Search Documents

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

By Michael D. Justason

...a global perspective... In March of 2000, the Japanese Geotechnical Society added "Rapid Load Testing" to their national standard for pile testing. In the year 2000. it is estimated that there will be more than 500 "Rapid Load Tests" on foundations around the world. ...so what is a "Rapid Load Test", and why is it gaining acceptance and popularity?

Jan 1, 2001

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By Hui Yongning

This paper presents a simulating test of constitutive relation of soil anchor in laboratory and puts forward a new plastoelastic mechanical model, on which a new calculating formula of elastic and plastic limit bearing capacity for soil anchor is suggested and two engineering projects verify that this method is adaptable.

Jan 1, 1991

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By Inn-Joon Park

Major problems associated predicting soil-structure interaction behavior are based on the fact that soil is neither homogeneous nor elastic and soil properties are spatially variable. There also exist significant coupling problems between the behavior of the structure and geologic media. When designing foundation or other geotechnical structures, the load transfer between the soil and structure takes place at the contact surface. This surface is called the interface. The behaviors of interface play an important role in the load-deformation response of soil-structure interaction systems. The purpose of this study is to develop improved model for simulation of saturated sand-steel pile interface behavior based on a general concept, called the disturbed state concept (DSC), which can characterize the behavior of saturated soils under dynamic loads. In this study, the Disturbed State Concept (DSC) constitutive model is calibrated and modified for steel pile-saturated sand interface and interaction by using the continuous hardening model for relative intact (Rl) state and the critical state model for the fully adjusted (FA) part in the saturated sand material. The general formulation for implementation has been developed. Then, the DSC model with modification for interface and saturated sand is implemented in finite element program based on the generalized Biot's theory. The interface tests under one-way monotonic and two-way cyclic loading and cyclic triaxial tests are executed for defining the parameters for interface and surrounding soils. Based on these parameters, steel pile-saturated sand interface and interaction are numerically simulated using the finite element program modified in this study. The DSC predictions show improved agreement with the observed results from laboratory test.

Jan 1, 2002

By Walter Ensinger

Working safely means working cost-effectively. Every "dangerous occurrence" and - even more so - every industrial accident causes disruptions in the planned course of construction. Besides moral and legal obligations, economic aspects are therefore also factors motivating increased efforts towards optimal prevention: improvements in work safety and protection of health are wise investments! Ever since its earliest days, the European Federation of Foundation Contractors (EFFC) has made this subject one of its key objectives and therefore set up a Safety + Environmental Working Group, in which experts from the member organisations exchange national experience and develop proposals for "best practices". The paper presents current developments and results from the work of the S+E WG with particular reference to the project "Ideas for Safety Improvement".

Jan 1, 2006

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

Jan 1, 1996