Search Documents

By M K. C Roberts, M G. Magwaza, J W. L Hanekom, P Piper, R Lousteau

Due to the perceived potential to extract the second economic manganese seam at its Black Rock Operations in the Northern Cape Province, South Africa, Assmang commissioned an investigation with respect to mining method and sequencing of the two orebodies in 2007. Based on this initial study into multiseam potential, conditions and impacts, the rock engineering aspect was expanded to determine conceptual rules to govern the extraction of both manganese seams using the normal bord-and-pillar layout implemented at this operation. This work included the theoretical analysis using basic pillar design practices and numerical modelling, including the use of Map3D, UDEC and Phase2 codes.In 2013, Assmang launched a large-scale investigation into the potential to increase mine output from all possible manganese sources at the operation. Included in this investigation was the requirement to confirm or modify the conceptual multiseam extraction rules to implementation. As part of this confirmation process, stress measurements, borehole camera audits and additional numerical modelling were performed at a particular site on the operation where a limited extraction of both seams had been undertaken. The results obtained from this process provided confidence in the conceptual extraction rules and allowed the derivation of final extraction rules that will be implemented at the operation as the multiseam mining process becomes more widespread.CITATION:Hanekom, J W L, Roberts, M K C, Magwaza, M G, Lousteau, R and Piper, P, 2014. Confirmation of multiseam extraction rules for Black Rock Manganese Operations, Assmang, Northern Cape, South Africa, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 107–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By X Li, W McKeague, M S. Powell

This paper explores the importance of operators in the overall efficiency of mineral processing plants. With the potential of future control configurations becoming more remote, it is time to review the implementation of control and utilisation of operators. This paper is based on a preliminary review of operators and control room operations and clearly shows that, in the minerals industry, operations are typically run in a reactive mode (with a focus on ensuring equipment operation), rather than in a proactive mode (with a focus on optimising the process performance). The primary reason for this misguided approach is the short sighted thinking applied to the challenges of designing technology and organisational tools capable of addressing the essential operational needs: an approach which inevitably results in a disconnect between people and technology. Contrary to the popular approach of replacing operators with expert systems, the thesis of this paper is that the shift to more complex circuits, with higher demands on processing capability and control, will require the actual upskilling of operators. Experience in mineral processing and other industries indicates that expert systems cope well with small changes but are typically unable to respond to major changes in feed material and this is where the expert operator becomes crucial. Providing operators with ongoing high level training in process understanding, and restructuring how they interact with the plant and interface with the control system is the approach being proposed here - an approach surprisingly underutilised and often absent in the minerals industry today.CITATION:Li, X, Powell, M S and McKeague, W, 2012. Unlocking processing potential by empowering our operators, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The Grootegeluk coal beneficiation plant is situated near Ellisras in the Waterberg coal= field in the Transvaal, RSA. At this plant 15 million tons of coal bearing material per annum are beneficiated by means of two-stage heavy medium bath and cyclone plants. Because of the very low yield of 12 % coking coal product, run= ping costs are of the - utmost importance. For this reason extensive tests were carried out to establish the most effective crushing and bene= ficiation methods and suitable aquipment. At the second heavy medium separation stage, the near-gravity material (+ 0,1. g/cc) amounts to 45 % and daily plant performance ana=lysis is required to ensure acceptable plant efficiency. Beneficiation processes for the -0,5 mm coal originally considered were froth flotation, shaking tables, heavy medium cyclones and water- only cyclones. When the froth flotation route was decided upon, further test work was done to enable selection of the equipment most suitable for the particular requirements.

