Search Documents

By R. F. Botha

I want to thank you for inviting me to deliver this, the closing address at the final plenary session of the 15th Congress of the Council of Mining and Metalurgical Institutions. Your Council has an impressive title, and justly so. Consider the expertise, the skill, the capacity, the achievement, that is gathered together here in this room this afternoon.

Jan 1, 1994

The comments by Mr Chaston were constructive and much appreciated. Considering firstly the recovery of cassiterite from fine deslimed material. A size distribution analysis shows that 58 per cent of cassiterite in Union Tin flotation concentrate reports in the minus 15 micron (quartz) size range. This is achieved at a recovery of 67 per cent and concentrate grade of 42,6 per cent. It is of interest to note that at Altenberg in East Germany 85 per cent of the tin in deslimed minus 43 micron material is recovered into a 14 to 16 per cent Sn concentrate using para-tolyl arsonic acid as collector. Reconcentration of this material is then carried out using two shaking table stages which recover 53 per cent of the tin in a 50 per cent Sn concentrate. Flotation was resorted to after recovery rates of 35 per cent and concentrate grade of 30 per cent had been achieved in a 275 ton per day plant comprising 130 tables. Tests on tabling of deslimed minus 43 micron material have not been carried out at Union Tin. The cost of equipment actually associated with cassiterite flotation amounts to about R60 000. The

By H. A. D. Kirsten

The effects of the mining of deep-level tabular reefs are usually evaluated by use of continuum, elastic mining simulation analyses. This paper gives the results obtained from a series of analyses in which stopes of limited span are considered to be excavated in a non-linearly non-elastic, jointed and fractured rockmass. In particular, the theoretical influence of soft backfill in these conditions is evaluated. It is shown that the stress distribution and behaviour of the rockmass, alternately taken as an intact-elastic and as a fractured non-elastic medium, are completely different. The relevance of the energy-release rate commonly calculated in mining-simulation analyses, and the efficacy of its correlation with seismicity and the associated rockbursts, are reviewed. In deep-level mining operations, it is not practically feasible to obviate releases of seismic energy. The fact of their occurrence should therefore be accepted and, rather than considering the reduction of energy release as the primary objective, efforts should be concentrated on minimizing the effects of such release. Analytical results are given to demonstrate that this approach is not only correct, but also the only feasible solution to the rockburst-seismicity problem in deep mines.

Jan 1, 1989

By G. Rebel

Owing to the helical construction of the wires and strands in a triangular-strand rope, a torque is generated when the rope is restrained and tensioned. When a rope is suspended vertically, there is a load differential along its length due to the self weight of the rope. This load differential gives rise to an initial torque differential m the rope. Since the rope is constrained only at the conveyance and sheave wheel, the torque along its length must be constant ID order to maintain equilibrium, a variation in lay length occurs so that the lay length at the conveyance end decreases, and the lay length at the sheave end increases, from the manufactured state. The tension-torsion testing of steel-wire ropes is discussed, and it is shown how the results of the tests can be used to predict static in-shaft torsional behaviour. The expected changes in strand lay length in very deep shafts (deeper than 2500 m) are calculated, and the associated problems and of severe changes m lay length on rope endurance and safety are discussed. Examples of current in-service rope distortions such as kinks and corkscrews are shown.

Jan 1, 1996

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By J. B. Parry

Three types of high-strength cold-rolled steels are discussed. Two are currently being developed at Iscor: rephos phorized steel and niobium microalloyed steel. Heat treatment after cold rolling is carried out in batch annealing furnaces. A third type, dual-phase steel, which requires a continuous annealing treatment for economic production, is also described. The properties, strengthening mechanisms, and applications of these three steels are examined.

Jan 1, 1983

By T. V. Thoms, T. R. Twidle, J. W. Crous

This note describes an investigation into the most cost-effective material for mil-shell liners in large-diameter pebble mils with lifter bars. This is part of a project being conducted at the gold plant of East Driefontein near Carletonvile in the Transvaal. It was found that manganese-steel and chromium-steel liners are more cost-effective than liners of cast mild steel or white iron.

Jan 1, 1990

By M. C. van Blerck

This paper examines the South African fiscal system as it applies to the mining industry and, where components are found wanting, discusses possible alternatives. It is concluded that the South African system has long provided a stable environment for mining investment and growth. However, the introduction, of steep surcharges during the past decade or so (since abolished) and ring fencing (since relaxed but not abolished) has started undermining this stability.

Jan 1, 1994

A theory is presented providing a concise mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions. The theory defines the relationships between the values of thrust required to produce optimum rates of penetration at different throttle air pressures in terms of the piston areas and derives an equation for the prediction of these rates. An analysis of drillsteel life and bit wear is also made.

By G. P. Schoonraad, J. E. Clay

Treatment of zinc silicates by the Waelz Process by J. E. CLAY (M.I.M.M.) (Visitor) and G. P. SCHOONRAAD. Pr. Eng.. B.Sc. Eng. (Rand) (Member) A review is given of the Waelz process. The chemistry of the process and the mechanism of crust formation (accretions) are briefly dealt with. The plant of Kiln Products Limited and its operation are described. The problems encountered and methods for their elimination are presented.

