Search Documents

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

The accurate estimation of ore reserves along with capital and operating costs are two key components to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by improper estimation of ore reserves. The accurate estimation of ore reserves for any deposit relies heavily on understanding its geology and underlying assumptions unique to the estimation techniques being used. The assumptions unique to commonly used traditional and geostatistical reserve estimation technique will be reviewed. The shortcomings of the estimation techniques and their possible impact on a given project's economic outcome will be discussed. The latest developments in geostatistics in overcoming existing reserve estimation problems will be presented.

Jan 1, 1994

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By Egons R. Podnieks, Wallace W. Roepke

Mining technology to utilize vital lunar resources will be required for any commitment to permanent lunar basing. Lunar mining must be viewed both as a major supporting element for space resource commercialization and for creation of human settlements on lunar and planetary surfaces to support long-range space exploration. The Apollo missions to the lunar surface and results from fundamental research on analogue lunar rocks by the Bureau of Mines, and others, have provided the initial data for developing lunar mining technology. The multi-disciplinary research projected in this paper outlines the scientific and engineering needs to realize the lunar mining goals.

Jan 1, 1990

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

By J. K. Horbaczewski

The reclamation of an open dragline pit (Pond A3P-2) at the Gibbons Creek lignite mine in east-central Texas required neutralization of acid mine pit water. At the start of treatment with hydrated lime (Ca(OH)2) on March 28, 2000, the pond had partially filled with 913,000 m3 (740 acre ft) of pH 4.9 water. Another 666,600 m3 (540 acre ft) of pH 3.3 water was pumped in from an adjacent pit (PitA3P- 1). By the end of the project (July 5, 2000), a combined volume of 1,579,000m3(1,280ac-ft or 417milliongal) in PondA3P-2 had been successfully treated to pH 8.2 with 431 t (475 st) of lime. This was two to three times more neutralizer than laboratory trials and detailed chemical titration had predicted. The main reasons for the difference are thought to be the inadequate representation in a laboratory setting of some of the chemical reactions that occurred in the field, including incomplete mixing of reactants, reactions with clay minerals in the pit walls, the kinetics of biologically-mediated reactions and the kinetics of aluminum oxyhydroxide polymerization (aging).

Jan 1, 2002

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By Stanley W. Ivosevic

The South-Central area of the Osa Peninsula, Puntarenas Province, on the Pacific coast of southern Costa Rica, may have produced on the order of 30,000 kg (100,000 troy oz) of gold since prehistoric times. The Peninsula lies along an 800- to 900-km-long belt of late Mesozoic eugeosynclinal rock deposition, hydrothermal activity, and deformation (Campanian). The oldest rocks exposed in the area are basalt and tuffaceous mudstone of the Late Jurassic or Cretaceous Nicoya ophiolite complex. The Nicoya Complex is overlain by weakly lithified Pleistocene Older Sediments, predominantly conglomeratic sandstone and derived from erosion of the Nicoya Complex. Erosion reduced the Complex to a surface of high relief, so that the detrital source was in the area originally; the source retreated with subsidence. Stratigraphically, the Older Sediments are followed by surficial deposits of intermediate age, consolidated Younger Sediments reworked from Older Sediments, and unconsolidated Holocene surficial deposits reworked from Younger Sediments. The most prominent structures are a northeast-trending anticline and northeast and northwest fault sets. Some deformation was Cretaceous, but folding and much faulting occurred after deposition of the Older Sediments. Remnants of plainlike features and destructional terraces on the Older Sediments attest to stepwise downcutting of the terrain during successive stages of uplift. Near the end of this process, the present valley floors and coastal headlands developed. During a probable epeirogenic rise in sea level, Younger Sediments filled the valley bottoms and an aggradational coastal plain developed. Sea level dropped by stages and with some reversals to its present position; this caused stepwise incision of the valley fill, stepwise beveling of the coastal plain, and development of the present wave-cut platform. Spilitization around the time of the Campanian orogeny caused some parts of the Nicoya complex to be calcitized and others to be silicified. Gold, pyrite, and probably additional silica were introduced during subsequent hydrothermal activity. Native gold was eroded from Nicoya Complex lodes and reconcentrated through three generations of placer gold deposits. First, the gold was deposited as a detrital.

Jan 1, 1977

By S. Maurigiannakis

In an effort to promote sustainability in the construction industry, the natural decorative stones that cover large external areas of buildings may be replaced with artificial stones. In this paper the physical and mechanical properties of artificial decorative stones are presented and are critically compared with corresponding natural stones. To test suitability for various applications, artificial stone specimens were subjected to weathering testing (freezing-thaw cycles in a climatic chamber). Mechanical characterization of these specimens was based on uniaxial compressive testing as well as non-destructive ultrasonic testing. Preliminary results show that artificial stones can replace natural stones, thus creating a sustainable development option for the construction industry.

Jan 1, 2003

By R. Adsero

"In view of the decade long decline in worldwide mine equipment productivity and with heavy economic pressures and survival at risk, improvements for those remaining in the game are essential. The latest Multifactor Productivity data for the US mining industry indicates a continuing descent with Australia on a similar course. The world’s mining industry has a fleet of over 400 large draglines moving billions of tons of material annually. The most efficient use of this equipment resource will provide a competitive advantage to those companies who are committed to improving performance. A dragline monitoring system is a requirement for optimum operations. The monitor reports the facts. Focused actions can change the facts and create improved performance. Analyzing monitor data to build knowledge and create understanding is a beginning. Understanding the key productivity indicators for dragline operations and an effective benchmarking process are the basis for improvement. There is overwhelming evidence that adopting new technologies and concepts including AC drive technology can and will bring about a step change in dragline operating cost with improved production performance.STATE OF THE MINING INDUSTRY A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower and lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts the worlds mining equipment productivity has declined 20% over the past seven years. (Lumley, 2014) Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear. The world’s mining industry fleet of well over 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually.This discussion will review a few of the tools available for improved productivity in dragline operations."

Jan 1, 2016

By Pasi Latva-Pukkila

Underground rock drilling has gone through intense development during the last 25 years. Mechanization and hydraulics have greatly increased the efficiency of drilling and improved the environment of the drill operator. As the total economy has become more and more important, the development has resulted in greater overall economy in drilling. The latest evolution step is computerization of drilling equipment. Computerization has been applied to tunnelling jumbos, long- hole drilling rigs and bolting rigs. With today&apos;s technology computerization is the natural way to increase capacity and productivity of the drilling process. However, it is still impractical to implement total "robotic" drilling. In computerized drilling the operator&apos;s role continues to be vital in controlling the drilling process and in analyzing the effect of individual parameters on the whole excavation process. Today this is called "CAD" - Computer Aided Drilling.

Jan 1, 1989