Search Documents

The pilot scale testing of Australian coals for their NO, emissions was carried out at the ACTC to investigate the influence of coal properties, furnace conditions and different NO,, control strategies on NO,, emissions. The NOx emissions for the Australian coals tested were found to vary over a wide range and primarily depended on combustion temperature and excess oxygen conditions. These coals did not exhibit any fundamental difference in NOx levels to other world coals. Under similar combustion conditions, the conversion of coal nitrogen to NO. was found to be best correlated with coal rank parameter, R, max per centage. The use of staged combustion as a control strategy was shown to reduce their NOx levels by 56 - 77 per cent.

Jan 1, 1991

By S Nie, I Bergqvist, F Ouchterlony

In blasting, a few or many cracks are driven from the borehole into the rock. But what causes the cracks? The most common theory of breakage consists of two stages; first the shock wave causes radial cracks to form around the hole then the gases penetrate into the cracks, and widen them and make them longer. Another theory presented by Brinkmann suggests that the back damage is primarily controlled by shock and that the gas penetration is the mechanism controlling breakout of the burden. He did his experimental work using blasthole liners. Recent research at SveBeFo has examined this matter further. In a quarry a number of benching holes have been blasted simultaneously. In some of these holes tubular Swellex bolts were inflated and decoupled charges put inside the tubes without stemming. Other holes were identically charged but without the lining. Finally some holes were also stemmed. After blasting the cracks in the remaining rock were studied. There was no difference in crack lengths between holes charged normally (no stemming) and holes where the charges were inside the bolts. On the other hand when stemming was used, the crack lengths increased for some explosives but remained the same for an emulsion explosive. In another set up blasted granite blocks were charged in the same way as above. Then we could also measure the bore hole pressure. The pressure gauge consists of a small carbon resistor inside a steel cylinder. It is called LHM (Location-fixed Hydrodynamic Measuring Cup) and is placed at the bottom of the hole. A smaller exit hole from the bottom is drilled for the cables. The paper presents the technique and the results obtained from both the quarry blasting and the blasting of the blocks.

Jan 1, 2001

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993

Since gold was first discovered, mining development in the West Australian goldfields has been heavily dependent on the location of groundwater both for potable and mineral processing supplies . The location of adequate and economic sources of water has been a constant challenge to both explorers and developers throughout the history of the goldfields. The provision of a piped supply from Mundaring in 1903 greatly alleviated pressure on scarce resources, lowered mining costs and permitted the orderly development of infrastructure. However, increases in the demand for water resulting from new mineral discoveries over the past three decades has led to renewed pressures for more local supplies to be established. Wide-ranging groundwater exploration took place in the late 1960's and early 1970's, also, more recently, in support of intensified gold exploration. The collation and interpretation of the hydrogeological data from the whole goldfields region indicates that despite a low mean annual rainfall of between 180 and 350 mm, quite marked differences exist between the rates of groundwater recharge in different parts of the area, In general, these can be shown to diminish in a southerly direction contrary to a trend towards increases in annual rainfall. Recharge rates are related mainly to differences in rock weathering pattern, geological structure and physiography. The same differences have controlled the pattern of groundwater salinity and the magnitude of groundwater storages associated with the palaeodrainages. In the vicinity of the northern and western watersheds with the Gascoyne, the superficial sediments tend to be thin, may have calcrete in the section and contain moderate storages of brackish or even fresh water. This contrasts with the lower regions of the palaeodrainages where calcrete is absent and deeper erosion has permitted the accumulation of relatively large thicknesses of fine-grained sediments which are saturated with hypersaline water and constitute substantial storages. Account must be taken of these characteristics if water supply sources are to be optimised to meet the growing demands for groundwater in the region.

