Search Documents

By James Donald Forrester

JAMES DONALD FORRESTER 32.1-EXAMINATIONS The field examination of a mineral deposit or mining enterprise requires a comprehensive effort to determine all natural and man-made factors bearing upon the problem to be resolved by the investigation. Therefore, the purpose to be served by an examination must be fully understood before the engineer assumes responsibility, and before actual field work starts. A clear understanding facilitates planning the approach to the project for maximum efficiency and thorough acquisition of information. It follows, of course, that the engineer has the necessary knowledge and experience to discharge satisfactorily the professional obligations attending the project. Some studies are in herently more complex than others, and the requirements of the problem are not always the same. Some examinations require the detailed investigation of large operating or nonoperating mines or, possibly, of mining districts; others involve more or less reconnaissance studies; and still others rela¬tively small undeveloped mineral occurrences. Likewise, the primary objective of some analyses may be the evaluation of a mineral deposit or a mining property, whereas in other projects the major objective may be guiding mining or drilling work in the discovery of new or hidden ore bodies and mineral-bearing structures. Thus, the possible range of any given examination may extend in varying degree through one, or more, of the following types of procedures: 32.1.1--GEOGRAPHIC ENVIRONMENT Studies of geographic environment should be made to ascertain the general physical situation in the area under consideration and to identify those correlative factors hearing on the, findings resulting from the field examination. This commonly will include determinations of: A. Location of the field area with respect to the state and county in which it occurs and, if feasible, a record of the township, range and section with reference to the principal meridian, and base line (or lines) that apply. For examinations in foreign countries, or in regions outside the continental United States, it is desirable that the field locality, in each instance, be identified with reference to the boundaries of some form of political entity essentially comparable in character to the divisions used in the United States. B. Distances from existing communities and related service centers, via: 1. Roads, both improved and unimproved. 2. Railroads. 3. Navigable waterways. 4. Airports. C. Topographic relief as it will influence the selection of 1. Pit site or positions of underground mine portals or shaft sites, including dump areas. 2. Mill site, including tailings disposal area.

Jan 1, 1973

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Clark Woodland, William E. Stanley

Mining companies have been required to enter a "new era of management" in the 1980's as they strive to become more efficient in an increasingly competitive market place. One response for many companies has been to modify their mine accounting systems to make them more effective for cost control and decision-making. This paper discusses some of the major issues in developing and implementing a standard costing system as part of improved management reporting and cost control procedures. It describes the key features and benefits of a computerized standard costing system with particular emphasis on budget-setting and variance analysis. It also identifies important factors to be considered in order to achieve successful project planning and Implementation.

Jan 1, 1987

By R. Aliberti, E. Comis, M. Wone

DC Water’s Clean Rivers (DCCR) program involves the construction of approximately 29 km (18 mi) of CSO tunnels in Potomac Group soils in the Washington DC area. Soils include an upper predominantly over-consolidated fine grained plastic material facies (P/A) and lower predominantly coarsegrained facies (PTX). As earth pressure balance (EPB) tunnel boring machines (TBMs) are mainly used in such soils, the correct approach to soil conditioning can make a considerable difference in TBM performance. Soil conditioning laboratory tests are often completed during the planning phase prior to TBM excavation to develop a baseline for soil conditioning, reduce risks, minimize costs, and improve performance. However, only a few basic tests are standardized to date, and conditioning regimes are fine-tuned during the mining phase. The paper illustrates the effort carried out to identify the correct soil conditioning regime for both PA and PTX facies to improve TBM overall performance and reduce ground movement during the excavation of the Northeast Boundary Tunnel (NEBT) in Washington DC.

