Search Documents

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Thomas M. Barczak

This report examines practical considerations in longwall support selection that have evolved from Bureau of Mines ground control research. The scope of discussion includes trends in support selection, analysis of shield designs, performance testing, and an examination of support and strata interaction theories and their relevance to in situ support loading. Application recommendations are made for two-leg shields. four-leg shields, and chock-shields. Two-leg shields account for 67 pct of the current active longwall installations and are used in a variety of applications. Automated control systems are likely to continue to grow in utilization. The next major change in shield design is likely to be the application of wider supports. The most effective method of performance testing longwall shields is by controlled displacement of the canopy relative to the base. Controlled force application does not control the load transfer through the shield and may not produce maximum loading in all support components. Theories of estimating support capacity based upon a detached roof block that must be maintained in equilibrium by the powered support are being challenged by concepts based upon the equivalent stiffness of the total ground supporting system.

Jan 1, 1990

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By Yi Luo

Multiple-seam mining operations induce surface subsidence basins different from those caused by mining in a single coal seam, and also disturb the mining operations in the other coal seams. A computer program, CISPM-MS (Comprehensive and Integrated Subsidence Prediction Model for Multiple Seam Mining), has been developed to predict the final surface movements and deformations as well as the interactions associated with multi-seam coal mining operations. The program applies a newly developed subsurface subsidence prediction model that is able to consider the geological stratification variations. In predicting surface subsidence, the surface movements and deformations caused by the individual mining operations as well as the interactive effects are all considered. A case study is conducted in this paper for validating the program.

Jan 1, 2012

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By Dave Minney

The South African mines health and safety regulations require that mine management establish a quality management system for rock support material. Quality control of resin capsules used as a support medium in South Africa is specified under SA National Standards No 1534. Experience has shown that this specification, while addressing the chemical and physical aspects of the products, but does not address the required performance criteria. In order to address this shortcoming, the industry has put a lot of emphasis on short encapsulation pull tests, performed insitu, in the underground workings of the mine. This is also fraught with many shortcomings, particularly as regards site availability, cost and repeatability of results. To try and address these issues, the Department of Mechanical and Aeronautical Engineering at Pretoria University were approached to develop equipment and machinery that could produce reliable, repeatable results in a laboratory environment which reasonably simulates installation practice underground. The test method is based on the ASTM F432-95 Strength Index test, but modified to use push test rather than pull tests. The paper describes development of the test method and the preliminary results and findings of the work.

Jan 1, 2007

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By Sandin E. Phillipson

The Mine Safety and Health Administration?s Roof Control Division responded to a massive ground failure at an underground marble mine in northern Georgia. The ground failure occurred in a benched area that had been abandoned in the early 1990s. It involved the failure of an estimated 19 pillars, in conjunction with a massive roof fall of an undetermined extent that was at least 60 ft high. Pillars in the benched area had been mined nominally 40 x 40 feet to a height of 50 feet ft, with 40-ft mining widths, although it seems likely from measurements and accounts from mining personnel that pillars were even smaller than intended. Average overburden depth was 500 ft, and the rock mass was characterized by three sets of intersecting geological discontinuities that not only defined very blocky conditions that were conducive to pillar spalling and volume loss, but they were also adversely oriented in such a way as to cut diagonally through pillars at a high angle. The recently released S-Pillar software from NIOSH was used to determine pillar safety factors in the failure area and indicated that pillars were undersized for the conditions. S-Pillar was used to assess pillar stability in active areas to evaluate the likelihood of experiencing similar collapses in the future. S-Pillar correctly identified the pillars in the bench area as having been at risk for instability, in light of their ultimate failure. A two-dimensional finite element model was used to evaluate the possible stages of failure and to assess the likelihood of continued failure in the benched area that might affect more distal mine openings. Although stone mines are generally characterized as having more forgiving conditions than those found in softer sedimentary rocks, the failure shares some characteristics with domino-style massive pillar collapses experienced in coal and trona mines. First, the minimum dimension of the benched area approached 350 ft; second, the pillars defined by benching had small width-to-height ratios (0.8), and; third, the pillar failure area was slightly greater than 4 acres. The massive pillar collapse and associated roof fall illustrate the importance of incorporating pillars that have been properly sized for depth and for the final bench height. Furthermore, the designed dimensions must be adhered to during the actual mining process. Finally, the importance of understanding the geological conditions and their effect on the rock mass is critical.

Jan 1, 2012

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006