Jan 1, 1988

By M I. Pownceby

High temperature roasting studies on chrome-spinel contaminated ilmenite concentrates showed that sulfur, introduced through a sulfidising roast treatment, selectively reacted with the chromium in the spinels. The roast treatments were carried out in a laboratory scale rotating drum kiln using a standard Becher-style heating profile (10 h, 1075ºC), char as the reductant, and variable amounts of added elemental sulfur (0 - 3 wt per cent).After roasting, bronze-coloured grains were visible representing chrome-spinels that had undergone selective sulfidisation. SEM imaging of the products showed that sulfur was preferentially concentrated in ~5 - 15 µm thick rims fully enclosing the chrome-spinel grains. The sulfur-rich rims became a sink for manganese (Mn) from the ilmenite resulting in the rims being rich in Cr-Mn-Fe-sulfides. Quantitative electron probe microanalysis of phases present within the rims identified two sulfide phases. The first sulfur-phase (S-phase) was low in Mn (1 - 3 wt per cent) and high in Fe, Cr and S, while the second S-phase was considerably higher in Mn (30 - 35 wt per cent Mn) and lower in Fe and Cr. The dramatic change in the composition of the chrome spinels after sulfidisation is likely to significantly alter their physical properties (eg hydrophobicity, conductivity, etc). This should make their physical separation from the ilmenite potentially easier than roasting/magnetic separation methods.

Oct 5, 2011

By L O’Connor, S C. Dominy

"Geometallurgy is an important addition to any evaluation project or mining operation. As a discipline, it seeks to maximise the net present value (NPV) of an orebody while minimising technical and operational risk. It also aims to promote sustainable development and initiatives by ensuring that all stages of extraction are performed in an optimal manner from a technical, environmental and social perspective. To achieve these goals, development of innovative technologies and approaches along the entire commodity value chain are being established (Glass, 2016). Geometallurgy has been shown to increase operational stakeholder collaboration, creating an environment for knowledge sharing and improved data acquisition and interrogation, with the end result being the integration of such data into mine planning and scheduling. All of these aspects create better business optimisation, utilisation of staff and targeted and realistic key performance indicators.The mining industry faces numerous challenges including, but not limited to:declining ore gradesgeometrically and/or internally more complex depositsdeep-seated deposits, with potentially high in situ stress regimesincreasing quantities of mine waste that needs to be managed appropriatelyhigher energy, water and chemical costsprocessing of more challenging and refractory ores – textural complexitiesstricter environmental/permitting conditions – so-called ‘licence to mine’increasing demand for specialist metals (eg rare earth elements, In, Ge, Te, Rh, Se, Ga and Li)commodity market volatilitya difficult funding environment.Given these challenges, geometallurgy provides the opportunity to control or at least manage some of them.CITATION:Dominy, S C and O’Connor, L, 2016. Geometallurgy – Beyond Conception, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

By O Rojas

The Telégrafo copper – gold deposit is located in the Centinela district of the Antofagasta region in northern Chile. Telégrafo is a porphyry copper deposit of Eocene – Oligocene age which has a total mineral resource in measured, indicated and inferred categories equal to 2.6 billion tonnes with an average grade of 0.38 per cent copper.Currently the project is in the prefeasibility study phase, including an infill drilling campaign to improve the knowledge of the deposit that should result in an improvement of the mineral resource classification. In this context was decided to review the classification criteria in order to optimise the drill hole density necessary to support the project.This paper presents an application of conditional simulation to evaluate the risk related to drill hole spacing, using a geostatistical approach that mimics the process of evaluation of resources from the perspective of geological modelling and grade estimation. The first step of the approach is the generation of conditional simulations using the available samples to generate several plausible scenarios of the deposit in terms of copper grades and geological units. These scenarios are considered as the unknown reality of the deposit and sampled by synthetic drill holes in order to replicate the geological model process and copper resource estimation. In this way it is possible to establish differences between the possible scenarios and the generated resource estimation models for several simulated drill hole spacing alternatives. These differences or errors can then be quantified in terms of estimated mean, metal content and tonnage over different production volumes.The resulting errors were useful in assisting the decision making process related to the design of drill hole spacing for each category of mineral resource in the Telégrafo project, and to redistribute the budget associated to the drill campaigns for the next stage of the project.

