Search Documents

By James T. Furey, Laurence D. Hartzog, Graham A. Karklin

A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from the gold/tellurides bearing sulphide ore of the Kensington deposit (Echo Bay Mines and Coeur d'Alene Mines), and to compare the performance of column flotation to conventional "mechanically agitated" flotation, Tests were conducted in a 150 mm diameter, 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail. The bulk metallurgical ore sample had an average "as tested" feed grade of about 5 git gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbrayite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of97%, but produced grades of +150 git Au.

Jan 1, 1992

By Nicholas Tabor, Norbert Fuegenschuh, Richard Taylor, Jean-Marc Wehrli

The Plymouth Tunnel forms part of the 16-mile long route of the Purple Line Light Rail Project promoted by the Maryland Transit Administration. The tunnel is approximately 1,220 feet in length with a shallow vertical alignment located beneath a residential area. Challenging mixed ground conditions included surficial soils, decomposed Saprolite, and highly weathered to fresh rock requiring the use of the Sequential Excavation Method (SEM) for construction. This paper discusses innovative approaches implemented during construction as well as challenges faced during planning and installation of a spray-applied permanent concrete liner.

Jun 13, 2021

By B. Salopek

The greatest part of crushed stone, gravel and sand production is extracted through open pit operations, whereas gravel and sand are also partially extracted from riverbeds. Its obvious that such a mining activity provokes some changes in the configuration and environmental characteristics of the region, in the temporary or permament disapperance of vegetable or animal species and in the creation of noise, dust and waste water. However, the above-mentioned mining operations shouldn not have only negative effects on the landscape and land potential, but they can discover and predetermine the potential of the exploited areas for various communal purposes after exploitation (eg. sports and recreation centers, campsites, resorts, fish-farms, etc.). In this paper, the production of construction aggregates in plants located in the vicinity of Zagreb, the capital of Croatia is presented. The advantages and disadvantages of aggregates? production in urban areas in the spirit of sustainable development are discussed.

Jan 1, 2003

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By John MacDonald

An unstable economy has shown businesses what the mining industry has known for decades ? a successful business location today may not succeed in the future. Unexpected expenses, natural events and workforce changes have a big impact on the costs of production. To help focus production and maintenance budgets, mining executives are increasingly turning to production metrics to make key decisions. Role of mine and mill data Companies employ a variety of information systems to allow employees to accomplish their operational tasks, and each worker is focused on the metrics, or key performance indicators (KPI), for his or her individual function. For example, machine operators monitor throughput and cycle time to keep the machines running continuously and to meet daily production quotas. Meanwhile, the maintenance teams monitor machine performance, overall equipment effectiveness (OEE) and meantime between failure to predict and help prevent downtime.

Jan 1, 2013

By G. K. Derby

Paper presents project results investigating current techniques for dragline wire rope removal and the development of less hazardous means of performing the task. The cannon is the most prevalent method used in American surface mines. A cannon test program was conducted that used 40-and 50-grain primer cord to establish force produced using a 56-pound projectile. Socketlwedges were separated to establish separation force data. Two alternative removal methods, pendulum ram and portable hydraulic pusher, were developed and tested. Both provide sufficient force to effect separations under normal conditions on draglines with up to 78- cubic yard buckets.

Jan 1, 1984

By Gy. Deák

The Romanian mining and especially the salt mining industry is going through a restructuring phase; among others it has to respect the European Environment Act. One of the most important deficits of the salt mining industry is the implementation of monitoring systems for geomechanics phenomena, in order to develop an important information database and form a real base for salt mines stability, prediction and prevention measures. Monitoring system solutions, involving discontinuous and continuous measurements of displacement / deformation fields, around underground excavations, are presented and discussed. In addition, a case study for the stability prediction of an experimental salt off-set, located in the Praid salt mine, using DKRControl method, is presented. The two monitoring systems use different tools, namely measuring tapes (to determine distance between markers in T-D station) and ultrasonic transducers (SM-TDA equipment).

Jan 1, 2006

By Z. T. Bieniawski

Engineering rock mass classifications have received prominent attention as design aids in rock tunneling. Support selection in civil engineering tunnels and chambers is often based on such classifications. In the field of mining, rock mass classifications have not been utilized to the same extent but some applications have been made. This paper considers the current rock mass classification schemes from the point of view of their potential in mining. Case histories are described featuring their use in assessing the cavability of ore as well as entry stability and support. Current possibilities for rock mass classifications as design aids in mining are outlined.

Jan 1, 1980

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By S. Bhamidipati

Abstract. Controlled flow is an aspect often desired in mine ventilation. This is normally obtained by using fans and regulators to achieve the required pressure balance in the system. Preference for a certain network layout of these control devices is influenced by technical as well as legal and economic factors. In this study, a model is developed based on an economic criterion by which an optimum layout of fans and regulators for a controlled flow system can be determined. The concept is analo¬gous to the critical path crashing. However, a linear programming package is used to demonstrate the solution procedure for a hypothetical venti¬lation network.

Jan 1, 1983

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

The mining and minerals extraction industries have often been demonized by the public as industries that put profits and production before people. It is true that the inherent danger of the work has led to more fatal accidents than anyone associated with the industry would care to remember. But, in stark contrast to what has often been said, the truth of the matter is safety is now the top priority of every miner, from the face of the longwall to the executive boardroom. Without safety, nothing else matters. This message was told and retold by representatives from some of the world?s top mining and petroleum companies from Oct. 11-13 during the inaugural Safety and Reliability in the Mining and Resources Industries Conference in Calgary, Canada. The meeting was hosted jointly by the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) and the Society for Mining, Metallurgy, and Exploration (SME). It was the first of a series of conferences to focus on these important topics. Next year, the conference will be held in Minneapolis, MN from Nov. 13-15.

Jan 1, 2011