Search Documents

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By Peter C. Lighthal, Harvey N. McLeod, Iain G. Bruce

This paper describes the practical aspects of handling cyanide leach tailings. Alternative systems for cyanide destruction are briefly discussed. The provision of adequate retention time to allow natural degradation of cyanide during summer months is the most economical method of cyanide destruction. Cyanide in ground- water can frequently be both persistent and mobile, so that tailings basins should be designed to limit seepage. Common methods for limiting seepage are presented. Other aspects addressed are water balance, winter operation and abandonment of cyanide tailings systems. A case example of the Cheni Gold Mines Lawyers Creek Project tailings handling system is presented.

Jan 1, 1987

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By Claude Hébert

The Grenville structural province, a 400 km-wide belt of Precambrian metamorphic rocks which crosses the province of Québec in a northeasterly direction, is the host of several wollastonite occurrences. Most of these are found in marble and calc-silicate rocks enclosed within or located near intrusive bodies. Reconnaissance and detailed mapping of such zones have helped to identify areas of interest for wollastonite exploration. The most important zone is located in the huge Lake Saint-Jean anorthosite massif in the central part of the Grenville. A recent geological mapping project has revealed the presence of wollastonite in metasedimentary faulted remnant of the roof. The main occurrence consists of diopside and wollastonite in a zone at least 3 km long and 150 m wide. Preliminary sampling suggests and average grade of 50 percent wollastonite with an aspect ratio of 151. Other wollastonite deposits occur in the western part of the Grenville, mainly north and west of Montreal, where the Morin anorthositic complex and a large syenite mass intrude the metasedimentary rocks of the Grenville Supergroup. Marble bands with up to 70 percent wollastonite occur locally at the southern margin of the complex or as an inclusion in the syenite. Significant wollastonite occurrences have recently been found in the eastern part of the Grenville. One of them is located in metamorphosed calcareous rocks which are part of the granulite facies Manicouagan metamorphic complex. A representative sample analyzed 54 percent wollastonite. Farther south, an inclusion diopside-wollastonite gneiss containing an estimated 40 percent wollastonite occurs at the margin of the Pentecôte River anorthositic complex.

Jan 1, 1995

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By Max John

INTRODUCTION One of the main advantages of the New Austrian Tunneling Method (NATM) is its adaptability to varying rock conditions. This method is therefore successfully applied when complex geologic features are expected which cause uncertainties in the prognosis of the rock mass behaviour, as was the care at the Arlberg Expressway Tunnel. Furthermore, by employing the NATM problems are avoided when encountering varying geologic conditions or even extension fault zones along the tunnel, as was the case at the Dalaaser Tunnel and Perjen Tunnel. The NATM can also be used for rock and soil. The following examples will show how various rock conditions can be mastered. In accordance with the NATM all tunnels which will be discussed are road tunnels having a cross section area between 70 and 100 m2. The construction consists of a primary support, which ensures stress redistribution during excavation (Figure 1). The primary support is reinforced shotcrete strengthened by steel arches, when necessary, and rock bolts. When encountering rock pressure, swelling rock or soil, the primary support is suplemented by an invert arch. The purpose of the secondary lining is to increase the safety of the tunnel with regard to long-term stress redistribution processes or changes in rock mass properties as well as to protect the insulation. The secondary lining consists of cast concrete without reinforcement and is generally 0.25 or 0.30 m thick.

Jan 1, 1981

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By R. W. Barbaro, R. V. Ramani, K. V. K. Prasad, P. T. Luckie

The limitation of sulfur dioxide in power plant In this study, the following quality parameters of the coal emissions dictates that sulfur in coal be reduced to the lowest possible level before combustion to not aggravate the emission control problem at the stack. For coal-fired power plants, the methods in practice to achieve low-sulfur coal include mining areas with relatively low sulfur, reducing sulfur in the mined coal through preparation techniques and blending high- and low-sulfur coals. A prerequisite to the successful implementation of any of these practices is the knowledge of the spatial distribution of sulfur and the capability to predict its value in mining blocks. In this paper, the results of a study conducted to evaluate the applicability of geostatistics for describing the short scale variability of sulfur in a coal seam are presented. Four sides of a block of coal to be mined by the longwall method were extensively sampled at closely spaced intervals. The details of the longwall sampling plan and analysis procedures are discussed. The results of the statistical and geostatistical analysis are presented. The implications of these for prediction of sulfur for control purposes are examined.

