Search Documents

By X. Cao, P. Wanjara, J. L. Fihey, X-T. Pham, F. Mirakhorli

Single-pass hybrid laser-arc welding of 10-mm thick cast plates of CA6NM, a low carbon martensitic stainless steel, was carried out in butt joint configuration using a continuous wave fiber laser at its maximum power of 5.2 kW over welding speeds ranging from 0.75 m/min to 1.2 m/min. The microstructures from the fusion zone to the heat affected zone and base metal were characterized after post-weld tempering at 600°C for 1 hour. From optical and scanning electron microscopy examination, the fusion zone was observed to mainly consist of tempered lath martensite and some residual delta-ferrite. The mechanical properties including microindentation hardness, ultimate tensile strength and Charpy impact energy were evaluated in the post-weld tempered condition and correlated to the microstructures and defects. The ultimate tensile strength and Charpy impact energy values of all the fully penetrated welds in the tempered condition were acceptable according to ASTM, ASME and industrial specifications. The failure mechanisms during tensile deformation and Charpy impact loading were examined by scanning electron microscopy, fractography and optical metallographic analysis near the fracture origin.

Jan 1, 2015

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By Martin Bergeron

Producteur d?or de taille intermédiaire Mines Aurizon Ltée Bureau-chef àVancouverMine et projets localisés au Québec2

May 1, 2011

By A. R. Miller, R. A. Stanton, M. J. Male, G. R. Cluff

"The Dubawnt Group consists of continental sedimentary and volcanic rocks which fill structural depressions - Baker Lake Basin, Yathkyed Lake and Angikuni Lake subbasins- whose evolution was controlled by late Aphebian extension, between 1.9-1.8 Ga. Structurally controlled uranium mineralization having the signature U + Mo + Ag + Pb + Cu ± Zn is spatially related to (i) intersecting fault systems that record multiple movements, (ii) chemically reactive lithologies containing sulphide, chlorite or graphite/ carbonaceous matter in the Archean and Aphebian basement complex and as alkaline volcanics of the overlying Dubawnt Group and (iii) areas containing thick successions of basal Dubawnt Group red clastic sediments.The most significant uranium occurrence found to date is the Lac Cinquante deposit, which contains 14 million pounds U3O8 of drill-indicated reserves. Mineralization is hosted in Archean meta-volcanic and metasedimentary rocks of the Henik Group adjacent to the basal Dubawnt unconformity in the northeastern A ngikuni Lake subbasin and occurs as plunging pods in and peripheral to a fractured and brecciated tuffaceous meta-sediment- sulphide+ carbonaceous exhalite. This deposit exhibits many features typified by the classical vein deposit at Beaverlodge, northern Saskatchewan.Epigenetic stratabound U + Cu + Ag ± Mo mineralization, typified by the 74-1E prospect in the eastern Baker Lake Basin, is hosted in thermally altered Kazan redbeds adjacent to alkaline dykes.At the eastern end of the Baker Lake Basin, small prospects having an elemental signature U + Se + Cu + Ag +Au are interpreted as unconformity-related mineralization associated with the Helikian The/on Basin.The Dubawnt Group rocks of the Baker Lake Basin, subbasins and adjacent basement complex contain uranium mineralization of two eras- Late Aphebian and Helikian."

Jan 1, 1986

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By J. Paturaud, A. G. Villemiane, J. Y. Buffiere, D. Fabregue, M. Perrier

In this work, a detailed characterization of the cyclic damage mechanisms on duty in car heat exchangers has been carried out in order to improve their reliability. The material which consists in very thin (<0.3 mm thick) sheets formed of 3 co-rolled aluminum alloys (4045 /3916/ 4045) has been brazed in order to obtain metallurgical and surface conditions representative of those of the real components. Fatigue tests at constant stress amplitude have been performed at room temperature and 120°C in order i) to characterize the cyclic resistance of the studied materials and ii) to study the effect of temperature on the fatigue damage mechanism. The mechanisms leading to failure have been identified from post mortem fractographic analysis. The Wohler curves obtained show that, contrary to common structural Al alloys, this type of thin sheet brazed multi material can be cycled for several hundred thousand cycles at very high stress level (> ~ 80 % of the tensile strength). This behaviour is analysed with respect to the microstructure resulting from the brazing process and the low number of grains present in the sample thickness (around 5 grains).

