Search Documents

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By M. E. Hinkle

Concentrations of He, CO2, and O2 in soil gases were measured regularly for more than a year at a site near Golden, Colorado. Samples were collected from a hollow probe at 0.75-m depth and from a plastic hemisphere on the ground surface. Soil temperature, air temperature, percent humidity, And barometric pressure were also measured. Soil moisture was measured only indirectly as amount of rain or snowfall. Higher concentrations of CO2 in both the 0.75-m and surface samples correlated with higher soil and air temperatures, which suggests that CO2 was produced by bacteria. Lower concentrations of helium in both the 0.75-m and surface samples correlated with higher soil and air temperatures. Rain and snowfall appear to affect helium concentrations. Carbon dioxide concentrations were lowest when snow lay on the ground for extended periods of time. No correlation was seen between barometric pressure or percent humidity and concentrations of He, CO2, or O2 at 0.75-m depth or at the ground surface. No correlation, either positive or negative, was seen between concentrations of CO2 and O2.

Jan 1, 1988

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By A. S. Azman

In collaboration with Kennametal Inc. and corry rubber corporation, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a drill bit isolator to address noise overexposures associated with roof bolting machines in underground coal mines. NIOSH laboratory studies confirmed that the drill bit isolator reduces noise during drilling. Field studies were needed to confirm that a noise reduction could be obtained under working conditions and that the device was sufficiently durable. This paper reports results of field tests of the device conducted at five underground coal mines. Noise reduction was assessed by comparing the operator?s noise exposure during drilling with and without the drill bit isolator. Durability was assessed by recording the number of holes and total feet drilled with each bit isolator until either the test period ended or the device failed. The results from these tests showed that the device is an effective noise control in a mine environment. The field-tested drill bit isolators provided a noise reduction of 3-5 db(A). Of nine devices tested for durability, five exceeded 610 m (2,000 ft) drilled and two exceeded 762 m (2,500 ft) drilled before failure. Durability issues found in the field tests led to final production optimizations that have resulted in a commercially available product for drilling with 35-mm- (1.3-in.-) diameter roof bits and hexagonal drill steels.

Jan 1, 2012

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By K. R. Miller

In recent years, surface mine equipment operators in the Campbell County region of the Wyoming Powder River Basin have found new ways to solve old problems. This paper will examine overburden stripping equipment and techniques by focusing on evolving applications for draglines, shovels, and dozers.

Jan 1, 1998

By André Vervoort

After the systematic closure of Europe’s coalfields in the late twentieth century, the emphasis is now clearly on industry’s environmental legacy. One aspect of the latter is the longterm surface movement above abandoned coal mines. The analysis of satellite data shows that the subsidence lasts longer than generally assumed. However, a few years after the flooding of the abandoned underground coal mines, a new phenomenon was observed, i.e., the direction of the surface movement was reversed. The phase of upsidence has already lasted for several decades, and only future measurements will tell how long it continues. A key conclusion is that the regions with maximum subsidence do not necessarily correspond to the greatest upsidence. In other words, buildings and infrastructure are subjected to a different loading from this upsidence than during the subsidence phase. The longterm surface movements have an impact on vulnerable structures in the densely populated regions of the former deep coal mining areas in Europe. These movements create additional damage. This new knowledge is also relevant for mines that are still in operation or future mines that are planned.

Feb 1, 2024

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By J. Herbst, I. Heber-Panu, Dan G. Cojocariu, E. Ene-Danalache, G. Poling

A general model which represents not only batch but also continuous flotation in multi-cell machines is presented. This model considers both the size distribution and the distribution of flotabilities in a size class for valuable mineral particles in the pulp. The general expression is shown to reduce to several previously reported models. In addition, a number of new models are found to arise for different specific assumptions concerning the flotability distribution and/or the size distribution of the particles undergoing flotation. Several of these new models are tested experimentally using laboratory-scale batch and pilot-scale continuous data. Model parameters are estimated from this data and a comparison of calculated recoveries and those experimentally determined are presented. Finally, the influence of the feed rate, aeration rate and valuable mineral content of the feed on the recovery is examined.

