Search Documents

By K. M. Belingheri, M. E. Smith

Pinson Mining Co. operates a conventional mill and two heap leach operations in north-central Nevada. The latest of these heap leach operations, the Preble project, is a low-grade, low-tonnage property made profitable through several innovative capital reduction techniques. Rapid return on investment was a prime factor in design. To facilitate this, fast-track design and construction techniques were employed. The project is a seasonal 1.5 kt/d (1 700 stpd) crush/agglomerate heap leach plant using both clay and plastic leach pads. Construction and startup were achieved through cooperative arrangements between local contractors and in-house construction personnel, with few items put out to bid. An interactive approach to design minimized lost time and construction costs.

Jan 1, 1987

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By V. Králová

The TESCAN Integrated Mineral Analyzer (TIMA), an automated mineralogy system, enables fast and quantitative mineral analyses of rocks, ores, concentrates, tailings, leach residues or smelter products. It combines BSE and EDX analysis for identification and measurement of mineral concentrations, particle size distribution, and liberation/locking parameters. In addition, it can provide bright particle searches for PGM, gold-silver ores, and/or REE. With the newly developed Automated Loading System (AutoLoader), the TIMA has become the world?s first automated mineral analyzer which permits robust, continuous and unattended sample loading. With the AutoLoader (robotics) system, the TIMA has emerged as a powerful plant support instrument. It increases the sample throughput, minimizes manual labor and enables 24/7 operations. As such, it can be used in daily, continuous mineralogy for mine geology/ore control, concentrators, leach operations, and smelter support. It will also increase the capabilities of technical service centers for mining companies, commercial laboratories, large drilling programs or pilot test campaigns. In combination with a highly automated sample preparation lab (sizing, potting and polishing), TIMA technology can establish high-throughput and fast-turnaround automated mineralogy lab modules for mine-site production support.

Feb 23, 2014

By M. J. Zdunczyk

The final 1995 figures on industrial sand and gravel have not yet been compiled by the US Geological Survey (USGS). There is usually about a nine-month lag time in receiving and compiling this information. However, USGS estimates that domestic production of industrial sand and gravel will increase about 4% to 28.2 Mt(31 million st). The average unit price is expected to increase as well. The top five producers during 1995 were Unimin, US Silica, Fairmount Minerals, Oglebay Norton and Morie Co. Glass manufacturing for containers, automobiles and buildings was mixed during 1995. Containers, the largest consumer of silica sand, remained steady, with regional increases. However, silica use in glass containers face increased competition from plastic and recycled glass (cullet). It was reported that the Pepsi Cola announced plans to replace glass containers with plastic during 1996.

Jan 1, 1996

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By Robert A. Pimentel

Dust is still a major problem in increasing production from longwall faces. Over the last decade, significant improvements have been made in the development of techniques for reducing dust exposure on conventional and continuous sections. But virtually no improvements have been made in dust control on longwall sections. It is true, that there are many more continuous mining sections than longwall sections in the United States and that the number of workers overexposed on continuous miner sections is much larger than the number on longwall sections. However, the problem on continuous miner sections appears much easier to solve and, in fact, we believe that the techniques are available to get virtually all continuous miner sections in compliance. The problems on longwall sections are much more elusive. Also, the number of longwall sections in the United States is expected to increase during the 1980's. Thus, dust control on longwall sections remains a formidable and important problem. Companies operating longwall sections with a dust problem are faced with the tasks of having to quantify the various dust sources, of selecting proper techniques to reduce the problem, of implementing the techniques and of evaluating their effectiveness.

Jan 1, 1983

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By Roderick K. Davey

Kennecott Copper Corp.'s Metal Mining Div. operates three major open-pit copper mines in the western United States. These operations include Utah Copper Div., Ray Mines Div. in Arizona, and Chino Mines Div. in New Mexico. At each of these operations, the material is loaded by large electric shovels and transported by both truck and rail haulage. In 1977, 197 350 774 t (217,542,000 st) of ore and waste were mined at these operations, and 302 040 t (332,942 st) of copper were produced. Also a significant amount of molybdenite was produced as a byproduct. In operations as complex and large as these, there is an inherent need for up-to-date reports concerning how much material was mined during the previous day, and year-to-date, what equipment is scheduled for maintenance, how equipment has been performing, etc.

Jan 1, 1979

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By E. D. Gardner, William O. Vandenburg

