Search Documents

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Chris Mark

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends, If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the "full resistance zone" of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. This paper describes recent studies using short encapsulation pull tests in the U.S. Tests were conducted in the National Institute for Occupational Safety and Health (NIOSH) Safety Research Coal Mine at Bruceton and at underground mines in Pennsylvania and West Virginia. The study found that the SEPT can be used to make a simple evaluation of resin bolt anchorage. Suggested procedures for conducting SEPT are included. The study also confirmed that poor anchorage can be an issue, particularly where the roof rock is very weak. Some simple techniques for improving anchorage, and thereby the effectiveness of fully grouted bolts, are discussed.

Jan 1, 2002

By Christopher Phillips

In light of recent events in the mining industry, there has been an increasing demand for technology to detect underground voids and abandoned mine workings. This paper summarizes the use of geophysical methods for this application. Geophysical methods have been successfully employed in the detection of underground voids in several disciplines, including foundation analysis, road and infrastructure analysis, and darn analysis, but is not yet being widely employed by the mining industry. The principal reasons are that the combination of the complex geological setting of a mine, mine design, surface conditions, and improper choice of geophysical method often makes the task of locating abandoned mine workings with geophysics a frustrating, time consuming, and often unsuccessful venture. While there are several geophysical methods that have been demonstrated for the successful detection of abandoned mine workings, there is still no 'silver bullet' to solve the problem in every case. The choice of geophysical method to detect abandoned mine workings should be made on a site specific, and sometimes target specific, level. This paper reviews current methods, and introduces recently developed methods, for the detection of underground voids and abandoned mine workings.

Jan 1, 2003

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Leo Gilbride

Western U.S. longwall operators face increasing challenges with optimizing ground control and productivity as mines reach greater depths and coal bursting hazards increase. Some western U.S. mines, many known to be bump-prone, achieved a successful balance between ground control and productivity by transitioning to side-by-side longwall panel mining combined with a yield pillar gateroad system. With this design, development footages could be minimized and pillar bumping averted by controlled yielding at moderate depths, generally in the range of 450 to 600 m. Over the past four decades, the yield pillar system has won wide acceptance among western mines facing pillar bursting hazards, particularly those in the Wasatch Plateau and Book Cliff coal fields of central Utah. However, recent attempts among the deepest Utah operators to mine side¬by-side panels with yield pillars at depths in excess of 600 m have been met with mixed success and, in some circumstances, with serious difficulty. Challenges include violent face bursting and excessive tailgate convergence outby the face, which can be crippling to ventilation. The use of interpanel barriers, i.e., barriers left between longwall panels, offers one possible solution to mining under deep cover with bump-prone geology. Interpanel barriers have already been adopted by Utah's deepest longwall mine, and others are considering their use. The geomechanical implications of mining with and without interpanel barriers, and the competing tradeoffs between ground control and ventilation are discussed.

Jan 1, 2004

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By John Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a mine slope entry, the problem becomes more complicated because a slope transverses through many different types of strata. Mine slope ground control has traditionally been practiced based on trial and error and prior experience. There is currently no well-accepted slope and support design methodology available for an economical and technically sound ground control plan. Over the last few years, Keystone Mining Services, LLC (KMS), the engineering affiliate company of Jennmar Cooperation, has developed a ground support design methodology called the ?Stress, Geologic, and Support design system? (SGSSM). This patent pending method enables accurate analysis of actual geo-technical conditions and stress; identifies strong, fair, and weak sections along the slope; formulates primary and supplemental roof bolting systems, designs optimal long-term steel structure support; and verifies the adequacy of the developed support. The method has been successfully utilized on various new slope projects and has been well received by state and federal regulatory agencies during the approval process. This paper details the concepts of the methodology using an actual case study of a slope project in the Midwest.

