Search Documents

By H Phillips, A Spaeth, B Belle

There are several well-known, extensively researched and tested methods of suppressing a coalmine methane and coal dust explosion. The choice of method used is dependent on the legislative requirements of each country, which in turn are influenced by mining conditions in that jurisdiction. For example, seam gas content and the dustiness of the coal will combine to create the hazard, while the physical and chemical properties of the seam might influence the possibility of ignition sources such as frictional ignitions. The mining method and layout will also influence the choice of preventative or proactive suppression devices. The decision as to which method is approved and adopted should be based on currently tested and available technology and the latest research outcomes, and should be subjected to a rigorous risk assessment, since a methane explosion propagating into a coal dust explosion cannot be countenanced.Every new technology must undergo stringent tests and these tests must be certified by accredited research facilities or laboratories. Upon approval, an explosion suppression system or the critical components of such a system should be tested in a more realistic environment. This environment can ideally be found in an operating underground mining section for evaluation purposes. Based on the insight gathered in such an environment, a realistic evaluation of the effectiveness of a potential system can be carried out. The explosion suppression system described in this paper has been tested on numerous occasions at accredited test facilities. The technology described in this paper has been used in various applications in underground coalmines and has been adapted to fulfil and exceed the requirements set out for methods currently in use. This paper describes the underground evaluation results of the latest technology in active suppression systems as used on continuous miners was adopted to perform as a roadway explosion barrier.CITATION:Spaeth, A, Belle, B and Phillips, H, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Australian Mine Vent Conference 2017, pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Acid soluble calcium is depleted in drainage sediments from hydrothermal alteration centres in the Coromandel Peninsula. The routine analysis of acid-soluble calcium on drainage samples is an economical and effective technique for outlining hydrothermal alteration centres in volcanic terrains.

Jan 1, 1979

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

Lean Iron Ore Beneficiation in India

Sep 13, 2010

Fine Coal Evaluation by Gravity Methods

Sep 13, 2010

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Two Variable Real-Time Algorithm for Cone Crusher Control

Sep 13, 2010

By M Baker

Biodiversity offsets are conservation actions intended to compensate for the residual, unavoidable harm to biodiversity caused by development projects. The use of biodiversity offsets in the context of mining has significant potential for enabling mining to take place in areas with biodiversity values, where it would not otherwise be possible to meet the relevant legal tests under the Resource Management Act 1991, and potentially the Conservation Act 1987. This paper looks at the concept of biodiversity offsets (and environmental compensation generally) both in New Zealand and internationally, and considers how lessons learned overseas may be adapted for this country. In New Zealand the practice of biodiversity offsets and environmental compensation is ad hoc and variable. The challenge with biodiversity offsets is to establish a transparent and coherent means of identifying the overall priorities and objectives of adopting such an approach, as well as how the relevant values are measured and protected. Establishing a methodology for quantifying biodiversity value, and the need for clear policy guidelines on biodiversity offsets are identified as key areas in need of wider discussion.

Jan 1, 2007

Recovery Efficiency Study on Ilesha Placer Gold Ore by Flotation Using Locally-Sourced Frothers and Collectors

Sep 13, 2010

Permitting, engineering and evaluation, detailed design and construction aspects of the Golden Cross goldmining project in New Zealand are briefly reviewed. The extremely lengthy and complicated governmental approval process together with the delaying tactics of opponents of the project are outlined and comment is made on aspects of the draft legislation proposed as part of the overhaul of New Zealand's resource management laws.

Jan 1, 1990

Brunswick Mine, one of the largest underground zinc mines in the world, is scheduled to close in 2010 after almost half a century of production. All mines eventually close; some suddenly as a result of unsustainable economic or technical conditions and others, as in our case, as a result of the depletion of the orebody. When the mine is the most significant employer and an economic driver in the region, it is key that the closure is handled in a planned, communicated, well-executed fashion. The following paper documents strategies, plans and activities that are currently taking place in order to ensure a seamless closure that satisfies all stakeholders including employees, management, regulatory bodies and the public. It is an important deliverable for the company that the good will, credibility and reputation that has been built up over the years is sustained throughout the closure process and beyond. A life of mine labour agreement with the unionised workforce, staff retention and recruiting programs, regulatory closure plans, communications and transition adjustment activities will be discussed. The use of a stage-gate style project management tool analysing the risks and key deliverables will be highlighted. It is hoped that the concepts and approaches discussed here may be of value to other operations that will be faced with closure, and its inherent challenges, in the not too distant future.

Jan 1, 2006

By G J. Corbett, T M. Leach

Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of youngerPacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By D C. Grant, D J. Goudie, E Baird

The Scanning Electron Microscope – Mineral Liberation Analyzer (SEM-MLA) laboratory, as part of the Core Research Equipment and Instrument Training (CREAIT) network of laboratories at Memorial University, NL, Canada, has recently published efforts towards increasing the throughput of automated mineralogy systems by producing single-step trans-vertical moulds, rather than traditional 30 mm polished epoxy moulds. Due to the small particle size of iron ore grains in the -200 mesh size fraction (<75 µm), not all of the surface area on a mould is needed for measurement in achieving good statistical representation. In a new study, trimming of the excess area of a mould results in a smaller sample and increases the quantity of unique samples that can fit in a newly designed trans-vertical adapter for a FEITM MLA 650 field emission gun (FEG) scanning electron microscope. The complete analysis, using a newly designed sample block holder capable of holding 98 samples, required 57 hours of running time where each sample had an average of 33?400 particles measured and identified. The analysis was calibrated to allow for off-line discrimination of hematite/magnetite. The calculated Fe-assay values derived from MLA results were compared to those from bulk sample chemical assay. This shows the Fe assay having a correlation coefficient of >0.99 when the particle count is greater than 20?000. This study represents the most expedient method yet reported to prepare well-polished samples and analyse them in a timely manner that can allow for quicker results in process mineralogy.CITATION:Grant, D C, Goudie, D J and Baird, E, 2017. Analysis of individual - mesh iron ore samples in a single Scanning electron microscope automated mineralogy session, in Proceedings Iron Ore 2017, pp 535–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C J. N Wilson

