Search Documents

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study was conducted to remove iron from sulfate solu¬tions using Eichrom'sDipex®extractant, PP'-di(2-ethylhexyl) methanediphosphonic acid (H2DEH[MDP]). It was found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. More than 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 2000

By James Corcoran, Richard McLane, Joseph DeMello, Eric Carlson, Hans van de Vrugt

The Los Angeles County Transportation Authority’s Purple Line Extension Phase 1 is a $3.12 billion (USD) design-build, underground heavy rail project, connecting an existing station at Wilshire Boulevard and Western Avenue and extending west 3.92 miles under Wilshire Boulevard and terminating approximately 550 feet west of Wilshire/La Cienega Station. The project alignment runs through the heart of the world famous La Brea Tar Pits and one of the world’s largest urban oil elds. This paper presents a case history of the planning, design, and construction efforts to achieve successful construction of the bored tunnels through Reach 3 of the alignment. Further, this paper outlines the proactive partnership between the owner, Los Angeles County Metro (Metro), the Design Builder, Skanska-Traylor-Shea oint enture (STS), and Southwest Geophysics who provided the geophysical services. Specically, the project included background review of historic site data (e.g., oil eld maps, building foundation plans, historic aerial photographs, etc.), geophysical demonstration testing to ascertain the capability of borehole magnetics to detect oil wells, directional drilling of thousands of feet of horizontal and vertical boreholes, collection of high resolution magnetic gradiometer data along vertically and horizontally cased boreholes as well as the collection of surface magnetometer data, discovery (“ground truthing”) of detected geophysical anomalies, and abatement of potential obstructions within the tunnel alignment.

Jun 23, 2024

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA's general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By Xuezhong Wang, Hao Guo, Tao Tu, Qingsheng Liu

The scheelite concentrate was leached with a mixture of sulfuric and oxalic acids. Chemical compositions, mineral phases, and morphology were characterized by XRF, XRD, and SEM–EDS. Based on the results of the single-factor experiments, the response surface methodology (RSM) was chosen to optimize the leaching parameters: temperature, time, and concentrations of sulfuric and oxalic acids. The RSM results indicate that the optimum values for those parameters are as follows: temperature 72 ℃, sulfuric acid concentration 1.48 mol/L, oxalic acid concentration 0.96 mol/L, and reaction time 2 h. Under the optimal leaching conditions, the model predicts a maximum leaching yield of 99.5%, compared to the value of 99.1% obtained experimentally, that is, a discrepancy of only 0.04%. This good correlation shows that the quadratic polynomial equation obtained by the RSM optimization is reliable. The importance on leaching parameters of scheelite is, in decreasing order, temperature, time, sulfuric acid concentration, and oxalic acid concentration.

Oct 11, 2021

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By Ken E. Baylis

Current over-capacity in coal production provides assured and relatively low-cost supplies to coal importers. At the same time, it is of serious concern to coal producers who invested considerable sums in the expectation that overseas demand would continue to grow rapidly. This paper assesses the reserves available for export, the export facilities, the coal supplies which can be put through them, and the market prospects for the future. It assumes, rightly or wrongly, that there will be no major and prolonged disruptions in supply from any major sources of coal. COAL RESERVES FOR EXPORT Economically recoverable reserves in the non-communist world amount to about 470 billion tonnes. These are sufficient to sustain current production levels of 2 billion tonnes a year for 235 years.

Jan 1, 1984

By F. S. Knoll

Electrostatic separation is one of the most misunderstood physical processes used to beneficiate minerals. Nonetheless, millions of tons of titanium ores, iron ores and other minerals are processed every year economically, efficiently and safely. Over the past ten years major advances in electrostatic separation and its application have occurred. New processes include dewatering clay slurries, separating halite and sylvite, and shape separation of vermiculite and gangue minerals. Electrostatic separation techniques are based on one of two methods, electrophoresis or dieleccrophoresis -- processes involving charged and uncharged particles respectively. In some cases, the combination of these two techniques has proven quite useful. The purpose of this paper is to provide a basic understanding of the physical processes collectively called "electro- static separation" in order to enhance one's ability to define and consider new possibilities in mineral processing and other fields.