Jan 1, 1991

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

Sweden is beginning to reap the rewards of a process that has transformed a country with a history of metal mining into one of Europe's most vibrant exploration regions. Exploration and mining companies from North America, Europe and Australia have joined local firms in the search of gold, base metals and diamonds. This has been due to changes in Sweden's mining laws in the early 1990s. These changes opened the way for unhindered private sector investment in the country's mineral industry. More than 20,000 km2 (4.9 million acres), mainly in northern Sweden, is now held under granted or applied exploration claims. Exploration permits diamonds, applied or granted covers more than half of Sweden's surface. This is a greater proportion of the country than ever before. Major mining companies and junior explorationists are evaluating a geological potential that bears favorable comparison to other major mining centers. Historically, Sweden's gold re- sources occur in greenstone belts in northernmost Sweden and in association with massive sulfide deposits in the Skellefte district. These are receiving particular attention by exploration companies. In addition, new areas in Sweden are also being explored for gold. This increases the probability that Swedish gold production - already the highest in Europe - will increase in the future (Table 1). Sweden's recorded mining history goes back for much of the last large pool of expertise in exploration, mining, equipment manufacturing and minerals industry research. In addition, the Geological Survey of Sweden provides sup- port for exploration in terms of data archives, processing and publications. Other benefits for exploration companies are Sweden's communications infrastructure, its member- ship in the European Union, bringing access to one of the world's major markets and the high level of educational, technical and language skills held by the country's work- force. And deregulation of the economy and the introduction of competitive corporate tax rates have made Sweden a favorable destination for investment in Europe.

Jan 1, 1997

By Elisa Comis, David Chastka, Miriam Piemontese, Maria Chastka

The Lower Olentangy Tunnel (LOT) Project involves the construction of a 17,000 ft (5,200 m) long, 12 ft (3.65 m) internal diameter Combined Sewer Overflow (CSO) tunnel. The tunnel is excavated by using an Earth Pressure Balance (EPB) machine designed to cope with soft ground, weak rocks and water pressure. The project is located in the city of Columbus, Ohio and the main geotechnical hazards are related to the heterogenous soils and the low overburden in an urban environment. This paper focuses on the performance of the EPB first drive and the comparison between the design assumptions and the actual TBM performance during construction.

Jun 23, 2024

By T. R. Ellis

"Editor’s Note: This is an expanded abstract. The full report is available on SME’s website at http://www.smenet.org/publications-resources/ resources/sme-valuation-standards-tutorials.The author has three goals for this review of mineral valuation standards internationally.1. To place the SME Standards and Guidelines for Valuation of Mineral Properties (SME Valuation Standards) and International Mineral Property Valuation Standards template (IMVAL Template) within the global context of existing mineral valuation standards.2. To review the current status of harmonization of each International Mineral Valuation Committee (IMVAL) member’s mineral valuation standards (or code) with the IMVAL template and suggest remedies for issues found.3. To suggest future enhancements for the IMVAL Template and SME Valuation Standards, and to suggest future roles for the IMVAL and SME committees. From the author’s review, Ellis draws the following conclusions.The SME Valuation Standards comprise a minimum set of principles-based standards and guidelines for developing and reporting valuations of mineral properties (including petroleum properties) for public and private use, subject to jurisdictional requirements. The standards are also designed to provide mineral valuation guidance that supplements application of the International Valuation Standards Council’s International Valuation Standards (IVS) and the U.S. government endorsed Uniform Standards of Professional Appraisal Practice (USPAP), published by the Appraisal Foundation.The SME Valuation Standards is the first set of valuation standards developed by a minerals institute adopting and modifying the IMVAL template. As a result, the SME standards are essentially totally harmonized and otherwise aligned with the IMVAL template. IMVAL was initially conceived in 2012 as a discussion body to aid harmonization of each member’s valuation standards, by modifying to function the same. IMVAL primarily developed the IMVAL template, published in July 2016, to produce an agreed reference framework of essential mineral valuation guidance content as the goal for harmonization of the Australasian Code for Public Reporting of Technical Assessments and Valuations of Mineral Assets (VALMIN Code), The South African Code for the Reporting of Mineral Asset Valuation (SAMVAL) and the Canadian Standards and Guidelines for Valuation of Mineral Properties (CIMVal standards and guidelines). The harmonization would result from each mineral valuation standards committee modifying its standards to operate similarly to the IMVAL template, producing valuation reports with similar content and value for the same mineral property. The template is also available for other bodies to adopt and modify for their regional setting’s needs, as SME did, or use as a convergence goal when updating an existing standard."

