Search Documents

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By A. M. Whiting

Competition for coal producers and their primary customers has constantly increased during recent years. The effects of the Clean Air Act Amendments of 1990 on the electric utility industry, coupled with the normal complexities of coal production, quality control, transportation and contracting techniques have spurred both buyers and sellers to increase their level of sophistication. This paper will review the basic aspects of the U.S. coal business and explore the commercial approaches which have proven to be most successful.

Jan 1, 1994

By Nick Barton

The ability to estimate that support is unnecessary for various dimensions of opening in certain rock mass environments is of particular relevance in the mining industry, where most excavations are not expected to remain open indefinitely. As Hoek1 observes: "the basic aim of any underground excavation design should be to utilize the rock itself as the principal structural material, creating as little disturbance as possible during the excavation process and adding as little as possible in the way of concrete or steel support". Approximately two hundred case records have been analysed for the purpose of determining the amount of permanent support normally used when a given span is excavated in known rock mass conditions Some thirty cases concerned unsupported openings. Excavations that can stand unsupported appear to have certain common characteristics as regards rock mass quality. However, the mechanical properties of the rock mass are not the only factors controlling the choice of design. The dimension of the opening (span or height) and the type of excavation are two important variables.

Jan 1, 1975

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

By David L. Brostrom, William C. Brice, Perry A. Canton

The business of mineral exploration and development has become much more than simply a problem of locating orebodies and designing mines. Favorable economic analysis of mining and processing feasibility is no longer sufficient to justify the development of a mine. New laws, enacted by virtually every level of government, require comprehensive land use planning, environmental analysis, mineland reclamation, mine safety studies, and many other considerations. This profusion of new laws says in effect, that the mining company is no longer responsible only to its stockholders. Mineral development today can be compared to a partnership. As in all partnerships, the risks and liabilities as well as the benefits are held jointly by all the participants. In addition to the mining operator, this partnership consists of the public, through its many levels of government, interest groups, and individual citizens. Therefore, you'd better know your partner very well - his responsibilities and capabilities. Mining is considered a high risk venture. The risk on the part of the operator and the lending institutions has long been recognized. The risk that the public and its government take in these mining ventures has now been recognized also. The people and their government have learned that they inherit, through abandonment or forfeiture, the mistakes and problems of individuals and companies regarding these natural resources. In looking through the "Mining Engineering Handbook" recently published by the Society of Mining Engineers, I noted that in their discussion of liability for excavations, the authors quoted from the book of Exodus, 20th chap., where Moses said to his people: "When a man leaves a pit open, or when a man digs a pit and does not cover it, and an ox or an ass falls into it, the owner of the pit shall make it good; he shall give money to its owner, and the dead beast

Jan 1, 1974

By Feridon Ghadimi, Saeed Mojeddifar, Massume Khavari

Separation of geochemical anomalies from background is an important and essential issue in the exploration of mineral deposits. Statistical methods are used to separation of anomaly from background. Fractal/multifractal and singularity methods are very suitable for the separation of weak anomalies. For interpolation, various methods could be used such as most distance-weighting methods, kriging, spline interpolation, interpolating polynomials, and finite difference methods. This paper addressed application of multifractal techniques together with finite difference procedure to detect the anomalous regions. Fractal models such as concentration–area, spectrum–area, and singularity index model were selected to identify Pb–Zn anomalies. In this research, 170 samples from 33 boreholes were taken in the Haft-Savaran area and analyzed for determination of Pb–Zn anomaly. Singularity method was a suitable method for separating Pb and Zn anomalies. Also, the results showed that the geochemical anomaly has occurred along NE–SW trend and is consistent with the sulfide mineralization process and the faults of the region.

May 18, 2020

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

By S. Vogely, J. Trescot, D. Connor, F. Beloy

In 2001, the Minntac Division of US-Steel retrofitted one of their Grate-Kiln Iron Ore Pelletizng lines with a Ported-Kiln Air Injection System (PKAIS) the first of it’s kind in the world for oxide pellets. The Ported Kiln System injects air under the bed of pellets in the rotary kiln, causing rapid oxidation of the magnetite pellets. This rapid oxidation allows for lower kiln temperatures, reducing fuel demand; less heat load on the annular cooler; and higher pellet quality. Both the process and the equipment are patented developments by Metso Minerals. This paper discusses the process, the key equipment, and the benefits to the pellet plant and the downstream blast furnace operations.

Jan 1, 2004

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By T. Takamori

This paper reviews the present status of coal preparation in Japan concentrating on the process in coal cleaning and waste water treatment. This paper also discusses recent topics on maintenance, automatic control, raw coal management, etc.

Jan 1, 1982

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

Jan 1, 1999

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By David R. Delling

Tenneco is a large, diversified, energy-based company which has grown rapidly during its forty year life. We're the youngest corporation among Fortune's top 20 companies. Tenneco Minerals Company is the division of the Corporation responsible for nonfuel minerals exploration, development and operations. Tenneco Minerals Company is headquartered in Lakewood, Colorado. Exploration offices are in Colorado, Nevada, Alaska, and Perth, Australia. We currently operate two gold mines in Nevada and a large underground trona mine and soda ash processing plant in Wyoming. The latter has a capacity of 907 000 tonnes per year of soda ash and is the subject of my presentation today.

Jan 1, 1984