Dec 1, 2022

By Joseph W. Leonard

By combining statistical methods with specialized coal technology, novel and widely applicable procedures are developed which are useful for making important decisions based on coal seam structure. By analyzing such properties as ash in visual coal types of seam cross sections and by processing the ash data to 100 gram increments of coal ranging from the top to the bottom of the seam, intraseam comparisons between data populations of samples from a given seam and a reference seam can be made. Moreover, illustrations are presented for estimating the number of drill cores required to purchase a specified level of sampling accuracy together with procedures for determining the probability that different coal scan cross sections are not unlike and by inference are therefore comparable. Such comparisons can be valuable when making important, costly and long prevaling decisions involving coal exploration, mining, preparation and utilization.

Jan 1, 1969

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By Venkata Aneesh

This paper examines the desired blast fragmentation results associated with mining fleet performance at Sidney Quarry of Pike Industries, A CRH Company by reducing cycle times and hauling less oversize material generated from the blast to the crusher to increase the overall plant throughput. We are constrained with blast patterns due to the poorly sorted and fractured seams in the quarry, which is angled at 35° NE and dipping at 80° and runs parallel to the Interstate-95 highway on the east of the quarry boundary about 600 ft, making it challenging to alter the blast patterns for optimal yield. We evaluated multiple relationships between blast patterns in conjunction with loader diggability. Results analyzed include the digging hours, fleet cycle times, and the fragment size with the optimized blast design through 3GSM software to arrive at the optimal yield to maximize the crusher throughput. Our primary objective is to focus on safety with efficient cycle times and clean floors & clean face generation for better operational efficiencies. Secondly, to optimize the crusher yield which is an integral part of quarry operation. Further, this paper provides the utilization of 3GSM blasting techniques in quarry applications with computer vision fragmentation analysis and VizaLogix, a fleet management software to analyze the cycle times sampling.

Feb 1, 2024

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993

By John E. Kinnison

The Mission mine, located in southern Arizona near Tucson, is a recently developed open pit which produces 15,000 tons per day of copper ore. The mine lies on a wide and gently sloping bajada sweeping northeasterly from the Sierrita mountains. It derives its name from the nearby Mission San Xavier del Bac, built circa 1700. The ore body is everywhere covered by about 200 feet of alluvium, as are the adjacent Pima and Palo Verde mines. The geology of the Mission deposit is known principally through the study of diamond drill holes spaced 150 to 300 feet apart. The open pit is in an infant stage and has not yet revealed much of the deposit, although information obtained there by the operating staff, and from a few thousand feet of exploratory underground workings, has added significantly to the general fund of knowledge. Permission to publish was granted by the American Smelting and Refining Company. I am indebted to Kenyon Richard and J. H. Courtright for criticism of this paper and for their direction during the several years in which I studied the Mission deposit. Acknowledgment is given to consultant in petrography, Robert L. DuBois of the University of Arizona. The only previous publication pertaining directly to the geology of file Mission deposit appeared in 1959 (Richard and Courtright), and may not be everywhere readily available. Cooper (1960) has published a short paper on the district

Jan 1, 1963

By R. J. Grace

Carbon in the form of coke is used as a reactant in various chemical and metallurgical processes, The high cost of by-product coke along with its periodic lack of availability and high investment necessary for additional by-product recovery facilities indicate the need for a low-cost production unit based on a new procedure for coke manufacture, Traveling-grate coking-stokers were developed by Shawinigan Chemicals Ltd. to produce coke required for carbide manufacture, They were adapted to kilns so that the hot volatile gases could be used for lime burning, Their operation has been described in various patent disclosures (1, 2, 3), and their application to rotary lime burning kilns has been described by Andersen (4). Details of the process and plants have also been published by Kurt Baum (5,6).

Jan 1, 1958

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By Konrad J. Banaszak

At least for the time being, these seems to be general but not universal agreement that Mississippi Valley type ore deposits formed entirely or in major proportion from heated connate brines (e.g. 1) Even with that agreement, major questions remain. I will present a coherent geochemical model and look at alternative views in the context of that model. The pattern of the following discussion is 1) the general geochemistry of the ore fluid, 2) the density-temperature relations and possible mechanisms of flow of those fluids, 3) the mechanisms of transportation and deposition of the ore minerals, and 4) a summary of a coherent model of genesis. The data equivocally define much about the deposits. The answer is still elusive.