Jan 1, 2015

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By H. M. Lima, L. A. Gomiero, C. A. de Morais

ABSTRACT The Caetité-Brazil uranium facility produces approximately 400 tonnes U3O8 per year from an ore averaging 0.29% U3O8. The process steps are ore crushing, heap leaching with sulphuric acid, uranium separation and purification by solvent extraction (SX) with a tertiary amine, followed by stripping with a sodium chloride solution, precipitation as ammonium diuranate (ADU), and product drying. A change in the milling process is being evaluated to increase production and uranium recovery. Heap leaching will be replaced by conventional agitated tank leaching of the –590 µm ground ore slurry in a sulphuric acid medium. Replacement of the stripping reagent is also being considered.

Jan 1, 2012

By G. E. Viens, R. A. Campbell, G. N. Banks

A survey of the literature reveals wide differences in the procedures used in making iron ore pellets and in the properties of the pellets obtained. In this paper, the methods of production and the properties of pellets, as reported in the literature, are examined in an effort to determine what correlations exist between them. An attempt is also made to determine the levels of the properties of pellets which are considered acceptable and desirable in modern practice. M UCH has been written regarding the important changes which have been taking place recently in the iron ore industry. As the demand for ore has increased and the supply of direct-shipping ore has dwindled, tl1e problems associated with the utilization of lower grade ores ha\•e been intensely investigated and important advances in both beneficiation and agglomeration techniques have taken place. In particular, there has been a great deal of activity in connection with the pelletizing method of agglomeration. The superiority of pellets over raw ore has been demonstrated in blast furnace tests

Jan 1, 1962

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By H. Tsuruta, A. Fujibayashi, I. Sumi, A. Murao, R. Murai

Injection of biomass into blast furnace as alternative reducing agent is so effective for the purpose of mitigation of carbon dioxide emissions from steel industries, because biomass is considered to be carbon neutral raw materials. Certain amount of Palm Kernel Shell (PKS) is abandoned after Palm oil extraction process. To use as a reducing agent of blast furnace, PKS was carbonized and classified by 100 mesh sieve. To examine the gasification behavior of PKS carbide under the blast furnace conditions, several combustion experiments were conducted using hot model experimental furnace. The experimental results showed that the gasification efficiency of PKS carbide increased as the quantity of volatile matter increased. This tendency is the almost the same for the pulverized coal, so carbide of PKS can be used at blast furnace at appropriate amount of volatile matter that can be controlled by carbonization condition. In addition, the pressure drop of the furnace tends to decrease because the amount of ash in PKS carbide may be smaller than that of pulverized coal. PKS carbide is a suitable reducing agent in that respect.

Jan 1, 2015

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By N. M. Stubina, P. J. Lind

Barrick Gold is in the process of building several new mines and implementing new processes at existing mines for which metallurgical technology is of key importance. The roles of the company&apos;s Strategic Technology Solutions team and the Barrick Technology Centre are discussed within the context of their responsibilities within Barrick&apos;s Operations Support group. The paper will present an overview of the development of the technology centre from the former Placer Dome Research Centre to its current form supporting strategic technology, capital projects, and operating sites. Novel approaches to research and development will be presented as well as an overview of some of the technologies developed from bench-scale to pilot-scale, and beyond.

Jan 1, 2011

By Terence M. Gordon, Mati Raudsepp, Gregory M. Dipple

Four methods of measuring mineral abundance in a rock are examined for their potential in assaying for high-tech industrial minerals. One method uses X-ray powder-diffraction data and the other three rely on whole rock chemical data and information on mineral assemblages and mineral compositions. All four methods were employed to estimate wollastonite content in diamond drill core of skarn collected as part of an exploration program and are compared to visual estimates of wollastonite content from core logs. These techniques for assaying wollastonite span a considerable range ofaccuracy and expense, and combined, define a non-linear relationship between these variables. Accuracy increases rapidly relative lo expense up to total costs of about $50 per analysis. Assay methods in the $50-100 per analysis range have associated errors of 5-10% relative and probably suffice for most exploration programs. Improvements in accuracy above this level require a much larger investment. The most expensive assay technique (-$300 per analysis) yields the most accurate measurement of grade (relative error -1%). Its application may best be limited to periodic checks on other assay techniques and for fine-tuning ofmineral separation procedures.

