to the instrument with an analog-to-digital converter. 400,000 particles of a tailings sample can be scanned in about 3 hours. Particles as small as 2 um and containing as little as 3% of a particular element can be detected.

Jan 1, 1982