Jan 1, 2011

By Stephen C. Tadolini

A joint research program was designed and conducted at Lodestar Energy?s Baker Mine to investigate the performance of a high-capacity tensioned cable supported gateroad. The secondary system consisted of a 4.5 m (14.5 ft) 7 strand cables that were 23 mm (.9 in) and 18 mm (.? in) in diameter with a designed capacity of 515 kN (58 tons) and 355 kN (40 tons), respectively. The cables ware installed with an effective resin column length of 1.25 m (4 ft) and then pre-tensioned using a hydraulic jacking system. Roof separations, caving characteristics, and support performance was monitored and evaluated during the critical extraction of the adjacent panel, complex geological conditions of the west Kentucky No. 13 seam were mapped and the support performance recorded. This paper will describe the theory of tensioned cable systems and present an assessment of the support performance during the longwall retreat mining process.

Jan 1, 2000

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Terry Medhurst

Geophysical logging is routinely undertaken as part of most Australian coal mining exploration programs. Typically, the main application is the determination of coal seam depth and the qualitative estimation of coal quality, lithology and rock strength. For rock strength estimation, sonic transit times relate to the elastic properties of the rock and provide a general correlation with uniaxial compressive strength. However, experience has shown that site-specific relationships are necessary to account for different geological environments. In this paper we describe results from a series of recent studies that have provided a more comprehensive method of geotechnical strata characterisation using detailed lithological interpretation and rock property estimation from borehole logs. This has resulted in an improved method of estimating rock strength via the determination of the proportions of quartz and clay plus the porosity. We also propose a rock classification scheme based on geophysical log analysis. This builds on the existing acceptance of the sonic log as an indicator of rock strength and adds scores according to the moisture, cohesion, porosity and quartz content inferred from the geophysical logs. The new scheme can be related to existing mapping based schemes such as CMRR and the Q-system.

Jan 1, 2005

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

By Mark G. Colwell, Russell Frith

"An Analytical Model for Coal Mine Roof Reinforcement (AMCMRR) has been developed. AMCMRR utilizes a Factor of Safety (FOS) approach, which is commonly used in all forms of engineering. The starting point in the development of AMCMRR was an existing analytical roof behavior and roof support design methodology/model, originally developed by Colwell. This technique was used successfully in the Australian underground coal industry for roof support evaluation and design prior to and during the course of the research project, and when used, it was essentially calibrated on a site by site basis.It has long been recognized that bolts and longer tendons can modify the behavior and load bearing capacity of the reinforced roof via the concept of beam building. The break-through in developing AMCMRR was combining the original analytical model with a comprehensive database (associated with Australian collieries) to effectively quantify this reinforcing effect, and this in turn provided the ""platform"" by which this analytical model can be calibrated for the entire Australian underground coal industry.This paper focuses on the application and use of AMCMRR and the analyses undertaken to quantify the reinforcement beam building offers to the immediate roof. Furthermore, this paper demonstrates that a combined empirical and analytical approach is currently the most practical way of developing credible geotechnical design tools for the Australian or any other underground coal industry.BACKGROUNDBy the start of 2006 the ALTS (Analysis of Longwall Tailgate Serviceability-Colwell et al., 2003) and ADRS (Analysis and Design of Rib Support-Colwell, 2006) design methodologies were being routinely and widely used within the Australian underground coal industry. As a result of their success, Colwell Geotechnical Services commenced a research project entitled, ""The Future Development and Integration of ALTS & ADRS for Improved Underground Roadway Design. "" The project (which became known as the ALTS 2006 Project) was funded directly by several of the major coal producers as well as individual Australian collieries."

Jan 1, 2010

By Swapan Bhattacharya

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must 'adopt measures consistent with known technology in order to prevent subsidence causing material damage to the ex- tent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predict- able and controlled manner..." Implied in the constraints of Section 516 (b) (1 of SMCRA is a determination of what constitutes "material damage" to surface structures and renewable resource lands, and the capacity for sequential land use following underground mining. This Study was undertaken in an attempt to provide quantitative guidelines for estimating material damage to a wide variety of surface structures and renewable resource lands. Surface structures studied included buildings, bridges, railroads, highways. pipe- lines, d~, embankments, and water reservoirs. Damage criteria for buildings developed in this study along with details of the adopted methodology have been presented elsewhere (Bhattacharya et al.) (1). and will not be repeated here. Similar guidelines for renewable resource lands have also been discussed (Singh and Bhattacharya) (2)

Jan 1, 1984

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993