Search Documents

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By Danqing Gao, Brijes Mishra

Heterogeneity in rock formation affects both rock behavior and strength. Spatial variance of rock properties is an important characteristic of rock that addresses the heterogeneity of mechanical and physical properties and their effects on underground mining. Assessing spatial variance can be useful for locating potential difficult grounds and for performing reliability analysis in the mining support system. This study presents a spatially correlated, random model to investigate the influence of rock heterogeneity on rock strength and failure propagation. A random field database with specific spatial correlation was created for each physical-mechanical property using laboratory data and the extreme value stochastic model in MATLAB. Based on the improved microscale random model, we considered one three-dimensional numerical model to study a mine operating in the Pittsburgh seam. The influence of random field data on entry roof was investigated. The realistic random field database added two scale-measured parameters from horizontal and vertical directions to control the spatial correlation length. A number of cutting sequences were also considered in order to identify the effect of spatial variance on roof behavior. The results show that spatial variance provides an accurate prediction of erratic roof falls in coal mines.

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By E. Craig Simmons

Uranium is an element incompatible with respect to the major rock-forming minerals crystallizing from granitic magma, entering in- stead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late- stage fluids which can form ore deposits directly, or labile U which can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U- enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks which are most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite Mine area, Washington, have geochemical characteristics which fit very well the model presented here. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1981

By Yoginder P. Chugh

About 65% of the U.S. coal production (835 n tons was surface mined. A similar proportion of the Illinois basin's production (112 m tons) is also surface mined. The state of Illinois is the third largest producer of surface mined coal in the United States, after Wyoming and Kentucky. The Illinois coal basin encompasses Illinois, southwestern Indiana, and western Kentucky, as shown in Figure 1 (dotted lines). The estimated surface mineable coal resources in the basin amount to about 27 billion tons, and about 69 m. tons of coal is surface mined annually (Tab1e I).

Jan 1, 1981

By Hugh Boyd

Jet pulverization is a relatively new tool for fine grinding. It is not yet in general use in the mining and ore dressing fields, since most of the requirements in these areas have been for relatively coarse particle sizes. As the need for finer grinding increases - because of different ores, new products, and new values being sought - jet pulverization will, increasingly, be properly used.

Jan 1, 1969

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By T. H. Koenning

Spontaneous combustion in western U.S. coal mines has been recognized as a serious problem which requires unique solutions. Methods have been developed for longwall mining which rely on the existence of an oxygen-deficient atmosphere in the gob for control of the spontaneous combustion hazard rather than the use of bleeder systems. Monitoring of the gob atmosphere is required to protect against the possibility of an explosion and to detect spontaneous heatings. Data from an example mine employing such a system is included to illustrate normal gob gas trends and is compared to abnormal trends which resulted from and were indicative of a fire. Under normal circumstances the oxygen (O2) and carbon monoxide (CO) concentrations decline rapidly as the longwall face retreats. Samples taken from a leaking seal in the example mine prior to a spontaneous heating showed virtually no oxygen depletion, contained erratic CO concentrations, and indicated the existence of hydrogen, a fire indicator. The appearance of an abnormal trend in the gob atmosphere can be used as an early warning of spontaneous heatings.

Jan 1, 1992

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

Introduction One hundred years ago, a recent college graduate created the US aluminum industry. He found an economic way to crack the primeval bond that makes the metal so special. Aluminum doesn't "rust" - oxidize progressively. Rather, when exposed to air, it instantly forms a gem-hard but microscopic oxide coating. This seals off oxygen from the metal underneath. Scratch it and the seal reforms instantly. That tight chemical bond is the reason the metal is not found in nature; it exists only as a compound. The bond had to be broken to free the shiny metal. But once it is free, that self-sealing protection, alongside a remarkable strength-to-weight ratio, offers a marvelous material. Until 100 years ago, finding a way to do that economically was a challenge that defied science. Then it was solved, in a remarkable coincidence, on both sides of the Atlantic. And the way was paved for a material that would become the second most widely used metal in the world. Until that time, aluminum was a rare and precious metal. But then two young scientists independently invented the process that took aluminum outside the laboratory and into applications ranging from pots and pans to spacecraft. Discovery of aluminum Other major metals - copper, iron, lead, gold, and silver - had been used for thousands of years. But aluminum was entirely unknown until 1782, when French chemist Antoine Lavoisier suspected its presence. It was not actually discovered until Sir Humphry Davy, in England, detected it in clay in 1807. It was first isolated as a free metal only in 1825, by Denmark's Hans Christian Oersted. For years, laboratory methods yielded aluminum only in tiny amounts costing about $1200/kg ($545 per lb) - $13,333/kg ($6000 per lb) in today's dollars. Methods developed by French scientist Henri Sainte-Claire Deville in 1854 cut the cost to about $200/kg ($90 per lb). King Frederick VII of Denmark had a helmet of aluminum and gold. And Emperor Napoleon III of France reportedly served his most exalted guests at a state dinner with aluminum plates. He left the lower ranks to dine from pure gold. Deville and others continued to reduce production costs. But the price of aluminum still rivaled silver - $31/kg ($14 per lb) versus about $35/kg ($16 per lb) for silver. Then in 1884, a 2.8-kg (6.25-1b), 230-mm-tall (9-in.-tall) aluminum pyramid was cast as the tip of the Washington Monument. It was probably the first architectural use of aluminum. And it is still there after more than a century. The attractive properties of aluminum were obvious: it is lightweight but strong, conducts heat and electricity, reflects light and other electromagnetic radiation, and resists corrosion. But its commercial promise was blocked by its cost. In 1885, the price of aluminum was $17.70/kg ($8 per lb). It stayed there for the next couple of years until the Hall-Heroult process brought it down sharply. Hall-Heroult process lowers aluminum costs The characteristic that kept aluminum hidden so long continued to thwart chemists. Aluminum clings to oxygen so tightly that it is never found as a free metal in nature, and it is hard to break that bond chemically. The best chemical methods of the 1880s required sodium, and sodium itself was expensive. At Oberlin College in Ohio, chemistry professor Frank Fanning Jewett advised his students that anyone who could make aluminum inexpensive would do humanity a favor and get rich as well.

