Search Documents

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4T13O12 (BIT) which has a positive temperature coefficient of dielectric constant (TE) can be used to modify the negative of typical microwave dielectric ceramic BaNd2Ti4O12(BMT). However, BaNd2Ti4O12/Bi4Ti3O12/BaNd1Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C was much higher than that of Bi4Ti3O12 ceramic (around /1100°C). in this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated divided proposed to prepare ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second mop, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti1O12 ceramic pellets and spark plasma sintered at 900'C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe mircoanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/B1T/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.8, a low dielectric loss of 0.0068 and a small temperature coefficient of dielectric constant v/35 ppm/C at 1 MHz.

Jan 1, 2003

By Uchil Jayagopal, M. Krishna, P .. V. Krilpakara, S. Manjunath

"There have been a pioneering efforts over the last forty years in the development of metal matrix composites (MMCs) as a new engineering materials, having improved properties, light weight characteristics and competitive costs compared to traditional materials. Following recent advancements in casting technology and the use of melt stirring device by foundries, discontinuously reinforced MMCs where prominent alloys are reinforced with particulates or short fibres and the being employed ·in the production of castings targeted for automotive and aerospace application.The ZA-27 alloy has a high strength compared to zinc or alluminium alloys with a lower melting temperature. The main objective of the present research is to study the effect of quartz particles on the mechanical behaviour of ZA-27 alloy composites. The results showed that the ultimate tensile strength, hardness, Young's modulus of the composite gradually increased with increase in the weight percentage of the quartz reinforcement. However overall ductility decreased with an increase in quartz reinforcementIntroductionMetal matrix composite (MMCs) offer outstanding benefits as they combine metallic properties with ceramic properties there by yielding improved physical and mechanical properties.1Among the various type of MMCs particulate reinforced composite are the most versatile and economical2. By suitable choice of metal matrix and particulate system a wide range of properties combination can be obtained such as strength, modulus, fiiction.al resistance, tribological performance and machinability. These composites are capable of replacing conventional alloys in a considerable range of applications. They also offer significant saving in energy and resources"

Jan 1, 2000

By E. N. Mounsey

The paper addresses the design of the Zhong Tiao Shan Company (ZTS) Houma Ausmelt Technology copper smelter in People's Republic of China. The smelter represents the third copper smelter development using Ausmelt Technology, the first large scale (35,000 tpy blister copper) and the first smelter to use the Ausmelt Technology smelting and converting process steps in separate TSL vessels in a continuously operated process. The project will be realised through the combined efforts of ZTS, Ausmelt and ENFI, the Beijing Non-Ferrous Engineering Institute who provided partial detail engineering services in China. Ausmelt will provide the technology licence, basic and detailed furnace engineering packages and additional technical services including cold commissioning support and hot commissioning supervision.

Jan 1, 1999

By R. Singh, C. Gong, J. Chaudhry

"Metalorganic chemical vapor deposition (MOCVD) is an ideal technique for the deposition of conducting and non-conducting oxide based thin film materials. In this paper we have presented a study of photo assisted MOCVD for the low temperature deposition of a number of oxide based advanced materials. We have used incoherent light sources as the source of optical and thermal energy in our MOCVD system. The vacuum ultraviolet (VUV) and ultraviolet (UV) photons can enhance the surface reaction of the absorbed molecules through the perturbation of the electronic state of binding between the absorbed molecules and the solid surface. Unlike plasma process, no surface damage is expected and high quality materials have been deposited. At a given substrate temperature, the performance of deposited film depends on the lamp configuration.INTRODUCTIONMetalorganic chemical vapor deposition (MOCVD) has become the standard manufacturing technique for the deposition of large area thin films of compound semiconductors. l.(.w-cost, high crystalline quality, atomically clean and sharp interfaces, atomic layer epitaxy, high throughput rates and potential for direct writing are some attractive features of MOCVD. Due to a number of potential advantages mentioned above, MOCVD is considered as an ideal technique for the deposition of various electronic and optical materials for a wide variety of applications. Rapid isothermal processing based on incoherent radiation as the source of optical and thermal energy is emerging as the key low thermal budget (integral of processing time and temperature) processing technique for the fabrication of current and next generation of microelectronic and optoelectronic devices and circuits [1]. In this paper we have demonstrated that the design of the lamp assembly plays an important role in determining the properties of the materials deposited by RIP assisted MOCVD. We have studied the growth rates, structural properties and electrical properties of Y2O3/Si structure. At a given substrate temperature, best results are obtained for the lamp assembly that provides maximum number of VUV and UV photons."