Aug 22, 2011

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

By M Dohm, L Pretorius

This paper provides a brief historical background to the approximately 12-year project that led to the revision of rope selection factors in the South African regulations, thus providing the ability to hoist economical payloads from single lift ultra-deep shafts. The efforts over the past 20 years have led to the revision of the legislation pertaining to rope selection factors, the redesign of rope constructions to meet the required duties associated with ultra-deep shafts, codes of practice for the design, operation and maintenance of winding plants, and a code of practice for the condition assessment of winder ropes. As a consequence the Moab Khotsong ultra-deep hoisting system could be developed and installed, with the assurance of predictable performance. Access to deep orebodies by means of single lift, ultra-deep shafts has a critical impact on the life cycle costs and efficiencies of ultra-deep mining complexes. A brief description of the main components of the hoisting system at Moab Khotsong is presented. An in-depth review of the development process applied to ensure a stable, safe and cost-effective rope construction for the ultra-deep Moab Khotsong shaft follows. The paper concludes with an overview of the experiences gained during the installation and commissioning phases of the winder, as well as operational and maintenance issues.

Jan 1, 2005

By Palmer DJ

Mercury is introduced into EZ's electroly tic zinc/sulphuric acid plant complex at Risdon, Tasmania, in zinc sulphide concentrate. Mercury is volatilised during the roasting operation and then distributed in the sulphuric acid plant effluents and product acid. Following an investigation of the factors determining the mercury distribution, a plan was formulated to-provide an environmentally accep- table degree of mercury containment at Risdon. This paper discusses details of the various control measures investigated and out- lines the reasons for selecting the particular procedures finally adopted for the Risdon plant.

Jan 1, 1980

A comprehensive analysisof rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging, interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcorc is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure.

Jan 1, 1990

The Bureau of Mineral Resources has been engaged in regional geological and geophysical field work in the Alligator River and Cobourg Peninsula area since 1971, following the discovery of major uranium deposits. Geophysical work commenced with a regional airborne magnetic and radiometric survey which was followed up by some helicopter and ground work in August 1973. The interpretation of the earlier radiometric work is presented in conjunction with the results obtained from the follow-up work. Analyses of 100 outcrop and drill core samples collected have provided basic information on the physical properties and concentrations of uranium and thorium in various rock types. The uranium determinations were made by X-ray fluorescence and delayed neutron analysis, good agreement being obtained between the two methods. X-ray fluorescence was the main analytical technique used because of its ability to produce both uranium and thorium determinations.

Jan 1, 1975

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The Peko copper orebody is associated with a body of magnetite rock which it has partly replaced. The primary ore averages about 9 per cent. copper and 4 dwt. gold per ton and locally IS much richer. It consists essentially of chalcopyrite and unreplaced magnetite, with lesser amounts of pyrite, marcasite, pyrrhotite, cobaltite, bismuthinite, native bismuth and native gold. The earliest formed mineral is wolfram, and the latest formed is goethite, so that the temperature of deposition ranged from about 5000 C. to 1650 C. or lower.Oxidation extends to 270 ft., which is 100 ft. below the present water level. The oxidized ore consists of cuprite and native copper, and has replaced more or less massive chalcocite of a former zone of secondary sulphide enrichment. The present zone of secondary sulphide enrichment extends from about 270 ft. to 310 ft. depth.INTRODUCTIONThe Peko mine is about 6 miles south-west of Tennant Creek township in the Northern Territory, adjacent to a small outcrop of hematite rock that projects above an otherwise featureless "bull-dust" fiat.The copper-gold orebody being developed in this mine did not outcrop. It was first detected in 1950 by a surface diamond-drill hole (DDH.1), which intersected primary copper ore at a depth of 400 to 425 ft. This ore contained from 4 to 11 per cent. copper and 1 to 25 dwt. gold per ton. Since then a shaft has been sunk, and crosscuts and development drives have been opened on the 210..ft., 300-ft. and 400-ft. levels, which are also connected by winzes. Two diamond drill holes sunk from the 400-ft. level have intersected theorebody at about 450 to 460 ft., and a winze from the 400-ft. level intersected the lode from 445 to 500 ft. At this point it is 54 ft. wide, and averages 9 per cent. copper. More recently an inclined surface drill hole (Peko No. 1) has cut the lode at 856 ft. to 921 ft., equivalent to a vertical depth...