Jan 1, 1987

By C K. McKenzie, P Popov, B E. Papillon, I Kharitonenko

Flyrock produced by blasts in surface mining and quarrying is a major hazard that can result in serious injuries or property damage. This paper presents a fully integrated and automated approach for reviewing blast outcomes from a wide variety of rock blasting environments from the perspective of flyrock safety associated with blasthole collar ejections. The process is applied at a corporate level for an explosives service provider handling up to 100 blasts per day from mines, quarries and construction sites throughout the US.Flyrock risk minimisation has inspired research and the associated development of a reliable flyrock model to estimate flyrock ejection velocities and the resulting maximum projection distances of fragments. In spite of significant achievements in this area, flyrock incidents continue to occur, mostly due to implementation mistakes. An efficient preventive measure is continuous blasting process improvement that relies on on-site video recording, storage, automatic analysis and classification of the recorded blasts followed by the automatic generation of reports.In this paper, a novel blasting video analysis system that is capable of processing a large quantity of video records is presented. Blast analysis and parameter measurement are fully automated and are carried out using videos recorded with a conventional consumer camera. The blast video recording process does not require the use of surface markers, range poles or objects of a predefined size for scaling purposes.Although automatic video analysis is commonly used in many application areas, such as video surveillance, traffic monitoring and robotics, the algorithms that have been developed to recognise and track solid objects with well-defined shapes, textures and colours are not efficient at dealing with blasts, which, by their nature, have dynamically changing parameters. Moreover, very strong camera vibration caused by blasts that cannot be totally compensated by camera image stabilisers may cause conventional computer vision algorithms to fail.This paper presents novel computer vision methods developed for automatic tracking of the trajectory from a blast ejection point to the highest point reached by blast particles and the ejection velocity. The system also uses colour and motion analysis to detect the emission of toxic fumes during a blast. The solution is vibration tolerant and can differentiate foreground and background data, even in the presence of camera vibration. Moreover, the blasting video analysis method can automatically categorise correctness of the measurements and therefore indicate cases when additional visual inspections may be required to verify reports generated automatically.CITATION:Kharitonenko, I, McKenzie, C K, Papillon, B E and Popov, P, 2015. An automated system for flyrock and fume monitoring of blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Morey

Ok Tedi Mine is located eighteen kilometers from the Irian Jaya border in the Star Mountains, Western Province, Papua New Guinea. Sequential flotation concentrators produce a copper / gold concentrate for market, and a pyrite concentrate for environmental containment, with low sulphur tailings from the pyrite flotation sequence being discharged to river. Strict sulphur assay targets are set for the riverine discharge. Current porphyry and skarn ore blends from open pit operations at Mt. Fubilan will cease by 2017. However, drill cores indicate an economic ore body in the skarn ores surrounding and below the current pit limits. With proposed mining from a western pit wall ‘cut back’ and an eastern pit wall underground operation, potential for ore ageing in sub level cave underground stockpiles is apparent. With little information in the literature, Ore Ageing test work at prefeasibility level consisted of multiple one tonne stockpiles of -50 mm crushed rock. For the bankable feasibility study, a successful test work program was implemented utilizing 40 tonne ROM ore stockpiles composed of exposed pit extensions of future ores. Realistic ageing profiles of Skarn ores were obtained from one tonne monthly samples subjected to laboratory testing. Test work outcomes included:• Similar ore ageing profiles from both the pre feasibility study (PFS) and feasibility study (FS) programs, suggesting ore susceptibility to oxidation has greater effect in ore ageing than rock size for Ok Tedi skarns. • Laboratory rougher flotation of pyrite showed significant variation in sulphur recovery rate, suggesting three classes of pyrite floatability.• Laboratory rougher flotation of both copper and pyrite for up to 19 months ore ageing from 11 stockpiles, suggested three stages in the ore ageing process.

Aug 8, 2011

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By M Frenzel

At the last MassMin Conference in Sudbury, Caterpillar’s vision of a continuous mining concept for block caving operations was presented on the background of global raw material demand and its continuous increase. By analysing today’s structure of mining processes in block caving, the paper (Krings, Steinberg and Frenzel, 2012) highlighted the main bottlenecks in the process chain and identified conceptual solutions by help of a case study. The main focus was the paradigm shift from discontinuous batch type operation to a continuous mining process of the blocks.In 2016, the strategic vision has taken major strides forwards and remote continuous operation has become a reality. Caterpillar’s continuous operation system – the Rock Flow system – was successfully installed in Codelco’s Andina mine and start of operation is scheduled in the first half of 2016.Based on continuous product developments, this paper sets the focus on two main aspects of continuous mining. First, field experiences of the Rock Flow system will be shared, highlighting the Andina project course from system installation, to commissioning and successful system start. The second aspect concentrates on the system and mine layout as discussed in the case study scenario in MassMin 2012 (Krings, Steinberg and Frenzel, 2012).Based on Caterpillar`s continuous product development, the Rock Flow system set-up and panel design were modified for a general roadway design and drawpoint layout. The new design allows an optimised use in block preparation phase (spreading) and full production phase (reaping), operating a fleet of load-haul-dumps (LHDs) and Rock Flow systems. The combined use of the two technologies optimises the mining process in every stage of block life and significantly increases the performance of the continuous block caving operation in the production panel to pave the road for the next generation of super caves.CITATION:Frenzel, M, 2016. New continuous production system in block cave mining – the rock flow system, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D A. Williams, P J. Chapman