Jan 1, 1994

By M. Furuta, M. Hasimoto, Y. Komoda, K. Haiki

"Tamano Smelter & Refinery started its operation in 1972 with high current density electrolysis (350Nm2 of maximum) applying PRC technology. After the start up, four times of expansion have been done, the cathode production capacity has increased from- 84,000 t/y to 191,000 t/y. However, recent refining technology with permanent stainless steel cathode enabled to increase current density up to 300 Nm2 or more without PRC method. In order to increase current density more than 350 A/m2 , experimental work using commercial size cell has been carried out at several conditions, such as current density, PRC conditions, electrolyte composition and electrode condition. As a result, it was found that high quality (LME A grade) cathode can be produced at such a high current density as 405 A/m2•IntroductionWhen considering the production increase of electrolytic copper, what becomes important is the improvement of productivity per unit of production facility. Conventionally, production had been expanded by increasing the number of cells but a huge investment required for this had a influence to the business profitability. Because of this, increase of current density, which is one of the methods to improve unit productivity, 'was expected and this method at the same time has another advantage of shortening the retention time of copper and other precious metals in the cells. At present, the average current density at Tamano during full capacity production is around 350 A/m2 and this used to be the limit throughout the world (1)."

Jan 1, 2000

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste- free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203' Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By Gjergj Dodbiba, Atsushi Shibayama, Toyohisa Fujita, Takashi Shikazumi, Yukio Kato, Kenji Murata

"A new crushing or liberation technique by means of underwater explosion is put forward. This technique is suitable for crushing and liberating various materials, for instance: the electric parts of the discarded portable telephone, CPU from mother-boards of PCs, steel from plastics tubes used as construction materials, waste constructed materials like panels, tungsten carbide scraps, as well as slitting the optical disk (e.g. DVDs), etc. The materials to be crushed are immersed in water and then the explosion is carried out by using only a small amount of explosive. The shock waves in combination with the generated bubbles are very effective in liberating the materials of different densities. It was observed that the metals crushed or liberated by using this technique were leached much faster when compared with the conventional crushing technique. This crushing method can be applied for liberation of many kinds of electric or mechanical tools. Introduction The explosive has been used since Nobel’s invention in 1866. The main practical application of explosion is in the large scale public works, such as dam construction, land development, tunnel, mining and dismantlement of building. The shock wave caused by explosion extremely can generate high pressure able to break the concrete and rock, and other materials. In this study, the crushing and liberation of waste materials was carried out by explosion in water. The idea was to use this technique as a pretreatment stage prior to recycling. The explosion in water can be used to crush hard materials, helping the liberation between different attached materials. The samples used in this experimental work are waste materials such as construction materials, hose, cemented carbide, cellular phone, lithium buttery, DVD-R, etc."

Jan 1, 2008

By T. H. Jeffers

The U.S. Bureau of Mines' Salt Lake City Research Center. has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants? from wastewater&. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high .affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics . and can be used in conventional processing equipment or low-maintenance systems.. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine wastewater& using B'IO"FIX beads. Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NDIJS) after 175 loading-elution cycles, Adsorbed metals were removed from the beads using dilute ?mineral .acids. In many cases" the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge. Tests indicated that use of the beads in a low-maintenance system was particularly effective for treating remote acid mine drainage waters? and small toxic seeps from hardrock mining districts ..

Jan 1, 1991

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By S. Gopalan, J. D. Milshtein, S. N. Basu

Production of syngas is proposed utilizing the W/W03 redox system and employing a solarpowered two-step thermochemical cycle. Three chemical reactions occur in two chambers. Assisted by a solar concentrator, a high temperature reaction reduces W03 powder to metallic tungsten in both chambers. Subsequently, the temperature in one of the chambers is lowered and H2(g) is produced via re-oxidation of the tungsten powder using steam. The temperature in the other chamber is simultaneously lowered to an intermediate temperature and CO(g) is produced via oxidation of the tungsten powder using C02(g)· The gas streams coming out of the two chambers result in the syngas production. A complete thermodynamic analysis of the system is described. The W/W03 redox cycle offers greater gravimetric fuel productivity compared to previously proposed systems, and the entire cycle can be operated below 1273K.