Jan 3, 1987

By J. M. Link

A technique is presented for the economic selection of a slurry pipeline with the aid of a computer. Mathematical models for the flows of homogeneous slurries are utilized. Only the pipeline and its prime movers are considered. Slurry flow properties are first obtained from rheology and/or pipeline data measurements. A rheological model is then selected for the slurry. It must be emphasized that the accuracy of the method is greatly affected by the accuracy of the slurry flow-property data. Approximate cost parameters may be selected from data for plain and lined pipes, centrifugal and positive displacement pumps, motors and engines. Cost data for the purchase, operation and maintenance of slurry pipelines are also described. A total cost equation for the ownership and operation of a slurry pipeline system is then established. The complexity of the equation is a function of the rheological model selected to describe the slurry. The equation is solved with the aid of a computer for several combinations of pipeline diameters and throughputs to yield minimum total annual cost for the system. A mean velocity is then computed to give the required throughput. The velocity is constrained by an upper and lower bound. A high velocity is undesirable from an energy consumption viewpoint and if pipeline wear is possible. On the other hand, the velocity must exceed the deposition velocity for a heterogeneous suspension or the critical velocity for a homogeneous suspension. There is no guarantee that the velocity developed by this method will lie within the constraints applied, nor that the constraints are even known. This is particularly true for heterogeneous slurries. An important feature of the method is the ease with which the variables can be adjusted to measure the sensitivity of the total cost to the variables. The purpose of the sensitivity analysis is to identify those critical variables that. if changed, can considerably affect the total cost. Mathematically, individual variables are changed and the effect of such a change on the annual total cost is computed. But from a designer's point of view, individual components in the system are changed to study their effect on the annual total cost. A change in one component of the system may involve a change in one or more variables. For example, the replacement of a steel pipe by a smooth-lined pipe will change the pipewall roughness and wall thickness as well as purchase, operating, and maintenance costs.

Jan 1, 1974

By Greg Beckstrom

Minnesota is a major mining state. This statement is not a dream or stretch goal but is a fact. As reported in a recent edition of Mining Engineering magazine, Minnesota ranks as the third largest state in terms revenues generated from nonfuels mineral production. The vibrancy of the mining sector in Minnesota can be attributed to several factors. The northeastern corner of the state is home to Minnesota?s iron range, one of North America?s largest deposits of iron ore. Iron ore from Minnesota is a strategic resource that has been [ ] instrumental to the nation?s development ? 90 percent of the iron used to build ships and planes during World War II came from Minnesota. Taconite pellets now produced from openpit mines on the iron range are shipped to steel mills worldwide. The growing appetite for steel in China and India has reignited once moribund mining operations throughout the iron range.

Jan 1, 2012

By Deepak Malhotra

Western technology is considered a panacea for all ills in developing countries. Is that really the case? Are inventors of new technology overselling? What are the expectations of the receiving party? The author offers his views on these questions and proposes a process for systematic transfer of technology while minimizing surprises on the part of the seller and the receiver.

Jan 1, 2001

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By S. Miller, A. Krasner, M. Sizintsev, S. Schafrik, H. -P. Chiu, J. Sottile, A. Rajvanshi, Z. Agioutantis

In recent years, a great deal of effort has been put into automating mining equipment with the goal of improving worker health and safety and increasing mine productivity. Significant progress has been made in automating mining equipment such as load-haul-dumps and drills in underground environments where global positioning systems are unavailable. This paper addresses automating the task of positioning the shuttle-car (SC) under the continuous-miner (CM) coaldischarge conveyor during cutting and loading operations. A stereo depth camera is mounted on the SC. Machine learning based algorithms are applied on the camera’s output to identify the CM discharge conveyor and segment the scene into various regions such as roof, ribs, and personnel. This information is used to plan the shuttle car path to the CM discharge conveyor. The approach currently uses a 1/6th scale continuous miner and shuttle car in an appropriately scaled mock mine

Mar 2, 2022

By M. H. Col

Within the last few years, there have been numerous techno-logical advancements within material handling due, in part, to the introduction of conveying systems and mobile material handling systems to the industry. Although the traditional material handling methods are still commonly used, the introduction of conveyors to the industry has provided companies with some very efficient and economical options. These "new" systems change with the industry to accommodate rigorous demands, ease of operation, and low operating cost requirements. The number of mobile material handling systems utilized in mining operations is increasing, especially in heap leaching applications. Ten years ago, mobile material handling systems like Mobile Stacking Conveyors (MSC) were considered a novelty. There were two (2) MSC's in actual operation and only one of those in a heap leaching application. Today there are numerous proven systems operating at mine sites around the world-La Coipa, Zaldivar, Florida Canyon, Cananea, El Abra, Chuquicamata, and Radomiro Tomic. The popularity of mobile systems is due to the benefits realized by individual projects. As technology advances, so do the concepts behind mobile material handling systems. Implementing self leveling mechanisms, Programmable Logic Controllers, and Global Positioning Systems to control the equipment are just a few of the recent advances that will be discussed in this paper. We will also discuss current proven systems, and touch on what we see as some of the future advances.

Jan 1, 1998

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee's Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today's competitive markets.

Jan 1, 1984