Jan 2, 2018

By Robert C. Schenk

The rapidly expanding, globally based mining industry provides many opportunities and challenges for the engineering construction business. This paper reviews some of the innovations that the industry is implementing to provide increased value in the design, construction, and successful start-up of new mine plant facilities. Approaches being taken to reduce installed-plant costs as well as related value-enhancement opportunities are discussed. Included are comments on new technology developments, use of automation and global communications networks, application of economic models as a project design tool, and management approaches being adopted to make the engineering construction process significantly more effective.

Jan 1, 1998

By H. Janas

In a gas/coal outburst the gas plays an active, driving part. The proneness of coal to outbursts can be determined by means of its gas emission properties, since coal that is liable to outbursts differs from coal with normal gas emission properties in that it liberates its gas from the sorptive bond more quickly. There is a risk of outburst when the flow of metha¬ne originally desorbed by the coal is sufficient to move the loosened coal which has been broken suddenly. The violence of a gas/coal outburst can be evaluated from the distance of projection of the mass of coal. It depends on the gas pressure and on the liability to outburst of the coal at the original centre of the outburst. Both factors are complementary in their effects so that the same work is done in a gas/coal outburst when there is a high gas pressure and low proneness to outburst as when there is a low gas pressure and a higher proneness to outburst. The gas pressure in the coal increases with its gas content. Consequently it is possible to deduce the gas pressure of a coal seam from its gas content. In the Federal Republic of Germany the risk of a gas/coal outburst is thought to exist when the desorbable gas content of the coal reaches or exceeds the value of 9 m3/ton and if the specific limit value of the proneness to outburst is exeeded. The Mine Ventilation Testing Station of the Westfalische Berggewerkschaftskasse has developed a new method for determining the risk of gas outbursts immediately after taking the samples at the coal face (1), (2).

Jan 1, 1980

By G. D. Trump, F. L. Stanley

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce the cut point and improve separation efficiency. Preliminary economic analysis show that the new circuit provides an attractive payback on capital investment.

Jan 1, 1999

By T. J. Cox

The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. An approximate 12-mile segment of the river from the town of Red River to the village of Questa (Questa) includes several hydrothermal alteration zones. Alteration ?scars? formed as a result of rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks. Storm water runoff from the scar drainages contributes metal-laden, acidic water to the river and creates a visible plume of discolored water in the river. Acidic runoff reduces the river pH from 7 to the mid 3s for at least 2 hours during large storms and the low pH water continues downstream. Runoff from scar drainages increases some metal concentrations in the river from below chronic ecological criteria to as much as two orders of magnitude greater than acute ecological criteria, and results in acutely toxic conditions for macro-invertebrates. A general improvement in the river?s water quality occurs downstream due to dilution from tributary inflow from non-mineralized watersheds, the natural buffering capacity of the river, and storm water controls at the Chevron Mining Inc. Questa mine.

Jan 1, 2011

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970