Jan 1, 2013

By R. H. Hanewald

The INMETCO process has been modified so as to recover nickel. chromium and Iron from a wide variety of metal containing waste-streams. This now includes the recovery of metals from spent acid solutions such as chromic acid etching I1quids. nJcke1 and chromium plating solutions; stainless and superalloy pickling solutions. etc. In addition. hazardous electric furnace stainless steel and. superalloy baghouse bags can be processed so as to recover the valuable metall1cs. A detailed review of the above new recovery techniques w1ll be discussed as well as the current operating methods used at INMETCO.

Jan 1, 1992

By Ricardo A. Valls

The Sechol Nickel-Cobalt Laterite Project is located in East-Central Guatemala, 140 km northeast from Guatemala City. In-situ resources in the immediate Sechol area, including those on other mining concessions contain 133 million tonnes of mineralization, grading 1.5 1% nickel. Considering the ever-increasing market for these metals, and the potential quick return on the initial investment, Jaguar Nickel Inc. is confident that by late 2006, it will be producing the first nickeltcobalt hydroxides from Guatemala. The path from now until the production stage passes through a pre-feasibility study, scheduled for completion by mid 2004, and bankable feasibility by mid 2005. Jaguar's objective, however, is not only to have a producing nickel-cobalt mine by late 2006, but also to continue with the exploration work in order to make Guatemala one of the world's leading nickel-cobalt producers. The Sechol group of deposits is conformed of several lateritic pockets, delimited by tectonic faults, and hosted by ultramafic rocks of the Sierra de Santa CW. ophiolitic belt that intruded the Maya Continental Block during the Early Tertiary age. The intrusive is mainly represented by a layered sequence of dunites, peridotites, and pyroxenites, usually strongly serpentinized. Existing data indicate that these rocks underwent fractional crystallization, and probably some degree of magma mixing and contamination previous to their main tectonic event. The most complete profiles are usually present over weathered dunites and serpentinites, while on top of the less altered pyroxenites, there is usually the formation of only a limonitic zone. The relative complexity of the ophiolitic belt explains the variety of mineral resources in the area, which include Ni-Co-Fe laterite, chromite, bauxite, magnesia, and also has the potential for gold, PGMs, and precious and semi-precious stones such as jade, nephrite, and chrysoprase. Metal recovery from the Sechol deposit will be based on an atmospheric chloride process, followed by solution purification, production of an intermediate nickellcobalt hydroxide suitable for sale, and finally acid and magnesia recovery by standard spray roasting technology. The chloride process will allow exploitation of the whole lateritic profile to produce 20,000 Mt of nickel hydroxide and 800 Mt of cobalt hydroxide per year. The exploration work completed to date has concentrated mostly on the Sechol group of deposits, representing less than 5% of the current land position of Jaguar in Guatemala. Within Sechol, the company has identified a large pocket of more than 5 Mt of laterites grading 2.1% nickel and 0.08 % cobalt as a startup pit "El Inicio". Including the work previously completed Keywords: Laterite deposits, Ophiolitic Belts, Central Guatemala, Nickel, Cobalt

Jan 1, 2004

By R. W. Harnmack

Hydrogen sulfide generated by the anaerobic respiration of sulfate-reducing bacteria was used to treat pH 2.2 water from the abandoned Rio Tinto copper mine in Nevada. The untreated water contained 550 mg/L Fe, 140 mg/L Al, 90 mg/L Cu, 80 mg/L Mn, 60 mg/L Zn, 4 mg/L Co, and 2 mg/L Ni. The bench-scale treatment system examined consisted of a bioreactor for H2S generation and three precipitator/clarifier units for metal sulfide precipitation and recovery. The treatment system reduced the concentrations of all metals except Mn to less than 0.1 mg/L. Manganese concentrations were reduced by 96 percent to 3.3 mg/L. A CUS/SO concentrate (33 pct Cu) and a ZnS/5° concentrate (28 pct Zn) were produced that may be suitable for metal recovery at existing smelters

Jan 1, 1994

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003