Search Documents

By Y. H. Zhang

Mechanism of BK501 in desiliconization from bauxite was studied by use of flotation test, EDS, ?-potential, FTIR. Results of flotation show that almost all of diaspore can be depressed when BK501 is put into pulp ranging from pH 4~12, in the meanwhile kaolinite is slightly activated. In the light of surface analyses, it is concluded that the adsorption of reagent on the diaspore is dominant by chemical interaction. Moreover, kaolinite may float more by addition of BK501 because of flocculation.

Jan 1, 2014

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrates identified gold to be mainly present in the form of a solid solution in pyrite. Gold distribution resulted in a poor extraction yield of 55 % by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction and has led to a gold extraction yield of 94%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and used a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a diaphragm-less electrolysis cell. The extracted gold was recovered via adsorption over silica and the gold depleted brine was treated for impurities removal. This brine was recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Shannon Studden, Angela King, Allan Koski

Cliffs Natural Resources is an international mining and natural resources company with over 160 years of history. A member of the S&P 500 Index, the company is a major global iron ore producer and a significant producer of metallurgical coal. Throughout its history, employees have been the foundation of the company’s success, which has long embraced a focus on continuous business improvement.

Jan 1, 2014

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By X. L. Wang

Hydrothermal method was applied in the preparation of calcium sulfate whiskers in airtight re-actor using gypsum as primary materials. The optimum conditions of preparation are as follows: pH value 9.8~10.1, concentration 5%, material size 18.1µm, which were determined by the analysis of the diameter of CaSO4 whiskers through SEM. On these conditions a product of ultrafine CaSO4 whiskers with diameter of 0.19µm and aspect ratio of 98 is obtained. Ultrafine CaSO4 whiskers with different concentrations, modified by titanate NDZ-401, were added into polypropylene as intensifier and composites of Ultrafine CaSO4 whiskers/ polypropylene were prepared by melting-extruding method. Mechanical performance of the composites was tested and surface morphology of the composites was observed by SEM. The results indicated that impact notched izod of the composites was enhanced by 49.5% compared with pure polypropylene when 10.0% Ultrafine CaSO4 whiskers were added into polypropylene and toughening effect was very remarkable. Dispersion behaviour and interface phenomenon of Ultrafine CaSO4 whiskers in polypropylene matrix were investigated by SEM. The results indicated that Dispersion performance of Ultrafine CaSO4 whiskers modified by titanate NDZ-401 in polypropylene matrix is good, which improved mechanical performance of composites to some extent.

Jan 1, 2014

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By M. Weir, J. R. Cutland, L A. J. Pronk van Hoogeveen

"A computer system for the design of open pits to mine stratiform orebodies has been developed for use at Nchanga Consolidated Copper Mines, Ltd. The particular requirements of such a system, for example, the accuracy of representation of geological detail and the ability to follow footwalls, arc described in this paper, together with the methods that have been adopted to satisfy them.A modified version of the Open Pit Design Program of Rio Tinto Zinc Consultants, Ltd. is incorporated in the system and the geological data are converted into a form usable by the computer by means of a pencil follower. Some of the uses which have been made of the system are described, with reference to the long- and medium-term planning of the Nchanga Open Pit, the major producing pit at Chingola Division."

Jan 1, 2014

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By K. Tsuchihashi, A. Kishimoto, T. Uda, Y. Kado, S. Maruyama

We recently proposed a continuous production process for titanium metal with some experimental results. In the process, titanium tetrachloride is reduced by Mg in the presences of Bi to form a Bi-Ti alloy at 900ºC. At this temperature, the obtained alloy is liquid and allows for the continuous removal of product and heat from the reaction vessel. The obtained Bi-Ti alloy was vacuum-distilled at 1000ºC for 24 hr, and 98 at % (92 wt %) titanium, which was easily crashed to powder, was obtained. Bi solvent was selected because of the highest titanium solubility at 900ºC and the moderate vapor pressure among the candidate metals (Bi, Sn, Pb, Zn, and Sb).

Jan 1, 2014

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014