Search Documents

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By D. Hodouin

Jan 1, 1978

Overview ?G-9 Discovery Hole 420 drilled May 2005 ?14.16% Zn, 1.76% Cu ?Greenfield discovery built into the G-9 Mine in under 4 years. ?Utilized a unique ?Parallel Track? approach to fast-track mine development. ?Raised over $200million in financing without a Feasibility Study. ?Mine built for $149.7 million, only 20% over PEA. ?Commercial Production declared April 1, 2009. ?G-9 Mine has now completed the first year of commercial production on April 1, 2010. ?Initial cash costs per pound of zinc US$0.39/lb -US$0.45/lb range. ?Mill operating at over1,900 tpd in March 2010, well above design capacity (1,500tpd) only one year after starting commercial production. ?Balance Sheet -$167 million assets, $24 million long-term debt, $22 million cash. ?Restarted Exploration ?excellent initial results. ?Strategically positioning Farallon to grow to a mid-tier mining company.

May 1, 2010

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By Steve Custer, Tim Kahl, Sue Parker

"The primary objective of the Barrick Goldstrike expert system is to achieve the desired liberation size for the autoclave circuit while maximizing throughput. In addition, when downstream limitations (autoclave circuit or others) restrict the milling circuit tonnage the expert system further improves grinding product size. Since its implementation, the expert system has provided expected throughput improvements while improving or maintaining circuit performance.Barrick Goldstrike and MinnovEX Technologies Inc. teamed up to install an expert system to control Line I and I1 of the autoclave grinding circuits. The dissimilar equipments of the two grinding circuits coupled to different production objectives, skepticism among operators, and the variability of the ore types processed in each line challenged the implementation.To ensure implementation success, Barrick Goldstrike dedicated four administrators full time to the project. The system administrators included two metallurgists, a process control engineer and a mill trainer. As usual, the control room operators were the experts who provided the operational logic for the foundation of the control system. The administrators and all eleven of the control room operators signed off on acceptance of the system. Current online utilization is 95%.INTRODUCTIONThe grinding circuit for Barrick Goldstrike’s autoclave process consists of two SAG Mill Ball Mill lines. Line 1 grinding circuit is comprised of a 22 by 8 foot, 2500 horsepower Allis Chalmers (AC) variable speed SAG mill, followed by a 12.5 by 14 foot, 1250 horsepower AC ball mill, and a 13.5 by 18 foot, 1800 horsepower Dominion ball mill in parallel. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1352 Nordberg Omnicone crusher (4.5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The ball mill circuit is closed with 6 Krebs super D20 cyclones. Line 2 grinding circuit is comprised of a 24 by 12 foot 4000 horsepower Fuller variable speed SAG mill followed by a 16.5 by 30.5 foot 5000 horsepower Fuller ball mill. SAG mill recycle from the primary discharge screen (+5/16 inch) is processed through a 1560 Nordberg Omnicone crusher (5 foot). A secondary SAG discharge screen (+1/8 inch) closes the SAG circuit. The line 2 ball mill circuit is closed with 12 Krebs super D20 cyclones. The underground Meikle ore is typically fed through Line 1. Achieving the desired product size is critical for successful processing of Meikle ore. Open pit Betze ore is fed to Line 1 when Meikle ore is unavailable. Line 2 processes Betze ore exclusively. Throughput is maximized when processing Betze ore as the product size is less critical. The products of these two circuits are combined as feed to the autoclave circuit. The ore types and the autoclave circuit demands determine the required grinding circuit product size and maximum combined mill feed tonnage."

Jan 1, 2001

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

By Richard Peaker, Jens Lichter, Alexander V. Potapov

"The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism.This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.INTRODUCTIONThe great majority of newly installed cells in mineral processing plants world-wide are of the cylindrical tank design and this tank shape offers a number of hydraulic advantages over the older style of square cells. Cylindrical cells give symmetrical flow patterns and by careful design of the mechanism and tank internals, the flow patterns generated can concentrate the more intense mixing in the lower portion of the cell to promote good solids suspension and particlebubble contact. Simultaneously, cylindrical tank design gives a more quiescent upper zone for particle-bubble transport into the froth zone. These symmetrical flow patterns are naturally disturbed in normal operation by the slurry inflow and outflow from the individual cells. The challenge for flotation cell designers is to determine the magnitude of these flow disturbances, and to assess whether or when the inflow and outflow rates have a sufficient impact on the hydraulic flow patterns so as to potentially affect the metallurgical performance of the flotation cell."

