Search Documents

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two o f the pit lakes, 26- and 55-m (85 and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper, pit lakes, 110 and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1997

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By Clayton Williams, Dale M. Hata, Glenn M. Boyce

The Upper Llagas Creek Flood Protection Project in Northern California encompasses portions of the communities of Morgan Hill and Gilroy, and unincorporated areas of Santa Clara County. The project provides for flood protection improvements along Llagas Creek and two of its tributaries, West Little Llagas Creek and East Little Llagas Creek. Llagas Creek is one of the tributaries of the Pajaro River and drains a watershed of approximately 104 square miles. The river system has a history of flooding the watershed communities, and the project’s goal is to provide 100-year flood protection by creating a bypass infrastructure, including channels, cut-and-cover culverts, and a tunnel. The project has been divided into several phases. This paper describes Phase 2A, which consists of approximately 2,150 linear feet of lined horseshoe-shaped bypass tunnel measuring 14 feet wide by 12 feet high. The bypass tunnel was sequentially excavated using a combination of roadheader and controlled blasting through colluvium and weathered to fresh greenstone. The tunnel was mined near residences, requiring strict noise and vibration controls. Phase 2A also includes the construction of twin bypass concrete culverts, portal shoring, and dewatering systems. It features the use of a Design Review Board and partnering for project delivery. This case study discusses the bypass tunnel design, progress of tunnel construction, plans to complete the work, construction risks, and the software and procedural tools being used to manage the project, including ProjectWise construction management software.

Jun 13, 2023

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By John Rajala

The Otjikoto Gold Mine in the Republic of Namibia is located approximately 300 kilometers north of the capital city of Windhoek. The project features surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and recovery of gold. Initial mill design capacity was 2.5 million tonne per annum but then expanded after 9 months of operation to 3.1 million tonne per annum. The technical steps to establish the Otjikoto mill design from process selection in the due diligence stage, through flowsheet development in the feasibility study followed by detailed engineering design are reviewed in this paper along with mill performance during start-up and in 2019.

Oct 30, 2020

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By D. D. Runnells, G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two of the pit lakes, 26- and 55-m (85and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper pit lakes, 110- and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1998

By H. Wagner

Recently a detailed study ?Minerals Planning Policies and Supply Practices in Europe? has been completed. The study, conducted on behalf of DG Enterprise, demonstrated that there are very few written down national minerals policies within European Union. Mineral policy elements are dispersed in many different documents and acts. The paper discusses the essential elements of minerals policies; particularly importance is placed in issues related to planning (land use planning, mineral development, etc.). A number of examples of successful and less successful mineral planning policy approaches are presented in other to support the idea of importance of comprehensive mineral policy. The main sources of information were the country reports of 26 European countries that are appendix of the study. We conclude that comprehensive written mineral policy that incorporates essential elements is crucial in order to achieve secure minerals supply.

Jan 1, 2007

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994