This chapter on the square-set system of mining em¬bodies the results of a special study of the subject made as a part of the US Bureau of Mines (USBM) general investigation of mining methods and costs. Data for the chapter were gathered by the authors during visits to mines using square-set mining, from information circu¬lars prepared by consulting engineers to the USBM on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. Al¬though some of the properties discussed are no longer in operation, the methods described are still valid. The square-set system of mining has been very widely applied and is one of the oldest methods in use in the US. It is mainly employed for extracting rela¬tively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and¬fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50% of the ore may be extracted by square setting at mines listed as using some other method of mining. A large tonnage has been mined yearly by square setting, prin¬cipally in the western states. Due to the high cost of timber and the relatively low average production per manshift, this system generally is not used when the ore can be mined by some other method; it usually is adopted as a last resort. Square setting, however, has a special field in that ore bodies not minable by other methods can be stoped by this system. As square-set mining was widely known, there was a tendency for years to use the method regardless of its suitability. With the increasing need for economy and the development of other methods, square setting has been superseded in many mines by cut-and-fill, top slic¬ing, or sublevel caving methods. The term square-set mining as used in this chapter includes all stoping methods in which the space made by the removal of the ore is timbered with framed sets. The sets usually are square in horizontal section. The stope may or may not be filled with waste rock as stoping progresses. HISTORY OF THE SQUARE-SET SYSTEM Prior to 1860, open-stope methods with stulls for casual support accounted for most of the mineral pro¬duction from underground mines. Attempts to mine large ore bodies that required artificial support resulted in disastrous cave-ins and loss of life. The art of mining received a tremendous impetus following the introduc¬tion of methods for mining the bonanza ore body which was discovered in 1860 in the Ophir mine on the Comstock lode, Virginia City, NV. This ore body was phe¬nomenally rich and eventually proved to be 122 m (400 ft) high, 27 m (90 ft) wide, and 98 m (320 ft) long. The mining of this large high-grade ore body taxed the best engineering talent of the time; the problem was finally solved by Philip Deidesheimer. According to Eliot Lord (1882): "At the 50-foot level the vein of black sulphurets was only 3 or 4 feet thick, and could be readily extracted through a drift along its line, propping up the walls and roof when necessary by simple uprights and cap-posts. As the ledge descended the sulphuret vein grew broader until, at the depth of 175 feet, it was 65 feet in width, and the miners were at a loss how to proceed, for the ore was so soft and crumbling that pillars could not be used to support the roof as in coal mines. They spliced timbers together to hold up the caving ground; but these jointed props were too weak and ill-supported to with¬stand the pressure upon them, and were constantly broken and thrown out of place. The dilemma was a curious one. Surrounded by riches, they were yet un¬able to carry them off and their mass of black sulphurets bade fair to become a white elephant on their hands. The Ophir Company began to wish themselves less for¬tunate, as their miners narrowly escaped burial day after day in their attempts to stope out the ore. "A young mining engineer, Philip Deidesheimer, was in charge of a quartz mine in Georgetown, El Dorado County, Calif., in the autumn of 1860, when this serious check to the development of the lode occurred. At the request of William F. Babcock, a trustee of the Ophir Company, Mr. Deidesheimer left his California mine and crossed the mountains with a letter from the direc¬tors of the Ophir Company, authorizing him to inspect the workings of their mines and make such changes in the method of timbering as should seem to him expe¬dient. After examining the vein he designed, in the course of a few weeks, a system of timbering which proved to be exactly adapted to the requirements of the work. Experiments which he had previously made in California gravel and quartz mines furnished the out¬line of his plan. This was to frame timbers together in rectangular sets, each set being composed of a square base, placed horizontally, formed of four timbers, sills, and crosspieces from 4 to 6 feet long, surmounted at the corners by four posts from 6 to 7 feet high, and capped by a framework similar to the base. The cap pieces forming the top of any set were at the same time the sills or base of the next set above. These sets could readily be extended to any required height and over any given area, forming a series of horizontal floors, built up from the bottom sets like the successive stories of a house. The spaces between the timbers were filled with waste rock or with wooden braces, forming a solid cube when¬ever the maximum degree of firmness was desired. By adjustments of these sets the ore bodies along the line of the lode were extracted with comparative ease and security." Most mining methods are evolved slowly and are the result of the combined efforts of a number of minds; Deidesheimer's feat was remarkable in that his system was immediately successful. He died in 1916 at the age

Jan 1, 1982

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By S. Dixon

The use of warm (40-50°C) solution for the selective elution (pre-strip) of copper cyanide from gold and silver cyanides adsorbed on activated carbon was found to elute +90% of the adsorbed copper compared to the use of ambient (20°C) solution eluting 50-70% of the adsorbed copper. The warm solution pre-strip elution did have higher co-elution of gold (1-4%) and silver (10-18%) with the copper. The use of ambient solution pre-strip elution co-eluted less gold (0.2%) and silver (2%).

Mar 2, 2022

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By H. V. Alminas

The U.S. Virgin Islands consist of three major islands (St. Thomas, St. John, and St. Croix) and some 50 smaller islands that are located primarily along the coasts of St. Thomas and St. John. St. Croix, the largest of the islands, is located approximately 160 km south-southeast of San Juan, Puerto Rico and is about 218 km in area (Fig. 1). St. Thomas, the second largest island is located 64 km east of Puerto Rico and incorporates approximately 77 km2. St. John is located immediately to the east of St. Thomas and incorporates approximately 49 km2. The climate in the U.S. Virgin Islands is maritime tropical. The average annual rainfall at higher elevations is 127-152 cm and at lower elevations 51-76 cm. There is no well-defined wet or dry season. Temperatures generally average in the 80's (F°) with only a 5°-7° F variation throughout the year.

Jan 1, 1987

By B. Gorain

"INTRODUCTION The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast. Keywords: Digital Transformation, Operational Intelligence, Gold Recovery, Mine to Mill integration, Planning and Execution strategy, Theory of Constraints. Challenges Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance. Consequently, over the last few years, there has been a major focus amongst some mining companies to imbibe Operational Excellence. This has been only possible because of the replacement of a silos based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organization is not trivial. Attempts in the past to integrate functions such as through Mine-to-Mill initiatives in the mining industry have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turn over and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate.Opportunities The advent of digital technology has opened-up opportunities to integrate inter-departmental information for a unified understanding of, and across, an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/Historian) and industrial networks have helped in the direction of enterprise wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan & Gorain (2016), some of the potential opportunities are as follows:"

Jan 1, 2018

By S. Tandanand

The Bureau of Mines, U.S. Department of the Interior, assessed the geological effects on the ratio of maximum subsidence and extraction thickness, hown as the subsidence factor, to develop a simple method for predicting the maximum subsidence. The study is restricted to the Northern Appalachian Coal basin where data were collected from 13 coal mines. A model previously developed to relate the subsidence factor with the lithology and with the width and depth of working panels was used in the assessment. The result shows the possibility of determining maximum subsidence without resorting to a rigorous method.

Jan 1, 1982

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995