Search Documents

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By William M. Gleason

When SME’s 2006 Arizona Conference convened in December at the Hilton El Conquistador Resort in Tucson, AZ, there was considerable excitement among the 387 attendees. There was a noticeable buzz surrounding the progress of Phelps Dodge’s Safford copper mine in southern Arizona, one of the first new major copper mines to be permitted in more than 30 years in the United States. There were also plenty of good feelings about the mining industry in general. Commodity prices remained high and with no signs of a slowdown in the immediate future. Things were good in Arizona. But there were also cautionary tones at the conference and the Mining Foundation of the Southwest banquet that preceded it.

Jan 1, 2007

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By S. Shi, J. Y. Hwang, B. Li

Silver, copper, and zinc are commonly known elements with antibacterial and antifungal capabilities. Attempts have been made to dope silver on minerals, glass, and ceramics and the resulting materials have been investigated for their antibacterial and antifungal properties. Since silver is expensive and very reactive, silver doped materials have been found inappropriate in some applications. Copper-vermiculite is investigated as an alternative. Vermiculite has high cation exchange capacity on the magnesium ion in the crystal structure. Copper ion may have a high tendency to replace magnesium because of similar charge interference and ionic radius. Copper-vermiculite is prepared by reacting vermiculite and copper chloride solution. By impregnating copper ions into the nanometer openings between the layers of vermiculite, it is possible to render the composite with antibacterial functions if the copper ions could be released gradually from the composite. The antibacterial efficiency of Cu-vermiculite against Escherichia coli was studied using the Halo method. The results show that Cu-vermiculite is effective for preventing the reproduction of the bacteria. Heat treatment of Cu-vermiculite at up to 400°C does not show significant changes in antibacterial activities.

Jan 1, 2002

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By Leslie F. Ruppert

The US Geological Survey (USGS) is currently conducting a coal resource assessment of the coalbeds and zones that are projected to provide the bulk of the nation’s resources for the next few decades. The Pittsburgh and Upper Freeport coals are the first two beds in the northern and central Appalachian basin region to undergo fully digital coal assessments. The bed-specific assessments are being carried out in partnership with the state geologic surveys of West Virginia, Ohio, Pennsylvania and Maryland. Comprehensive stratigraphic and geochemical databases have been developed for both of the beds. The extent of the bed with mined areas, structure contour, isopach, and overburden thickness maps for the Pittsburgh coal bed have been released as USGS open-file reports.

Jan 1, 1999

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By Michael Rehbock-Sander

The Gotthard Base Tunnel (GBT) is 57 km (35 miles) long and consists of two par-allel single-track tubes with an ex-cavation diameter ranging from 8.8 to 9.5 m (28.8 to 31.2 ft). These are interlinked by cross-passages every 312 m (1,000 ft). Two multifunction stations (MFS) are located in the sections Sedrun and Faido, at one-third and two-thirds of the entire tunnel length (Fig. 1). These will be used for the diversion of trains to the other main tube via tunnel crossovers, for the housing of tech-nical infrastructure and equipment and for potential emergency stops. To reduce construction time, the GBT was divided into five sections and was excavated from several sites simultaneously. The tunnel was excavated from the two portals, Erstfeld in the north and Bodio in the south, and also from three intermediate attacks, with their corresponding access tunnels, in Amsteg and Faido and two vertical 800-m (2,624-ft) deep shafts in Sedrun.

Jan 1, 2012

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014