Jan 1, 1976

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau's research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By D. H. Desy

This research was undertaken to establish the lncendivity of aluminum alloys against rusty steel under frictional impact conditions at typical coal mine fan speeds, to determine any differences in incendivity among various aluminum alloys, and to Investigate less incendive materials as substitutes for aluminum alloys. With a specially designed apparatus, three aluminum casting alloys and three constructional steels were tested for incendivity in frictional impact against rusted steel in flammable methane-air mixtures. Although varying in degree, all aluminum alloys investigated exhibited a high ignition probability under the test conditions; none of the steel specimens tested caused any ignitions under the same conditions.

Jan 1, 1973

By C. Manea

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra). Ecological remediation aims, among others, at decontamination of soils by preserving important properties as soil fertility.

Jan 1, 2008

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By Thomas E. McNider

On July 20, 1990, a Spontaneous Combustion Control Plan was approved by MSHA for Jim Walter Resources, Inc. No. 5 Mine. The mine operated under the plan for twenty-nine shifts before MSHA revoked the plan. A total of fifty-five seals were constructed during the process of implementing the plan. The major difficulty in applying the control concept resulted from problems controlling leakage at the numerous seals. The number of seals was a direct consequence of attempting to merge the traditional bleeder system, used in all the Blue Creek Mines, with the bleederless system Jim Walter Resources proposed as a means of controlling the spontaneous combustion hazard. This paper discusses Jim Walter Resources experience with spontaneous combustion control and the new safety standard which applies to underground coal mines that demonstrate a history of spontaneous combustion and how this standard would apply to our No. 5 Mine. The new Ventilation Standards were published in the Federal Register on May 15, 1992, and scheduled to go into effect August 16, 1992.

Jan 1, 1993

By Karen Bolm, Floyd Gray, Ailiang Gu, Kerry Caruthers, Carlos Velez, Laurie Wirt, Douglas M. Hirschberg

Understanding sources of dissolved metals and transport characteristics of acid drainage is needed to assist land-use strategies in mineralized regions, particularly in the semi-arid southwestern United States. Water- quality samples were collected from mined and un-mined parts of the Patagonia and southern Santa Rita Mountains of southern Arizona from streams, springs, seeps, adits, alluvial wells, and bedrock wells. Water quality during base-flow conditions was compared with that *of runoff samples from infrequent winter and summer storms. The largest fraction of annual discharge in these ephemeral streams consists of storm runoff, although springs provide a steady source of low discharge base flow to numerous intermittent perennial reaches. Several abandoned mines in the northern Patagonia Mountains contribute acid and heavy metals to streams. During base-flow conditions in mineralized areas, natural springs and intermittent stream reaches produce acidity but the volume is typically low and acidity is often diluted or neutralized down gradient. Overland runoff contains low concentrations of dissolved metals and moderate acidity, however, stream waters were strongly acidified and metal-laden from contact with abundant pyrite-bearing stream sediments derived from erosion of waste-rock material in and along the sides of the stream channel.

Jan 1, 2000

By C. W. Lockhart

Strength evaluation programs, based on sub- jecting a number of 5-718 inch (0.15 m) diameter core samples from highly fractured or poorly consolidated rock, to triaxial compression tests, have been successfully completed. An innovative approach was required since con- ventional methods with similar materials had not produced reliable results. Drilling methods were modified, and specially designed transparent core barrels were used. Sample preparation was successfully accomplished by using speciallydesignedtools and unorthodox hand- ling methods. Initial tests were carried out on weathered oxides from an open pit copper mine. The technique was later used successfully where the test material was weak, friable coal. The procedures used offer a practical method of testing weak materials where conventional methods would not be successful.

Jan 1, 1980