Jan 1, 1984

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

By John C. Stankus, Xiaoting Li

"Underground structures such as square/arch steel sets, king beam structure, etc. are widely used for the roof support in underground mines. In designing and calculating the required carrying capacities of these underground structures, how to identify the potential rock loads on the structures over long term is a challenging question for ground control engineers. Based on design practices of both surface and underground structures, the authors have designed and applied appropriate load factors in underground structural design projects to accommodate different rock types, entry/intersection dimensions, roof geologic conditions, availability of roof bolts and water, etc. Classification of load (reduction) factors for large-span underground intersections are presented for reference. Success of designed underground structures in effectively controlling roof stability over years indicates the applicability of the load factor concept for underground structural design, and its same significance as of the load factor specifications in ASCE/SEI 7-10, ANSI/AWC NDS (2015), and AASHTO LRFD Bridge Design Specifications (2012). The load factor concept will facilitate ground control engineers to appropriately utilize popular structural design software, such as RISA-3D or -2D to efficiently design and analyze underground structures.LOAD FACTORS IN STRUCTURE DESIGN APPLICATIONSIn structures, loads cause stresses, deformations, and displacements. Assessment of their effects is carried out by the methods of structural analysis with the help of load factors. Loads can be increased or decreased by load factors to meet the requirement that design strength be higher than maximum loads. For example, in designing a staircase, a dead load factor may be 1.2 times the weight of the structure, and a live load factor may be 1.6 times the maximum expected live load based on the Load and Resistance Factor Design (LRFD) method. These two “factored loads” are combined (added) to determine the “required strength” of the staircase. Some typical load (adjustment) factors used for structural design are as follows:"

Jan 1, 2019

By B. T. Lusk, J. M. Hoffman, J. Silva Castro

Blast vibration induces sounds within neighboring residences. A housewide vibration and sound monitoring system was installed in a West Virginia home subjected to blasts from various distances and directions. Eighty-nine blast events were monitored and analyzed. Fifteen channels of data were collected, including data from three triaxial geophones, one airblast microphone, one uniaxial geophone mounted on the wall of the house (response channel) and four microphones that recorded CD-quality sound waves inside the house. Each of these channels was recorded on the same time scale. The response channel signal was easily separated into ground vibration and airblast-induced movement, due to differences in the time of arrival. This response channel was then compared to the sounds recorded to determine which component of blast vibration induced the maximum sound response. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast, while for blasts beyond 762 meters (2,500 feet), the maximum sound response was caused by ground vibration without exception. When airblast was identified as the dominant sound generator, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator, the peak amplitude of sound was not related to the amplitude of ground vibration. Findings from frequency analysis showed that the frequency content of sounds inside the house was not related to the frequency content of airblast or ground vibration, regardless of source. This finding suggests that residents will have difficulty determining the source of blast-induced noise in their homes. The proposed airblast response factor (ABRF) can aid blasting operations to determine the dominant source of sounds inside a complainant’s house based on the time-of-arrival relationships. With this site-specific information, public relations responses can be developed accordingly.

Jan 1, 2010

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environ-mental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 1, 1977

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By William Gleason

There was a time, not too long ago, when the most daunting challenges facing those in the mining and mineral processing industries could be solved through better technologies and better practices. But now the challenges that come from the actual acts of mining and processing are just part of the bigger picture. SME?s Colorado Section of the Mineral Processing Division (MPD) hosted its 63rd annual meeting at the Broadmoor Hotel in Colorado Springs, April 25-27 and, while the conference had its fair share or mineralolgy and processing presentations that were heavy on the technical side of things, this year?s conference was also focused on the issues of permitting, regulation compliance and legislative issues. The so-called ?softer? issues, that, if not addressed, can lead to very real and very hard challenges. Under the theme ?Mine your own business - permits, startups, expansions and resources,? even the most dedicated metallurgists were drawn into the discussions of politics and legislation, and how those issues affect their business. Fittingly, Colorado Mining Association (CMA) president Stuart Sanderson was honored with the Arthur C. Daman Lifetime Achievement Award. Sanderson, an outspoken proponent for the mining industry in Colorado and beyond, also presented the keynote address to the lunch crowd where he spoke about framing public opinion toward mining and the efforts of the CMA to move the public opinion dial in a direction more favorable to mining. Sanderson explained that Colorado, once a Republican stronghold, turned after 2002 and now is controlled by Democrats who are traditionally less supportive of the mining industry. Sanderson said the deciding factor in the power shift was money, as supporters of Democrats outspent Republicans in the most recent election cycles. CMA has done its part to keep mining going in the state with a broad marketing campaign that was outlined by Sanderson.

Aug 1, 2013