Search Documents

By M. J. King, A. Weissenberger, W. G. Davenport

Keywords: Pyrometallurgy, sulphuric acid, sulphur dioxide The raw material for sulphuric acid manufacture is clean SO2 gas. It comes from (i) burning molten by-product sulphur; (ii) roasting or smelting metal sulphide concentrates, and (iii) decomposing contaminated organic chemical process sulphuric acid catalyst. Efficient gas cleaning is required for metallurgical and contaminated acid decomposition gases, especially the former. Sulphuric acid is made from SO2 gas by (i) oxidizing the SO2(g) to SO3(g) in contact with supported liquid-phase catalyst then (ii) reacting the resulting SO3(g) with the water component of 98.5 mass% H2SO4, 1.5 mass% H2O acid. This paper discusses the reasons for these process steps and indicates how acidmaking can be controlled and optimized. Special emphasis is placed on SO2(g) oxidation efficiency and how it is influenced by feed gas composition, feed gas temperature, catalyst composition, catalyst bed pressure, number of catalyst beds, and double versus single contact acidmaking. In addition, a review of various other treatment methods for SO2-bearing gases is provided. A brief description of each process is included along with commentary on their technical and economic applicability for use at metallurgical facilities.

Jan 1, 2006

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By T. J. Goff

Keywords: accurate control, matte level, smelting operations, process control, tapping, sounding bar, electromagnetic measurement [ ] Accurate control of matte levels during primary matte smelting operations is desirable in order to improve process decision-making. High matte levels in the vessel could have to disastrous consequences, particularly in the new generation of intensive smelting furnace with deep-cooled copper coolers. Knowing when to commence tapping and a better understanding of melt times can only be improved if the furnace levels are monitored correctly. At Lonmin Marikana Smelter Division it has long been understood that the matte level information being provided by the manual sounding bar is only as good as the operators? following of measurement procedure, their skill in assessing what the sounding bar is displaying, and their individual interpretation of what they are looking at. This paper sets out to show how this problem was identified as an area of major concern to the plant, how a solution was sought and how an electromagnetic measurement system was installed as an alternative measurement to the matte sounding bar system. Other areas discussed in the paper are the difficulties to be overcome when first installing new equipment and how these teething problems were solved by close co-operation between Lonmin and equipment suppliers, which led to some design modifications to the delivery system. In conclusion the paper discusses the results between the electromagnetic measurement and the manual sounding measurement and how best to integrate the generated data into the plant?s process control system for improved decision making.

Jan 1, 2011

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By G. V. R. Landman

It is self-evident that economic pressure demands that today?s mines stay ahead and stay competitive. The challenge, however, isto find fresh approaches to the pursuit of efficiency and operational effectiveness. Rather than focusing on individual activities in isolation, a process that can lead to poor investment decisions affecting other critical areas of operation, a key concept is optimization of the whole value-adding process of mining. This concept is often called ?mine to mill?. Whereas it is never easy to establish optimal conditions across a whole mining operation, the quality and consistency of the blasted rock strongly affects all operations. In many instances an inability to control rock breaking has been unchallenged, leading to significant investment in time and money to manage the consequences of poor and/or inconsistent rock breaking. This paper discusses how electronic initiation systems can play a major role in optimizing the whole mining operation. Electronically programmed detonators provide not only the ability to tightly control a key parameter, namely timing, but also the opportunity to extract blast data for a continuous improvement process. The ability to alter predictably, using feedback from the downstream processes, blasting variables such as fragmentation, throw, wall stability, and vibration, is a huge advantage. The current understanding of the effect of timing, accuracy, and scatter on rock fragmentation is reviewed and offers reasons why there is significant progress in controlling blast results. Two case studies are examined, which demonstrate the benefits of the technology on the economics of the operations under review.

Jan 1, 2010

By D. G. Krige

Using chip sample data and spatial structure parameters from a large mined-out section of a South African gold mine the advantages to be gained from a regular underground borehole drilling programme have been investigated for short- and medium- to long-term planning based on block valuations. The results have been compared with the current position, which relies invariably on the extrapolation of limited peripheral sampling data from raises, gullies or stope faces. Some preliminary work has also been done regarding the implications of such underground drilling on costs used for the present pay limit calculations. The results of the study, though preliminary, show that the net advantage of advance regular underground drilling could be substantial and that a more intensive follow-up research is warranted.

Jan 1, 2003

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

[ ]

Jan 1, 2009

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By M. H. Solomon

After the global financial crisis of 2008, African mining is entering anew phase of development. The rapid withdrawal of emerging market funding from the critical exploration and development industries provided a hiatus in funding, a gap which was quickly filled by Chinese and other Asian investors. While the continent is still economically dependent on its extractive industries, the prevalence of Dutch Disease has undermined Africa?s ability to benefit fully from its mining, oil, and gas industries. While the extractive industries are closely related to many of the more fragile and failed states in Africa, it is equally true that the strongest states in Africa have mining-based economies. This paper explores the possible linkages between mining, strong and weak political economies, and poverty in Africa. It draws the conclusion that neither Dutch Disease nor Resource Course is a given in resource-endowed countries, and that it can be avoided if the mining economies in these countries are actively integrated into their respective broader economies and used to foster economic diversification. The author asserts that given the capacity constraints of many African governments, it is contingent on mining companies to become integrally involved in catalysing diversification around their infrastructure and supply chains.

Jan 1, 2011