Search Documents

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By T. J. Serenko

The epithermal deposit is hosted by Tertiary volcanic rocks that lie between mid-Miocene normal faults of the Northern Nevada Rift. Petrographic, laser-ablation and metallurgical observations suggested that the gold occurs in two principal forms: native (and electrum) and disseminated in arsenopyrite. It was proposed that gold is distributed between two parageneses with distinct mineralogical associations. Detailed downhole geochemical study supported the observations. Concentrations of Au, Ag, As, Sb and Se were determined from drill core and reverse-circulation cutting composites and contoured on cross-sections. Gold was indeed shown to have a bimodal distribution with the two parts separated spatially and perhaps temporally, implying that two separate genetic processes acted to concentrate gold at Mule Canyon

Aug 1, 1995

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By M. Beth McClenaghan

This paper summarizes diamond exploration techniques used in glaciated terrain, focusing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments are essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 to 0.5 mm) fraction of heavy mineral concentrates prepared from glacial sediment samples is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and REE, the relative importance of which will depend on kimberlite composition as well as that of the surrounding bedrock.

May 1, 2002

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol&apos;s No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By WILLETT G. MILLERS

GENERAL RECEPTION COMMITTEE.-Willett G. Miller, Chairman; F. G. B. Alan, Hon. Frank Cochrane, Eugene Coste, Thomas W. Gibson, Cyril W. Knight, J. C. Murray, 0. N. Scott, Alan Sullivan, J. B. Tyrrell, J. W. Wells, A. B. Willis. COBALT RECEPTION COMMITTEE.-Arthur A. Cole, Chairman; Will. Ask with, R. W. Brigstocke, Robt. Bryce, Fred Coombs, M. I. Culbert, I. R. Drummond, J. W. Evans, A. Ferland, F. N. Flynn, E. L. Fraleck, S. R. Heakes, Joseph Houston, D. L. Jemmett, I. R. Jones, Major Leckie, Capt. Jack Leckie, R. W. Leonard, W. H. Linney, Alexander Longwell, Frank Loring, Murdock McLeod, John Martin, D. B. Rochester, W. E. Running. COBALT RECEPTION COMMITTEE (Ladies).-Mrs. A. A. Cole, Mrs. A. Edwards, Mrs. R. Jennings, Mrs. S. H. Logan, Mrs. A. Longwell, Mrs. H. F. Marsh, Mrs. J. Smith. SUDBURY LOCAL COMMITTEE.-Mayor L. O&apos;Connor, Chairman; S. Fournier, Secretary; A. H. Beath, W. J. Bell, F. B. Bennett, D. M. Brodie, J. S. Buchanan, F. C. Busby, Wm. Chalmers, R. Dorsett, W. A. Evans, John Frawley, J. S. Gill, A. B. Gordon, J. G. Henry, T. N. Kilpatrick, Major Leckie, Chas. McCrea, John McLeod, Wm. McVittie, R. Martin, R. S. Mitchell, J. H. Morin, J. A. Orr, James Purvis (President Board of Trade), C. R. Reid, Major Smith, W. W. Stull, J. F. Templeton, S. E. Wright. The first session, held in the Banquet Hall of the King Edward Hotel, was called to order Tuesday, July 23, 1907, at 2.30 p.m., President John Hays Hammond presiding. Prof. Willett G. Miller, chairman of the General Committee, introduced Alderman J. J. Graham, who, in behalf of the City of Toronto, extended a hearty welcome to the members and guests of the Institute. To this welcome, President Hammond replied in a few well-chosen and hearty remarks. In the hall in which the session was held there was exhibited a fine, full-length, life-size portrait of Dr. Rossiter W. Raymond, in 1871 Vice-President and acting President, in 1872, 1873 and 1874 the elected President, in 1876 and 1877 Vice-President, in 1883, by appointment of the Council, and for the last 24 years by annual election, Secretary, of the Institute. Dr. James Douglas, of New York, N. Y., on behalf of numer-

Sep 1, 1907

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \&apos;r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or&apos; ?. ~eries deGcribi 1{) t:;&apos;~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,&apos;Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper &apos;Ii 11 be i acuss d c .icilY rub"col&apos;-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"&apos;e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

THE 125th meeting of the Institute was held in New York, Feb. 20-23, 1922, inclusive, and was the most successful annual meeting of the Institute ever held; there was a larger registration, there were more sessions of importance, and a greater number of sessions, than in any previous year. The total registration was 1331, comprising 351 New York members, 393 visiting members and 587 guests. At the annual business meeting of the Institute, held on Tuesday, Feb. 21, with President Ludlow presiding, there was a much larger attendance than usual. The report of the tellers was read and the following officers were declared elected: Arthur S. Dwight, Director and President-District 0 J. V. W. Reynders, Director and Vice-president-District 0 A. R. Ledoux, Director and Vice-president-District 0 Charles F. Rand. Director-District 0 George D. Barron, Director-District 0 William H. Bassett, Director-District 1 Thomas B. Stearns, Director-District 8 William Kelly, Director-District 5

Jan 3, 1922

By Rick Coleman

PT Freeport Indonesia’s (PTFI) latest expansion has increased total mill throughput to 125kt/d (137,700 stpd). The most recent expansion included the installation of a semiautogenous mill (SAG) designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation, including conventional and column cells, and a regrind circuit. All equipment is supported by a modern distributed control system. PTFI’s operations are located in the Ertsberg mining district of Irian Jaya’s Jayawijaya Mountains, the eastern-most province of the republic of Indonesia on the Island of New Guinea. PTFI, the operator, is owned by Freeport McMoRan Copper and Gold (81.3%), the government of Indonesia (9.4%) and private Indonesian investors (9.3%).

Jan 1, 1996

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.&apos;-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.&apos; In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \&apos;r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or&apos; ?. ~eries deGcribi 1{) t:;&apos;~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,&apos;Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper &apos;Ii 11 be i acuss d c .icilY rub"col&apos;-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"&apos;e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941