Jan 1, 1955

By S Hille, J Karageorgos

With the increased variability of todayÆs large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

In taking the chair at this meeting of the Australasian Institute of Mining Engineers, I feel it my duty to thank you for the honour you have conferred upon me by electing me President for the current year, especially as Bwken Hill is the birth place of the Institute and myself one of its foundation members. I will now endeavour to entertain you for a short time with a few reminiscences of Broken Hill from its inception. Beyond the fact that the mines on the Broken Hill lode have paid to their shareholders in dividends and bonuses no less a sum than £896,500, created and maintained a city of 25,000 inhabitants. supplied a large proportion of the revenue on the railways of a sister state, and made their influence felt throughout the 'commercial centres of the world, very little, I regret to say, is known by the general public as to the form, extent, or vastness of the ore bodies, or the mode of occurrence of the various classes of ore which have been found to exist in them. It has occurred to me that a short paper by the senior mining manager on the line of lode might prove interesting. There has been great difficulty in getting some of the figures relating to the field, the total output of metals from the Broken Hill mines not being obtainable from the Mining Department in Sydney j but an inscription on the foundation stone of the Technical College recently opened in this City, sets forth that the Broken Hill Mines started in 1880...

Jan 1, 1903

By W Malone, J Garrett

FLSmidth (FLS) has spent the last 15 years, working with customers and engineering houses to deliver innovative improvements in crusher safety, coupled with the latest, maintenance friendly, crusher design. The key focus being to prevent service personnel from working underneath the crusher during maintenance and obviate the need for personnel to be exposed to suspended loads when performing tasks such as, main shaft installation, for example. Improvements include: full top-service capability to ensure the safest and fastest way to disassemble the crusher for maintenance purposes, which also removes the requirement for a service cart; a selfaligning main shaft which ensures remote assembly is now possible, keeping service personnel well out of harm’s way; And rotable shells, or the ability to perform relines off-station, allows for quick shell ‘swap-over’ without the downtime associated with removing, refitting and curing time associated with epoxy backing. The high flow spider improves large material entry into the crusher, reducing blockages and downtime and therefore maintains crusher capacity. Each size of crusher in the range comes with an option to increase the standard feed opening to a larger one if desired to compensate for ‘blocky’ or ‘elongated’ feed material, a common problem for Pilbara hematite iron ores. Power capability has also been increased with a maximum of 1500 kW, to match the higher throughput capacities being achieved. This due to uprated eccentric speeds and larger discharge annulus. Increased eccentric throws and mantle diameters are also now a reality, when compared to more traditional designed gyratory crushers. To keep up with the improved design features of the Mk V, digitalisation has also been upgraded to maximise performance capabilities to ensure that the most efficient reduction and throughput capacities are achieved, whilst utilising the higher powers now available as standard. Condition monitoring ensures that the crusher is at its optimum operating capability by monitoring and adjusting the crusher settings via feedback from additional sensors, ie main shaft spin, temperature and vibration. Camera monitoring capabilities are available as is an advanced oil contamination monitoring system. As a result of the above design improvements, it will be shown that the Mk V range offers benefits such as: enhanced safety features, increased availability, faster maintenance turnarounds, higher power utilisation, equivalent product size at higher throughput capacities and with Remote operation capabilities. All of which result in a gyratory crusher with higher levels of safety and a lower per tonne operating cost.

Sep 18, 2023