Jan 1, 1979

By Wolfgang Güter, Paolo Romualdi

Current extensions of the European railway network require long TBM drives in the diameter range of 10 m under critical and varying rock conditions. In view of that and in particular for a 7 km long high-speed railway tunnel in Spain to be started in mid-2003 a new design for a hard rock Double Shield TBM has been developed by SELI (Italy) and Jäger (Austria) in collaboration with Mitsubishi (Japan)and Robbins (USA). Due to the new design and operational features that new type of TBM has been named Universal Double Shield TBM with a further extended area of application. Special attention has been given to outstanding torque and thrust capacities combined with the shortest possible length of an innovative shield arrangement, different advance modes in various ground conditions and further developed exploration and treatment facilities.

Jan 1, 2003

By Peter Hornby, Maurice Craig, Franklin G. Horowitz, Don Bone

We have developed a high-performance, flexible scheme for interpolating multi-dimensional data. The technique can reproduce exactly the results obtained, for example, from Ordinary Kriging and related techniques in 3D, or from Thin-Plate Splines (Briggs' minimum-cuwature algorithm) in 2D. Moreover, com- pared to traditional implementations of these algorithms, our method enjoys large computational-cost savings. The new approach produces an interpolation that obeys a Partial Differential Equation (PDE). The PDE may arise from physically based arguments, but its form can vary widely. It might be specified only implicitly (as through a Model Variogram), or be nonlinear (although a performance penalty could then apply). While a formal equivalence between Kriging and Splines has been known for some time (Matheron, 1980), the present derivation, from radial basis functions, further illuminates this connection. Thus, for example, we can make explicit the PDEs that underlie some of the Model Variograms most often used in Geostatistics. Besides its practical utility, the work thereby ac- quires a theoretical interest.

Jan 1, 1996

By Paul H. Johnson

A new system for leaching many types of ores has recently been developed on a commercial basis by J and J Research and Development, Inc. of Hanover, New Mexico. This revolutionary new leaching system consists principally of three new leaching reactors; viz, (1) a large, air-agitates, column-like reactor for leaching crushed ores that is constructed in an underground environment and has the inherent ability to do a very efficient job of leaching, (2) a vat-like, air-agitated vessel for leaching an rinsing finely ground ores and , (3) an air-agitated copper precipitation column that is built underground and utilizes an inexpensive dense or heavy scrap iron as a copper precipitant. Each of these new reactors have been used in a large leaching plant near Hanover, New Mexico.

Jan 1, 1973

By John McMorran

An open pit mine design system should have the characteristics of being flexible, versatile, and simple. All of these characteristics are necessary for producing a dynamic mine design. In other words, a design that can be improved, updated, and implemented. Flexibility is an important characteristic due to changing times. For example, the effects of a changing economy, increased knowledge of the mineral deposit, or improvements in mining technology can result in a considerable, if not a complete change in the long range mining plans. Since the short range mining plans are based on the long range mining plans, they will-also be effected. Also, it is very important to validate the information used in the design or the design itself. This means the system should have the flexibility of being able, not only to detect, but to correct errors. Versatility is another important characteristic of a mine design system due to the wide range of situations that may appear. First, a design system must be able to handle both long and short term planning. This is necessary because of the variability in the definition of a time range. Second, a design system must be able to handle different types of deposits. Special emphasis must be placed on this issue, because many deposits, if not the majority, do not fit predefined categories such as bedded, massive, or roll-front, etc . . . Furthermore, the true test of the versatility of a design system is not only the ability to create an ultimate design but also to schedule sequences for this design. Thus, the versatility of being capable to design with a variety of time ranges, variety of deposit types, and scheduling are all important characteristics of the design system.

Jan 1, 1982

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986