Jan 1, 2007

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By L. Boyd, A. Charland, G. Potts, D. Fragomeni, N. O. Lotter

"The Raglan orebody and concentrator has been the subject of study in Process Mineralogy at Falconbridge since 1998. (Lotter and Tuzun, 1998) The orebody is classified into three distinct textural groups, or end members. These are referred to as disseminated, net-textured, and Massive Sulphides, and differ in terms of mineral grain size, nickel grade, hardness, and mineral association. In this paper, it will be shown that the sampling and characterisation of each end member on an individual basis develops a higher-level understanding of the processing requirements and behaviour of the mixture of ore as presented to the mill.The end members have been used in robust prediction of recovery at various grind size p80 from laboratory scale High Confidence Flotation Tests. Weighted mean mixtures of the end members have been mathematically combined to determine impact of textural distribution on metallurgical performance as a function of grind size.The ore end members also vary in hardness and breakage mechanism and have been used to model throughput capability for existing, optimized and retrofit grinding circuits. This modeling has provided a range of expected throughputs as the relative proportions of each end member varies.Finally, the differing grinding requirement per end member has led to the development of grinding and flotation strategy that increases rougher flotation recovery and provides flowsheet options for a concentrator expansion. This leads to further understanding of the plant performance as a function of ore mixture."

Jan 1, 2005

By A. Tylczak, C. Shook, A. Doogan-Smith, S. Loif, B. Hilscher, P. Nayak

"This paper discusses how to effectively conduct energy efficiency studies during the design of new mineral processing plants and plant expansions. Energy management studies for new plants are ideally conducted as part of the feasibility study, but can also be done at the detailed design stage prior to the purchasing of equipment. Energy management engineers work as part of the mineral processing plant design team.Such studies usually result in energy savings of approximately 3-8% of the predicted plant’s energy consumption and energy demand. Potential cost savings can be significant. A variety of mineral processing systems – crushing/grinding, pumping, materials handling, fans/blowers, compressed air, and others – are assessed within this study.Energy Management Information System (EMIS) studies can also be performed for the new plant or plant expansion, as an independent study. EMIS can be incorporated into the electrical and controls design of the plant.Most Canadian Utility companies fund new plant design studies and provide financial incentives based on the predicted energy savings and incremental cost of the more energy-efficient design. A new plant energy efficiency study improves the potential for energy reduction because only the incremental equipment cost is included in the project return-on-investment calculation. After the design and construction phases, energy efficiency projects must justify the entire cost of the upgrade, which is significantly higher than the incremental cost alone.This paper outlines the major steps of a new plant/plant expansion energy efficiency study, the available utility company incentives, and the areas yielding the largest potential energy savings.IntroductionThis paper discusses energy efficiency studies and energy management systems with regards to mining operations. Energy management refers to the systems of monitoring, analyzing, and optimizing energy usage within a facility. It includes energy efficiency optimization of the initial plant design as well as the implementation of an Energy Management System (EnMS) and Energy Management Information System (EMIS) for optimizing energy usage over the lifetime of the facility. An EnMS is the organizational framework and procedures for managing energy use; an EMIS is the system of monitoring, reporting, and tracking process energy use against targets."

Jan 1, 2016

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

By G. Lee, E. T. C. Spooner

"Molybdenum mineralization at Boss Mountain is hosted by the Triassic Takomkane quartz monzodiorite batholith and is associated with a Cretaceous monzogranite stock. Ore has been mined from a sheeted vein system that describes a partial annulus centred upon the apical region of the stock and from subvertical breccia pipes that emanate from the stock. Molybdenite precipitation is coincident with CO2 effervescence from a dilute (1.9 mole o/o NaC/ equivalent) hydrothermal fluid over a temperature range of 250°C to 370°C at a pressure of approximately 350 bars, interpreted to be greater than or equal to the lithostatic load and equivalent to a depth of 1.3 km or less.IntroductionThe chemical and thermal constraints on molybdenum transport and deposition to form molybdenum ore deposits are not well understood. To address this problem, the Boss Mountain mine in central British Columbia, operated by Noranda Mines Ltd., was chosen as a well-described (Soregaroli and Nelson, 1976), relatively small and simple example of a Cordilleran Mo~ deposit. It is situated on the northeast slope of Takornkane Mountain, 10 km west of the community of Hendrix Lake (N.T.S. 93A/2W; latitude 52°06'N, longtitude 120°56'W). Access is from 100 Mile House by nearly 90 km of road, the first 50 km of which are paved."

Jan 1, 1995

By Jarek Jakubec

The new euphoria in diamond exploration brings with it a need to understand the challenges that new projects can face in different stages of the development and risks that the commercial outcomes from the new projects fall short of expectations. In many cases, the problems are related to a poor understanding of the technical risks and a failure to adequately address them during the course of investigation. Failure to evaluate all disciplines to the same level of certainty could lead to a situation where the important issues are only identified late in the project development, resulting in costly delays and financial difficulties. The diamond projects located in Canadian Arctic, with its challenging environmental, geographical, social, political and geological contexts are especially sensitive to the high variability of the outcome. This presentation highlights some of the technical aspects that could be the leading sources of risk in diamond projects and could ultimately result in inappropriate mine designs, reducing the economic outcome.

May 1, 2006