Search Documents

By A. Schönecker, P. Y. Pichon, B. Kraaijveld, Y. Meteleva-Fischer

"Ribbon-growth-on-substrate is a casting method, which offers a possibility to control heat flow, nucleation and subsequent crystal growth at the liquid-substrate interface. This technology allows for low-cost and high throughput shaping of silicon sheets with controlled crystal grain size and orientation for use in solar cells. In this work, sheets of silicon- metal silicide composite materials were produced and their microstructure was studied. It was shown that depending on the relevant phase diagram and casting conditions, a micro/nano-sized eutectic structure of the casted sheet can be formed. Such composite materials possess properties promising for various applications in energy generation, storage and conservation. The advantages, potential and challenges of the ribbon-growth-on-substrate technique for production of composite sheet materials as well as novel areas of application for such materials are discussed.IntroductionThe Ribbon Growth on Substrates (RGS) process is well known in the solar industry as a process to produce multicrystalline silicon wafers. An industrial size pilot production line for continuous casting of silicon wafer was developed by RGS Development B.V. in the Netherlands (Figure 1). A comprehensive review of this technology and properties of the produced silicon wafers were reported by Schönecker et al [1]. The principle of the RGS process is explained in Figure 2. The relatively cold substrate extracts the crystallization heat from the liquid silicon in the casting frame. This results in the growth of a silicon ribbon (Vc) in contact with the substrate. When the substrate (Vp) is transported from the casting zone into the cooling section, the crystal growth stops, the wafer can be removed and the substrate can be re-used. Last few years large work was done on the industrialization and market development of RGS wafers for the solar industry. Part of this work was discussed by Schönecker et al [2]. Although there is still a good perspective on the middle and long term solar market for the RGS wafers, the current market situation was found to be unfavorable for new entrants."

Jan 1, 2014

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By O. C. Gaspar

The mineralogical and textural characteristics of the volcanogenic massive sulphide ores from the Aljustrel and Neves-Corvo deposits have been studied by ore microscopy techniques since 1977. Several ore types have been recognized, and the ore paragenesis, ore textures, and behaviours of different ore types during grinding and concentration processes, have been determined. An ore classification was established for use in metallogenetic studies, ore reserve calculations, selectivity during mining, and control of the ore beneficiation processes. In addition, an empirical method was developed for supplying, on time, the qualitative and semi-quantitative information needed for processing the Aljustrel ores and for optimizing the Neves-. Corvo copper and tin concentrators.

Jan 1, 1991

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By Markku Rytkonen, Shaolong Chen, Ilpo Kylmäkorpi, Hannu Mansikkaviita

Though the Peirce Smith (P-S) converter is a traditional type of furnace, continuous improvement in its mechanical and electrical design is still Kumera's approach. Efforts are made particularly on the following aspects: converter head shape for easy fabrication and structural strengthening, oxidation air swivel joint for low pressure drop and low noise level, wind box for even air distribution to tuyeres, drive unit and its control for reliable and handy operation. These improvements have successfully been applied in recent P-S converter deliveries.

Jan 1, 2009

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By Ailton S. Ferreira, Rubén J. Sanchez Rodriguez, Sergio N. Monteiro, Felipe Perissé D. Lopes, Teresa E. Castillo

"Polyester composites reinforced with natural lignocellulosic fibers have, in recent times, been gaining attention in engineering areas as lighter and cheaper alternatives for traditional composites such as the ""fiberglass"". One of the strongest, the curaua fiber, is today being considered as reinforcement of composites for automobile interior parts. In fact, several research works are currently being dedicated to curaua fiber composites since physical and mechanical properties are required for practical uses. In this work, the thermal behavior of polyester composites reinforced with up to 30 % in volume of curaua fibers was investigated by differential scanning calorimetry, DSC. The results showed endothermic and exothermic events associated with water release and possible molecular chain amorphous transformation. Comparison with similar composites permitted to propose mechanism that explains this DSC thermal behavior.IntroductionThe modem composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace [1]. In fact, fiber composites offer significant advantages over monolitic materials, such as common metallic alloys, plastic and ceramics. One of the most important is the ratio between the ultimate stress and the density, known as the specific strength. For example, in common glass fiber polymer composites, the so called ""fiberglass'', the specific strength of around 400 MPa.cm3/g is higher than any conventional monolitic material. However, drawbacks exist. The energy required to fabricate ""fiberglass"" generates large emissions of C02, which are responsible for global warming. Moreover, ""fiberglass"" is not recyclable and cannot be incinerated [2]. As a result, most synthetic fiber composites end up in landfills or contribute to rivers and oceans pollution."

Jan 1, 2011

By O. Norman Lotter

The formulation and use of mixed collector suites in sulphide flotation can be traced back as far as 1957 with the work of Glembottskii and his co-workers in Moscow. The subject was reviewed by Lotter and Bradshaw in 2010, and proposed a synergy between ideally-selected different reagent types to deliver improved performance, in particular the in situ catalysis of a xanthate to dixanthogen by a dithiocarbamate. Correctly formulated for a particular application, an optimally arranged mixed collector suite delivers the following improvements to the flotation process: • An increase in the flotation kinetics • Improvement in coarse, or middling, particle recovery • Reduction in total dosage requirement • Best results are found from testing the ratios of the collectors. This is of critical importance. In all an optimally formulated mixed collector system usually delivers an increase in paymetals recovery of 1–4% absolute, with a gain in concentrate grade in the range 10–20% relative. In recent years, the addition of semi-conductor theory and associated electrochemistry has contributed significantly to this toolbox by way of identifying optimum domains of Eh and pH for the flotation of individual minerals. In the case of mixtures of minerals, this is where the mixed collector system delivers significant value by way of presenting a mixed set of collector radicals and dimers in a common Eh and pH domain for overall performance. This calls on a fundamental understanding of organic chemistry, mineralogy, semiconductor theory, and electrochemistry. Whereas the selection of grinding media type effectively influences the Eh, the pH can be easily controlled by pH modifiers. The theory of this system, and some industrial case studies, are discussed.