Constructing upstream raises with tailings is an accepted and cost-effective practice in Western Australia, where the climatic conditions are favourable, desiccation (and hence overconsolidation) occurs rapidly due to air drying and there is a perceived low seismic risk. This is in contrast to many other settings, where there is either a positive water balance, high seismicity or a combination of both. In recent times, there has been an increased focus on seismicity in areas of Australia that have historically been considered to be of low seismic risk. The increased focus is driven by two recently published documents used by tailings practitioners and increased awareness from corporate entities, particularly those with mines in high-seismicity regions such as South-East Asia and South America (particularly Chile).The increased awareness has resulted in increased rigour being applied to seismic design of tailings storage facilities (TSFs) in general, and particularly upstream-raised TSFs. This paper compares the results of a seismic stability assessment for an upstream-raised TSF located in the Goldfields region of Western Australia, which has historically been considered a low seismic area, with a seismic stability assessment carried out for a crossvalley TSF containing similar tailings but located in a high-rainfall, high-seismic setting in South-East Asia. The influence of the adopted design earthquake values on the results of the assessments and the potential impact of the maximum design earthquake (MDE) on the design approach is presented for both cases. The results indicate that although the Western Australian site is located in an area thought to have low seismic risk, the screening level analyses suggest that the MDE could result in liquefaction of the tailings materials. Not surprisingly, liquefaction was also indicated for the South-East Asian site. The outcomes of the assessment are also presented.CITATION:Chapman, P J and Williams, D A, 2015. Seismic design of upstream-raised tailings storage facilities in a semi-arid, low-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 157–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

The paper describes the studies conducted to date on the short term adsorption/desorption of gases in coal from the point of view of developing techniques to predict imminent outbursting conditions in coal mines. A number of different parameters such as'dP express, K' and AV 0/60 etc. which have been effectively used overseas were studied on samples of coal from Westcliff and Leichhardt Colliery. Results indicate that these do not seem to be valid indices for predicting an outbursting condition. Based upon desorption isotherms, a new index defined as "L" has been developed which shows promising results. This index is in a position to differentiate the changes in the structures of coal and its proness to outbursts. The "LZ value determinations and its usefulness opens a new field where it would be possible to determine outbursting conditions from existing drill cores obtained during exploration studies or from long holes drilled in advance from underground workings. The index is more or less independent of the time elapsed between the extraction of a sample and the conduct of the test. The test for "L" can be conducted'on site or in the laboratory. The test is simple, easy to carry out and the "L" value for a sample can be calculated in less than 20 minutes. It could be adapted as a routine test for monitoring outburst conditions in mines.

Jan 1, 1980

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By A Bossilkov

Although environmental and sustainable development reporting has now become widespread in the Australian mining and minerals processing sector, there remains a great deal of diversity in reporting contents and practice. Moreover concerns remain about the effectiveness of reporting for delivering the companyÆs business case for sustainable development as well as for communicating sustainable development performance to a range of external stakeholders. This paper therefore reviews the status of sustainable development reporting in the Australian minerals processing industry. Pertinent international and national developments are briefly captured, leading to a discussion of the framework for integrating sustainable development reporting with sustainable development management (as proposed by the World Business Council for Sustainable Development). This leads to a discussion of the results of a comparative review of sustainable development reports of a cross-section of eight Australian resource companies. Best practice elements are highlighted in regard to reporting on company context, governance, performance and assurance.

Jan 1, 2004

By Ride G

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in and areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1980

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

By D Landriault, G W. Wilson, L Langetine and

Engineered soil covers are used for final closure options for both waste rock and tailings disposal facilities. Currently, cover construction requires excavation of appropriate cover material from a nearby site. If no suitable materials are available, the mine operation may have to ship appropriate materials long distances to the site before the construction of the cover can even begin. This has led to the proposal to engineer cover materials using existing waste materials from the mining operation. The paper presented here describes the results of a laboratory scale testing program to evaluate the potential for blending waste rock, smelter slag and tailings for the creation of a suitable cover material at a site in Canada. Tailings from the local mill, waste rock and slag were collected in the field and blended to create a material with an air entry value similar to the tailings and with physical strength similar to the waste rock. Testing indicated this mixed material could be blended at a consistency of a paste and was suitable for pumping. It can also be compacted to a high-density material. The preliminary results show that it may be possible to blend waste rock, slag and tailings into a material that can be utilised in the construction of a water retaining cover.

Jan 1, 2003

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998