Jan 1, 2001

By Omero Alonso-Gonzalez, Sergio Haro-Rodriguez, Ricardo Solis-Rodriguez, Francisco Alvarado-Hernandez, Juan Antonio Gonzalez-Anaya, Héctor Rene Vega-Carrillo

"Precious metals are currently associated with refractory minerals such as telluride (Calaverite, Sylvanite, etc.) and selenium (Naumannite Ag2Se), which are difficult to dissolve through traditional methods, therefore it is necessary to perform a pretreatment (oxidative or roasting) preceding the process of leaching by cyanidation. In this preliminary work the aim was to study the use of solvent extraction to remove tellurium and selenium ions from a synthetic cyanidation effluent, with the purpose of recycling the cyanide back to the process. For the extraction of these anions, TeO32- and SeO42-, tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (Amine F) were studied as extractants, using nonylphenol as a modifier in the organic phase (trimethylpentane). The results show that it is possible to recover 82% of selenium and 10% of tellurium from synthetic solutions containing either 20 mg/L Se or 20 mg/L of Te, respectively The Se or Te mole ratio to cyanide was 1:4.INTRODUCTION In relation to extraction of precious metals, the cyanidation process has been in use for over a century and despite environmental and toxicological problems it remains the most widely used and economical process available. In the late 90s, there were great efforts to recover gold and silver from refractory ores, which is difficult to do by simple cyanidation. To improve gold recovery from tellurides and selenides that occurs in some new mines, the ores are pretreated by roasting. This is one of the most effective ways of rendering refractory gold ores leachable as well as being a fast pretreatment process compared with bio-oxidation or pressure leaching (Aylmore, 2001). The most important tellurides minerals are Calaverite (AuTe2) and, Silvanite (Au, Ag)2Te4). In the case of selenides, minerals include Naumannite (Ag2Se) and Aguilarite (Ag4SeS) (Ostroumov et al., 1989). Examples of deposits containing telluride include La Bambolla Mine (Sonora, Mexico), Cripple Greek (Colorado, USA), and Kalgoorlie (Western Australia) (Aguayo et al., 1996). The main purpose of this work was to explore the feasibility of using quaternary ammonium salts such as: tallow trimethyl ammonium chloride (Quatarmina TPR) and hexadecyl trimethyl ammonium chloride (amine F) to extract tellurium and selenium anions from aqueous synthetic cyanidation effluents, so that the cyanide solution could be recycled back to leaching process. The tests were performed on synthetic solutions similar to those found in a mine: 20 mg/L Te as TeO32-, 20 mg/L Se as SeO42- and mole ratio to cyanide was 1:4. using an alkaline medium with pH ranging from 8 to 12. Two aspects are evaluated in this paper:"

Jan 1, 2017

By M. A. Halim, V. I. Lakshmanan

Recycling is one of the key elements for sustainable process development for the recovery of value-added products and reducing environmental impact. Process Research ORTECH Inc. has developed several innovative and sustainable technologies, which minimizes the use of water, and chemicals for the recovery of gold, vanadium and gallium from secondary sources by maximizing the recycling of reagents, and reuse of water from process effluents.

Jan 1, 2015

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

"In response to mine head grades declining and orebodies becoming more complex, Glencore Technology has developed an alternative method for recovering economic minerals once leached into solution, rather than relying on conventional flowsheet options. The method involves the precipitation and separation of base metals from solution with limestone or lime. The final grade of these precipitate is not usually high enough to attract favourable terms of sale due to dilution from gypsum and sulphate salts. A set of operating conditions have been developed to allow the separation of the base metal precipitate from gypsum by exploiting the difference in particle size. A high-grade oxide product can be easily separated from the gypsum stream at very low cost. This process was originally developed by Glencore for zinc and copper systems. This paper reports on the successful application to nickel and cobalt, and this process has significant advantages over the incumbent precipitation process utilising magnesia.INTRODUCTION During evaluation of transitional and oxide zinc ore deposits during the 1990’s, Noranda Inc. (now Glencore) developed a sulphate based ore leach process to extract zinc into solution. For flowsheet development, conventional schemes dictated that once the zinc was dissolved in an acidified solution it was recovered by means of purification or solvent extraction followed by electrowinning and casting to produce zinc ingots. The deposits Noranda evaluated were high grade but had a relatively short mine life (10 years) and economic analysis showed that the projects couldn’t sustain the investment of a full zinc refinery. Compounding this problem was the lack of power supply infrastructure and the high power cost in the region. Noranda then evaluated alternative means of recovering zinc from solution. Laboratory testwork showed that a high-grade zinc precipitate (+50 wt% Zn) could be produced as an oxide, carbonate or sulphide by contacting acidified zinc sulphate solution with a number of reagents including soda ash, sodium hydroxide, and sodium hydrogen sulphide. Economic evaluation showed that the cost of the reagents are prohibitive, especially when the final product is still a metal intermediate (ZnO, ZnCO3 or ZnS). Noranda then continued to focus on fine zinc oxide precipitation for supply into the automotive tyre industry as this product would attract favourable terms of sale as a premium on Special High Grade (SHG) zinc."

Jan 1, 2017