By John H. Schloen

Copper refineries are constantly looking for methods to upgrade their plants to reduce refining costs and to improve the purity of their electrolytic cathodes at the same time that the purity of the anodes they refine is being lowered by the rehabilitation of reverberatory furnace smelters to one of the direct smelting processes. The comments given below are based on the answers to the questionnaire returned bf the 36 copper refineries that represent 66% of the western world s refining capacity. Eleven refineries employ some form of uniform weight anade casting, e.g., Outokumpu, Contilanode, Mitsubishi, Lurgi, or Hazelett. This type of anode casting presents the best possibility for improving cathode purity. The cathode press of Phelps Dadge can improve current efficiencies and cathode quality. The press is used on first-run cathodes, after 48-60 hours, on half-cells at a time without interruption of the cell current. One refinery interrupts current for sever.al hours to allow the anode slime to settle before the, cathode pressing. The cathode press is now used at eight refineries. Apart from periodic reverse current (PRC), it is not expected that current densities will be increased. Thirty refineries, using direct current, average 231 amps/M, with a low of 178 and a high of 350. Five refineries use PRC at an average of 338 amps/M, with a low of 290 and a high of 380. Current efficiencies are good at an average of 94%, with a low of 88% and a high of 99% for the 34 refineries that reported. It must be remembered that the cycle efficiency with PRC is about 93%., so that the effective current efficiency with PRC would be only .94 X .93 or 87% However, PRC should be considered seriously for refinery expansions because it can save about 25% on capital costs.

Jan 1, 1987

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015

By K. D. Mondale

The chemical and physical properties of samples from ten sedimentary zeolite deposits. (representing chabazite, clinoptilolite, erionite and mordenite types), have been determined as a prelude to the development of a wet beneficiation process. The mineralogical composition of each deposit and such properties as morphology, size, apparent density, surface area, pore volume, relative hardness and zeta potential in solution have been determined. Some of these properties, especially apparent density and relative hardness, were found to differ significantly from textbook values. Based on differences in properties between the zeolites and their associated gangue minerals, a wet beneficiation process has been developed which makes use of selective grinding, sizing, sorting and gravity concentration. Additionally, an alternative upgrading process using flotation has been developed for one of the deposits.

Jan 1, 1988

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

By Norman Schapiro

Future ore bodies will, most likely, be more costly to find, mine and process than those now in production because most of them will be of lower grade or found deeper. To evaluate an ore deposit for extraction of metal values it is important to select the optimum economic process from among the many available options. The physical and chemical behavior of the minerals present should govern the process selection. Process mineralogy which combines mineralogy and petrography with process development engineering generates the data on mineralogy, composition and texture of gangue and valuable minerals from which the optimum process steps can be selected in the commercial design of the ore processing plant. These insights also help in solving operating problems caused by changes in the ore body

Jan 1, 1981

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

By Hebi Yin

A coupled cellular automaton (CA) - finite element (FE) model was developed to calculate the growth of dendrites during the solidification of cubic and hexagonal metals. The model solves the conservation equations of mass, energy and solutes in order to calculate the temperature field, solute concentration and the growth morphology of dendrites, including the grain structure and the dendritic microstructure. Validation of the model was performed by comparing the simulation results with calculation results from previously published works, showing qualitatively good agreement in the dendritic morphology. Application to magnesium alloy AZ91 illustrates the difficulty of modeling dendrite growth in hexagonal systems, observed as deviations in growth direction caused by mesh-induced anisotropy. The model was applied to the simulation of small specimens with single- and multiple- equiaxed grain growths and columnar grain growth in directional solidification. The influence of cooling rate and some kinetics parameters on the grain morphology are also discussed.

Jan 1, 2009

By John R. FitzPatrick

The separation and purification of uranium from either nitric acid or hydrochloric acid media tan be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated' to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps. We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (100-gram) flow experiments using depleted uranium, were done after the small-scale evaluation Of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments' involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and' amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process. Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail.

Jan 1, 1996

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By David T. Hobbs

Large quantities of highly alkaline, radioactive, liquid wastes are stored in underground tanks throughout the Department of Energy complex. These wastes will be pretreated to separate radionuclides and the remaining decontaminated liquid wastes incorporated into solid waste forms for permanent disposal. Significant savings in disposal costs could result by recovering .the sodium as sodium hydroxide for reuse or disposal as nonradioactive waste. Recent testing demonstrated an electrochemical separation process for the recovery of sodium hydroxide from alkaline waste solutions; The separation process uses ion-selective membranes to separate sodium from the bulk of the waste constituents under an applied electrical field. The sodium is recovered as a 10-15 wt % solution of sodium hydroxide. Results of bench-sc3Ie and pilot-scale tests with simulated and radioactive waste solutions are presented.

Jan 1, 1999

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999