Search Documents

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By Doandy Yonathan Wibisono

Shotcrete is a versatile and widely utilized rock support material in mining and civil engineering projects due to its adaptability, strength, and efficient application. It immediately stabilizes rock surfaces, effectively controlling loose materials and preventing rockfalls in underground excavations. This paper focuses on assessing and analyzing data from observations of nozzlemen (shotcrete sprayers) during primary ground support activities in an underground mine. The study highlights the importance of nozzlemen’s skills in ensuring the quality of shotcrete application, which is critical for underground mining operations’ structural integrity and safety. A comprehensive training program and field support were implemented to enhance the nozzlemen’s proficiency. The training set covered theoretical knowledge and practical techniques to improve shotcrete application daily. Proficiency improvement was assessed using quantitative metrics, with rebound percentages decreasing by 5–14% as nozzleman competency increased. The results of this initiative showed significant improvements in shotcrete quality, including increased efficiency, reduced waste, and fewer reworks or rehabilitations. The findings aim to contribute to a broader understanding of best practices in shotcrete application and nozzlemen training, ultimately enhancing ground support application measures in the mining industry.

Feb 1, 2025

By James R. Dunn

The mineral industry" has made and will continue to make important contributions to the growth of our economy. However, the industry is presently under continuous and increasingly severe attacks by organizations and individuals interested in the preservation of our environment. Yet neither the public interest value of preservation nor the public interest value of our mineral industry is known. In the absence of such values, judgments about best land use where minerals are involved are nearly always made on emotional grounds. An example of the sort of problem that has been created is in the New York Metropolitan Area. Because of institutionally-created shortages stemming largely from zoning decisions and building over deposits, the effective cost of fine aggregate delivered at dockside at Manhattan rose from $2. 65/cubic yard in July, 1969, to $4.10/cubic yard in May, 1970, this in spite of approximately ;l0,000 years of reserves on Long Island. The cost of fine aggregate for New York City alone has "Increased over $S million annually within one year, with the cost increase for the Tri-State Metropolitan Area (coastal Connecticut, New Jersey, and New York)" exceeding $10 million annually. The ab0ve situation has created a cost increase which is clearly the result of non-conservation of a mineral resource. That is, in readily measurable values, it Is costing the public about $10 million per year because good conservation practices were ignored-a public-interest loss. Admittedly, this is not the whole story because the public is simultaneously obtaining other values from the land surface that would otherwise have had to be dedicated, temporarily to be sure, to mineral recovery-a public-interest gain. However, the point is that we do not know where the balance lies-the net public interest value; it may lie one way for deposits zoned out of existence by a growing suburb, another for areas designed as permanent greenbelts, and still another for areas under new highways

Jan 1, 1971

By Warren E. Morrison

The expansion of the United States economy in the postwar period has had a tremendous impact on the demand for energy. Not only has total energy consumption increased at an unprecedented rate, but there have been major shifts in the composition or mix of energy resources within the end-use sectors. Because of the numerous interrelationships between substitutable energy resources and their markets, the energy economy can only be analyzed in terms of the trends of its component parts. This problem takes on additional complexity when attempting to chart the nation's future energy requirements. Total energy consumption can be forecast with reasonable accuracy for periods up to 15 years by relating this to projections of economic indicators. However, forecasting the component parts of the energy economy constitutes a dilemma in that the sum of the projected parts frequently exceeds predictions for total energy. Areas of uncertainty in energy forecasting tend to mount rapidly when proceeding from total energy to the consideration of specific energy resources consumed as fuel, power, or raw materials.

Jan 1, 1965

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By P. Massacci

The modelling of phenomena by nonlinear dynamic Systems Theory representations require the specification and identification of suitable models of the phenomenon and the availability of good optimization algorithms to determine the optimal controls. Stochastic disturbances and difficulties of monitoring the process lead invariably, otherwise, to suboptimal performance. It will be shown that an algorithm can be formulated which will simultaneously identify and optimize such a system. The properties of the algorithm will be derived and its convergence to an optimal control proved. Some results of actual applications will be presented and it will be shown how this approach generalizes easily to optimal control of the actual processing system. These results generalize those of optimal learning and input conditioning.

Jan 1, 1991

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. Alternatively, the organic efficiency parameter does consider process economics; however, it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach is introduced which reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure which reflects a better use of performance data. INTRODUCTION Partition curves are commonly used in the characterization, evaluation, and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, and density separators. Graphically, the partition curve depicts the recovery of particles as a function of a physical property on which the separation is based (e.g. particle density, size, magnetic susceptibility, etc.). Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic “S” shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout (or bypass) values, the midpoint slope, and the separation cut point (property value with 50% recovery). Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of the calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, since a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point (i.e. an infinitely large slope). One common formulation of this slope, the Ecart Probable (Ep), is derived by evaluating the slope between the 25% and 75% recovery points:"

Jan 1, 2015

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By Raymond Sandiford, Kenneth Xu, Taehyun Moon

Tunnel approach structures situated in slow moving earth flows are subjected to significant earth pressures. The authors have developed a system, utilizing collapsible concrete columns, that limits such loading. The system uses an array of collapsible concrete columns in front of the structure to absorb downslope movement and limit-imposed loads. This concept has been modelled using 3D FEM analyses and a rudimental lab test. For implementation, the collapsible columns would be prefabricated in strengths to mimic the soil strength profile. This concept has merit, and analytical results demonstrate that collapsible columns are a viable means to limit loading.

Jun 23, 2024

By S. A. Anzalone

The Helvetia copper deposit is a large undeveloped Laramide porphyry copper system located in the Santa Rita Mountains, Pima County, Arizona. This porphyry copper system consists of four areas of copper mineralization: Rosemont, Peach-Elgin, Broadtop Butte, and Copper World. Asarco refers to the four areas collectively as the "Helvetia Deposit". Mineralization and alteration are primarily contact pyrometasomatic, and zoning of hydrothermal alteration and sulfide mineral assemblages are similar to those observed at the Twin Buttes and Mission copper mines located approximately 32 km west of Helvetia. Asarco acquired the Helvetia Deposit in 1988 and has continued the exploration and development effort since then. A considerable amount of excellent geological work has been completed in the area but little information has been published on developments since the mid-1950's. The geology of the deposit as developed by numerous geologists over the past 75 years and the large, bulk tonnage low grade copper deposits outlined in recent years will be briefly reviewed in this paper.

Jan 1, 1992

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010