Search Documents

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019

By Jerry Solomon

The subjects to be examined in my portion of the session entitled "Technology of Aluminum.. Recovery" will be twofold. 1. Economics of the basic aluminum economy--supply-demand-price. 2. Specifications of aluminum products produced from municipal waste--from the secondary aluminum standpoint. It is the object of this speech to first impress everyone with the excellent long-run markets for the aluminum products from municipal waste and then to acquaint everyone with the rather liberal scrap specifications that the recycling industry can tolerate. The most important statement that can be made about the recycling of aluminum is that it is now and will be an economic necessity. This is true far many reasons; one which hit the headlines recently was Interior Secretary Rogers Morton's statement "Third-world nations could use mineral wealth not to achieve political ends but to jack up economic positions. The result could be sky-rocketing prices and dwindling supplies on world markets." There is no reason why the group of countries that supplies most of our bauxite can't get together the way oil-producing countries got together on the price of oil. (Jamaica and Surinam, are original sources of two-thirds of the aluminum used in the United States.) The worry is not so much that we will end up without the basic raw material but rather that the price might be so high that we could not afford it. So much for the blackmail reason for recycling aluminum; the supply and demand picture in both the primary and recycling sectors of the aluminum economy is far more meaningful.

Jan 1, 1974

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By K. J. Ashley

Over the last six years I have been involved with the calculation of ore reserves and mine planning using various computer systems and soft- ware packages. This experience has given me a unique perspective from which to view the needs of the engineers and geologists whose job it is to produce geologic and mineable ore reserves. The purpose of this paper is to share that perspective with those who are in this field or are thinking of purchasing computer software to aid in these calculations. My first experience with computers in mining was the creation of a mini-computer based coal reserve and mine planning package written as part of my Easter's thesis. This package took about ten weeks to write, four weeks to document, and two weeks to install at the mine for which it was written. It did what it was designed to do, which was to emulate the hand procedure which had been used prior to its installation. The package was specific to its application which involved several small seams of coal being mined simultaneously and would have required major modification for it to be applied to a mine where, say, one thick seam was mined in two benches.

Jan 1, 1985

By H. Evans

It is well known that iron-ore pellets are considered one of the best blast-furnace burden materials used today. The demand for pellets is demonstrated by the increase in pellet output from one million tons in 1955 to approximately 37 million tons in 1964. This growth continues as new plants are placed on-stream each year. The consumer generally specified (1) the acceptable content and range of chemical constituents, (2) a minimum strength determined by some standard testing procedure, (3) the size range of pellets, and (4) perhaps a measure of reducibility.

Jan 1, 1966

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By D. A. Baker, E. A. Gyawu, K. Awuah-Offei

Several underground coal mining disasters, such as Upper Big Branch in 2010, have revealed technological and organizational shortcomings related to self-escape. Efforts to address these gaps have primarily been top-down, that is, identified and implemented by upper management or external governing bodies. In contrast, this study employs a novel miner-centered approach to identify perceived technological boundaries to self-escape. Using a semi-structured, scenario-based survey, we elicit direct feedback from miners about current, emerging, and hypothetical technologies aimed at improving self-escape during mine emergencies. The results show a general high usefulness rating across all 21 technologies in the survey. Miners who work underground (both outby and working face miners) appear to give higher usefulness ratings overall than miners on the surface and other locations. This work will be directly applied to a series of proof of concept and prototype studies on self-contained self-rescuers (SCSRs), refuge alternatives (RA), and communication devises aimed at improving self-escape technologies through miner-centered research and design.

Mar 2, 2022

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By David D. Lambert

REE analyses of cumulate plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma can- not be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data is more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE bearing sulfides of the J-M Reef are associated with such a re- appearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultramafic zone of the complex.

Jan 1, 1981

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

By John Turner, John A. Gibson, David Cass

Contents A. Introduction B. Description of Robbins Company involvement in several of the English Channel Tunnel projects C. Identification of project requirements and comparison of TBM features D. Description of the manufacturers separate roles in the -235 (T-1) TBM E. T-1 performance to January 15, 1989 F. Summary

Jan 1, 1989

By T. R. Ellis

"In August 2013, the Appraisal Practices Board of the U.S. Appraisal Foundation issued its “APB Valuation Advisory #4 - Identifying Comparable Properties,” which contains analysis and examples that may suggest a broader meaning of the term “comparable properties” than is current convention in real property value appraisal in the United States and internationally. The advisory is directed at the appraisal of real property of all kinds, including interests in mineral properties, as indicated by the inclusion of two mineral property appraisal papers in the appendix that lists suggestions for further reading.This paper firstly reviews as background the historical meaning of a comparable property, with its perceived constraints, against real-world examples of transacted mineral properties that are adjusted to subject properties to provide market value indications. The advisory’s findings are then examined and evaluated as to whether they may influence and benefit the work of mineral property appraisers, particularly in situations where their sales comparison analyses may be challenged. The conclusion is that the combination of constraints that the advisory’s findings specify for use of the term “comparable” will for mineral properties be met infrequently or rarely. As a result, mineral property appraisers are advised to avoid using the terms comparable or “comp” when referring to transactions of mineral properties that they analyze to derive data for appraising the value of their subject mineral properties. IntroductionA mineral property appraiser rarely finds a sale of a mineral property that meets the literal meaning of the term “comparable sale,” by being directly comparable to the subject property of the appraisal in all factors of significance in the determination of the value of the property interest being appraised. Real estate appraisers have long used a more liberal interpretation of the meaning of comparable sale and its commonly used abbreviation, “comp.” Real estate appraisers compare sales to their subject property on the basis of price per hectare or acre of land and price per square meter or square foot of building floor area. Adjustments totaling to within the range of +30 to -30 percent from the sale property to the subject, before factoring in the property area, have generally been viewed as appropriate for the sale to be considered a comparable sale."

May 1, 2016

By Chen Bingchen, Ma Shaojian

A new magnetic liner, with unique magnetic circuit and novel structure designs, was developed. It was characterized by light weight, low noise, as well as corrosive and abrasive resistance. The wear rate of the magnetic liner was one twentieth and one ninth those of the manganese-alloy steel and rubber ones respectively. The forming mechanism of the protective layer and that of influencing factors on magnetic liners were also investigated. The research results could not only instruct using magnetic liner, but also widen their application.

Jan 1, 1995

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By John H. Clark

This paper outlines new technological improvements in underground trackless equipment for the metal mining industry with emphasis on maintenance related developments for Load Haul Dump machines. Also new developments on other types of equipment are covered including drills, road headers and electric LHD's.

Jan 1, 1983

By Robert J. Auber, Thomas R. Scotese

The West Leg Interceptor is part of a new sanitary sewer system in the southwest suburbs of Cleveland. The first two construction contracts were excavated in glacial soils varying from hard tills to pressurized silts and flowing sands. These soil and groundwater conditions were locally problematic during shaft and tunnel excavations and final lining construction. A variety of solutions were developed primarily during construction. During the WLI-1R Contract, subgrade pressures, continued ground losses, and displacements necessitated extra eductor wells and modified inverts for stabilization of shafts. At the WLI-2Contract, one shaft excavation in similar ground required only one extra well. In the WLI-1R tunnel, localized inflows of groundwater, silt, and sand through the geotextile fabric were stopped by cement grouting. In one WLI-2 connector tunnel, damage to the TBM flood doors combined with wet, flowing silt and sand led to ground losses, surface settlements, plugging, patching, and chemical grouting. The concrete lining in the main WLI-2 tunnel required remedial work to improve watertightness at joints.

Jan 1, 1999

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992