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c.0.28 m3 s-1. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust that precludes the development of long term magmatic cycles at Taupo. Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

Grinding and Flowing Investigation on Dry Stirred Ball Milling in Order to Determine the Influence of Grinding Aids Huge difficulties of the great ultra fine ground material production in dry stirred ball mill are the cohesion and agglomeration of the particles. During grinding the material stick on the grinding wall and the grinding media furthermore the grinds start cohere, making aggregation and agglomeration to appear. Due to these effects the particle size will not decrease after a certain value during grinding and the energy demand increases significantly. According to experience on fine grinding in ball mill, it is well known that these effects can be reduced with the use of grinding aids. The influence of grinding aids has three different effects: due to the adsorption strength reduction (Rebinder effect) the grinding resistance of the material decreases; the surface energy diminishes and the agglomeration liability decreases; and the flow properties of material improve. The aim of this study is to investigate the flow properties of fine grinds and the effect of grinding aids on flow properties in case of dry stirred ball milling. In addition, the influence of grinding aids was investigated based on the particle size distribution and specific surface area of grinds and the specific energy demand of grinding. The examinations were carried out with three different model materials (limestone, clinker, quartz) using the usually applied grinding aid. The flow properties were measured by the Jenike shear cell; the particle size distribution and specific surface area were measured by laser particle size analyser (Fritsch Analysette 22), grinding energy demand was measured with microcomputer controlled digital energy meter. It can be said that under certain measuring circumstances the influence of grinding aid on flow properties can be demonstrated by Jenike shear cell, so the grinding result is in correlation with the flow properties of grind.

Sep 13, 2010

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

With a price slowly rising above US$35 per ounce gold became a mineral worthy of prospecting and mining endeavour in the early to mid 1970s. Fortune therefore appeared to smile onNew Zealand with its favourable geological environment for gold and past record of major gold production from both hard rock and placer deposits. This was a particularly welcome development as the post war years, including both the base metal exploration boom of 1967/1971 (which produced major nickel, iron and bauxite mines in Australia) and the earlier period of uranium exploration failed to produce any mines in New Zealand with the exception of the small Tui Mine and iron sand mining. Whilst hard rock mining now appears imminent it is 15 years further along the track since the 1967/1971 exploration boom and eight years since the upsurge in prospecting for gold in 1978. New Zealand still has no hard rock base or precious metal mining. This is not for want of proven or potential gold mining situations for these clearly exist at Waihi, Monowai Reef, Golden Cross, MacRaes Flat and elsewhere.

Jan 1, 1986

By V Cullinan, D Buchanan

The Brunswick plant is located in Costerfield, approximately 40km east of Bendigo in central Victoria. Crushing, grinding, gravity gold concentration and flotation methods are used to produce a saleable gold concentrate and an antimony-gold flotation concentrate. This paper discusses the improvements made within the processing plant which have resulted in a 99% increase in throughput over nameplate capacity of 6 250 average tonnes per month to 12 445 average tonnes per month and increases of 12% gold (from 2007 average of 78% to 2014 average of 90%) and 16% antimony recovery (from 2007 average of 79% to 2015 average of 95%). This combined effort has resulted in an increase of equivalent gold ounces (AuEq oz) produced from 2010-2014 of 15 872 to 82 574 – a 66 702 increase.AuEq oz= Au oz +Sb t × Sb (US$/t)Au (US$/oz)CITATION:Buchanan, D and Cullinan, V, 2015. Improvements in bi-metal production at the Brunswick Plant, Costerfield, in Proceedings MetPlant 2015, pp 267–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Study on Basic Theory of the Grain Settlement in Fluidised Bed This paper takes thick goal grains (less than 1.5 cm) as research object. According to different densities and particle sizes, thick goal grains are divided into 20 kinds of narrow density and narrow size level average grains. Free settling and hindered settling tests are respectively carried out in ?100 fluidised bed thick goal separators. Hindered settlement includes hindered settling velocity test and measurements of suspension density. Results show follows. (1) Fluid state in separator belongs to transition region. Alien's law is the appropriate formula of thick coal particles free settlement terminal velocity. (2) The main factors affecting hindered settling velocity are the number of solid particles in medium and the structure feature of the particle group. The bigger volume fractions of solids ? is, the smaller decreasing velocity coefficient of particle hindered settlement ¯ becomes. In the organism from bottom to top, density of suspended particles in fluidised bed gradually decreases, but near the top of the suspended particles, the density increased slightly. With increase of density and size, suspension density reducing extent increases from bottom to top of separators.

Sep 13, 2010

Lead Removal from Contaminated Soils with Chelating Agents

Sep 13, 2010