Jan 8, 1976

By R. G. Jurd

This paper considers the introduction of large-scale longwall mining into South African coal mining, instead of the conventional mechanized bord-and-plllar mining that is widely practised at present. The two methods are compared, and longwall mining is found to have the advantage in several respects in some seams. The most cogent reasons for the introduction of the longwall method In some seams are associated with safety strata control and increased labour costs.

Jan 1, 1978

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By D. M. Meyer, K. Auerswald

The production of electrolytic manganese in South Africa by M. HARRIS, Pr. Eng., B.Se. (Eng.) (Fellow), D. M. MEYER, Pr. Eng., B.Se. (Meeh. Eng.) (Visitor), and K. AUERSWALD (Visitor) The decision to construct the first electrolytic manganese plant in South Africa was important and farreaching. After evaluating the results of the pilot plant operation, the first South African producer, Electrolytic Metal Corporation (Emcor), established a plant in Krugersdorp. Initially, there were many process problems that had to be InvestIgated, and, after these had been solved and many operating parameters had been established, manganese was successfully produced. When the Delta Manganese plant in Nelspruit was planned, cognizance was taken of the fact that, if peak efficiencies were to be maintained, the process must be operated between fairly narrow parameters. Instrumentation was therefore installed to control the process automatically wherever possible. The main features of the Delta Manganese operation are outlined, with a brief description of each stage of the process from ore milling through to electrowinning and packing of the metal. It is concluded that much benefit can be obtained from further research work into process improvements and into the exact effect of certain variables on plant and current efficiency.

Jan 2, 1977

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

By J. J. S. de Beer, F. Hunter, A. F. Neethling

SYNOPSIS The paper describes the rib-pillar extraction method now used at Sigma Colliery in the Orange Free State. In this method, access roadways (with a high safety factor) are developed into a block of coal suitable for total extraction; pillars that have a low safety factor are then formed and extracted immediately. The method, together with the current practices of labour management, has resulted in better utilization of the coal resources and capital, increased production and labour productivity, and improved safety.

Jan 1, 1991

By P. J. Kinver

The paper presents details of the costs and outputs being achieved by South African mechanized tunneling and stoping drillings. The information was gathered from various hard-rock mining and tunneling operations ranging from deep-level gold mines to shallow base-metal mines. The survey included older pneumatic rigs and the newer electro-hydraulic rigs, but excluded shaft drilling and the stope drillings that were developed recently for narrow reefs. The information presented is intended as a guide to those having to decide whether to use mechanized drillings and, if so, what type and quantity

Jan 1, 1990

Notices EIGHTH WORLD MINING CONGRESS The Eighth World Mining Congress will be held in Lima, Peru, from 3rd to 8th November, 1974. The theme of the Congress is 'Prognosis of mining development up to the year 2000', with the following subthemes: INF ACON 74 Readers are reminded of the International Ferro-alloys Congress being organized by the National Institute for Metallurgy, in conjunction with the Ferro Alloy Producers' Association of South Africa and the South African Institute of Mining and Metallurgy.

By B. N. Soutar

The design and operation of a double- V compartment vertical-flow settler by B. N. SOUTAR, B.Sc. (Mech. Eng.) Wits. (Visitor) This paper describes the development of a vertical-flow settler for underground pumping installations in the mines of Gold Fields of South Africa Ltd. The recommended settler employs the principle of 'dynamic filtration': the solids that are in suspension in mine water are filtered through a stable horizontal bed of flocculated particles, a technique that was established in about 1958.

Jan 3, 1977

By A. Koursaris, Y. N. Turan

A series of experiments was caried out in a vacuum-induction furnace to investigate the solubility of nitrogen in stainless steel type 3100S. Melts were made under constant and variable partial pressures of nitrogen so that the absorption of nitrogen from the atmosphere could be examined. Additions of nitrogenized ferochromium were made to give high nitrogen contents in the steel. Nitrogen contents of up to 0,16 wt per cent were obtained under gaseous atmospheres. With additions of nitrogenized ferochromium, nitrogen contents of up to 0,525 wt per cent were obtained. Comparisons of the later value with existing data indicate that the equilibrium concentration of nitrogen was reached for the experimental conditions used.

Jan 1, 1992

By B. Rohrmann

The paper deals briefly with the history of vanadium, and its uses, price movement, and world resources. It then describes the titanomagnetite ore of the Bushveld Complex, and the production of vanadium from this ore at Highveld Steel & Vanadium Corporation Limited, giving details of the various processes used, including the roast-leach, rotary-kiln, electric-smelting, shaking-ladle, and basic-oxygen-furnace operations. The paper concludes with a very brief account of the treatment of Highveld slags in Europe for the production of vanadium pentoxlde and ferrovanadium.

Jan 1, 1985